2013 Lexus CT200h Maintenance

5537-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Remove the screws and take
off the mirror cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
After installing the new bulb,
secure the socket to the light
body.
When inserting the socket, align
the marks printed on the light
body and the socket.
4
5
6
7

5547-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Install the visor cover on the
mirror frame, secure it with a
screw, and install the side turn
signal light and outer foot
light.
Use only the screw position
shown in the illustration.
Side turn signal light: Align the
tabs on the light and the cover and
install.
Outer foot light: Interlock the tabs
in the groove of the light body
with those on the cover, and
secure.
Disconnect the tabs, and sepa-
rate the top and bottom of the
rear side cover of the mirror.
8
9

5557-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Install the cover of the back
end of the mirror, installing the
lower side and the upper side
in that order.
When installing the lower side of
the cover, insert the side turn sig-
nal light pin into the hole in the
cover.
Secure the cover with screws
and reconnect the connectors
back together.
Secure the cords by returning
them to the hooks as they were.
Align the tabs, and secure the
mirror by pushing in each
diagonally-opposite pair of
tabs in order.
Make sure to insert the tabs in
order as shown in the illustration,
and push them in until a click is
heard.
If you do not hear the click, do
not force the tabs in. Instead,
remove the mirror and check that
the tabs are aligned.
10
11
12

5567-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
Headlight low beams (LED type)
Daytime running lights and front position lights
LED front fog lights (if equipped)
Side turn signal lights
Stop/tail lights
High mounted stoplight
License plate lights
After replacing the bulbs
LED lights
The headlight low beams (LED type), front position lights, daytime running
lights, LED front fog lights (if equipped), side turn signal lights, stop/tail lights,
high mounted stoplight and license plate lights consist of a number of LEDs. If
any of the LEDs burn out, take your vehicle to any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional to have the light
replaced.
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not
indicate a malfunction. Contact any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional for more information in the fol-
lowing situations:
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
When replacing light bulbs
P. 537 After removing the power control unit
cover, return the cover to original position
with the clips.
Push up center portion
Insert
Press
1
2
3

5577-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
WA R N I N G
Replacing light bulbs
Be sure to stop the hybrid system and turn off the lights. Do not attempt to
replace the bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
Do not touch the glass portion of the light bulb with bare hands. When it is
unavoidable to hold the glass portion, use and hold with a clean dry cloth to
avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
Fully install light bulbs and any parts used to secure them. Failure to do so
may result in heat damage, fire, or water entering the headlight unit. This may
damage the headlights or cause condensation to build up on the lens.
Do not attempt to repair or disassemble light bulbs, connectors, electric cir-
cuits or component parts.
Doing so may result in death or serious injury due to electric shock.
To prevent damage or fire
Make sure bulbs are fully seated and locked.
Check the wattage of the bulb before installing to prevent heat damage.
NOTICE
When replacing the outer foot lights
If the front window is stopping you from conducting the replace operation
properly, open the window on the side you are working on to allow you enough
space to work. Continuing the operation without giving yourself enough space
to work could lead you to scratch the vehicle.

5587-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)

635
9Vehicle specifications
CT200h_OM_OM76102E_(EE)
9-1. Specifications
Maintenance data
(fuel, oil level, etc.)......... 636
Fuel information ............... 648
9-2. Customization
Customizable features....... 650
9-3. Initialization
Items to initialize .............. 661

6369-1. Specifications
CT200h_OM_OM76102E_(EE)
Maintenance data (fuel, oil level, etc.)
*1: Unladen vehicle
*2: Vehicles with 16-inch and 17-inch tires
*3: Vehicles with 15-inch tires
Dimensions
Overall length4350 mm (171.3 in.)
Overall width1765 mm (69.5 in.)
Overall height*11455 mm (57.3 in.)*2
1445 mm (56.9 in)*3
Wheelbase2600 mm (102.4 in.)
Tread
Front1525 mm (60.0 in.)*2
1535 mm (60.4 in.)*3
Rear1520 mm (59.8 in.)*2
1530 mm (60.2 in.)*3
Gross vehicle mass1845 kg (4068 lb.)*2
1790 kg (3946 lb.)*3
Maximum permissible
axle capacityFront1020 kg (2249 lb.)*2
1060 kg (2337 lb.)*3
Rear980 kg (2161 lb.)