2013 Lancia Ypsilon low beam

When the lights have been activated automatically
and are then switched off by the sensor, the
dipped beam headlights are switched off first,
followed by the side lights a few seconds later. If
the sensor is activated but is malfunctioning,
the side lights and dipped beam headlights are
switched on irrespective of the outside light level
and the sensor failure is indicated on the
instrument panel display. It is also possible to
deactivate the sensor and switch on the side lights
and dipped beam headlights.
IMPORTANT The sensor is unable to detect the
presence of fog. Under these circumstances, these
lights are therefore turned on manually.
MAIN BEAM HEADLIGHTS
To activate the main beam headlights, with ring
nut at
, pull the stalk towards the steering
wheel. The warning light
switches on in the
instrument panel.
When the stalk is pulled towards the steering
wheel again, the lights deactivate, the dipped
headlights reactivate and the
warning light
switches off.
It is not possible to switch on the main beam
headlights in fixed mode if the automatic lighting
control system is active.FLASHING
You can flash the headlights by pulling the stalk
towards the wheel (unstable position). The
warning light will come on in the instrument
panel.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
upwards:right-hand direction indicator
activation;
downwards:left-hand direction indicator
activation.
Warning light
or
should flash in the
instrument panel. The indicators switch off
automatically when the steering wheel is
straightened.
Lane change function
If you wish to signal a lane change, put the left
stalk in the unstable position for less than half a
second.
The direction indicator on the side selected will be
activated for 5 flashes and then go out
automatically.
56GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

GENERAL WARNINGS
❒The ultimate responsibility when parking is
always the drivers. During these manoeuvres,
always make sure that no people, animals
or objects are within the manoeuvring area. The
Magic Parking system (like parking sensors) is
designed to assist drivers: in all cases, you
must always pay the utmost attention during
potentially dangerous manoeuvres, even when
these are carried out a low speed:
❒If the sensors undergo shocks influencing their
position, the system operation could be strongly
degraded.
❒If the sensors are dirty, covered by snow, ice or
mud or are repainted compared to the original
conditions, the system operation could be
strongly degraded. It is vital that the sensors are
always clean in order for the system to work
properly. During cleaning make sure not to
scratch or damage them; avoid using dry or
rough cloths. The sensors should be washed
using clean water with the addition of car
shampoo if necessary. In washing stations, clean
the sensors quickly, keeping the steam jet/high
pressure washing nozzles at least 10 cm away
from the sensors.
❒Ultrasonic sound sources (e.g. pneumatic brakes
of trucks or air drills) nearby could negatively
influence the sensor performance.❒Sensors may detect a non-existent obstacle
(echo noise) due to mechanical noises, for
example while washing the car, in the case of
rain, strong wind, hail.
❒The sensors might not detect objects of a
particular shape or made from particular
materials (very thin poles, trailer beams, panels,
nets, bushes, parking deterrents, rubbish bins,
motor vehicles, etc.). Always take great care
to check that the car and its path are actually
compatible with the parking area identified
by the system.
❒The use of (one or more) tyres or wheels of a
different size to those at the time the car was
purchased could affect the operation of the
system.
❒If the battery is disconnected or is nearly flat,
the Magic Parking system will not be available
until the vehicle is driven for a few hundred
metres on a curved path to initialise the system.
❒If a trailer is fitted (with the plug correctly
inserted) the Magic Parking system will
automatically be disabled.
❒If the Magic Parking system is in "search in
progress" mode, the system could incorrectly
identify a parking space and carry out the
manoeuvre (e.g. by a junction, carriage track,
roads crossing the direction of travel, etc.)
❒In the case of parking manoeuvres on roads on a
gradient, the performance of the system could
be inferior and it may deactivate.
117GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

REPLACING EXTERIOR BULBSFor the type of bulb and power rating, see
“Changing a bulb".
FRONT LIGHT UNITS
These contain the bulbs for the side lights/day
lights (DRL), dipped beams, main beams and
direction indicators. The bulbs are arranged
as follows fig. 129:ASide lights/daytime running lights and main
beam headlightsBDipped beam headlightsCDirection indicatorsSIDE LIGHTS/DAY LIGHTS (DRL)
To change the bulb, proceed as follows:
❒remove cover A fig. 129;
❒remove snap-fitted bulb holder B fig. 130,
remove the bulb C and replace it;
❒refit the new bulb then reinsert the bulb holder
B in its housing;
❒then refit the cover A fig. 129.fig. 129
L0F0033
fig. 130
L0F0069
195GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove cover A fig. 129;
❒turn the connector unit and the bulb holder B
fig. 131 anticlockwise;
❒remove the bulb C from connector D and
replace it;
❒refit the new bulb on the connector making sure
that it is locked correctly, then reinsert the
connector unit and the bulb holder B in
its housing;
❒then refit the cover A fig. 129.DIPPED BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒remove cover B fig. 129;
❒turn the snap-fitted bulb holder unit C fig. 132
anticlockwise, remove bulb D and replace it;
❒refit the new bulb then reinsert the bulb holder
unit C in its housing;
❒then refit the cover B fig. 129.
fig. 131
L0F0068
fig. 132
L0F0070
196
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

SUSPENSIONVersions Front Rear
0.9 TwinAir 85 HP
Independent, MacPherson type with
lower transversal wishbones secured to
an auxiliary crossmemberInterconnected wheels by means of tor-
sion beam 1.2 8V 69 HP
1.3 16V MultiJetSTEERINGVersions Turning circle (m) Type
0.9 TwinAir 85 HP9.4
Rack and pinion with electric power
steering 1.2 8V 69 HP9.4
1.3 16V MultiJet9.4
247GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCETECHNICAL
SPECIFICATIONSINDEX

Cruise control....................... 62D
ashboard........................... 3
Daytime running lights
(DRL)
– "Daytime Running
Lights" ............................ 54
Diesel filter ......................... 2
Dipped beam headlights
– bulb replacement............ 196
– control ............................. 55
Dipped headlights
– bulb replacement............ 196
– control ............................. 55
Direction indicators
– bulb replacement............ 197
– control ............................. 56
Display................................. 7
– Control buttons................ 10
Doors ................................... 79
– Door lock/unlock ............. 79
DPF (particulate filter) ....... 128
Driving style ....................... 159
DRLs (Daytime Running
Lights) ............................... 54
Dualdrive (electric power
steering) ............................ 104Dualdrive (electric power
steering) ............................ 104
Dusk sensor.......................... 55
Electric windows ............. 83-84
Engine codes....................... 243
Engine compartment
– checking fluid levels ....... 223
– opening/closing ............... 90
– washing .......................... 238
Engine coolant
temperature indicator ......... 6
Engine
– Engine cooling system
fluid level ....................... 228
– identification codes......... 243
– marking ......................... 242
– technical specifications ... 244
Engine oil
– consumption................... 227
– level check...................... 227
– specifications .................. 260
Environment protection ...... 128
EOBD system...................... 104
ESC (system) ....................... 96
External lights...................... 54
Extinguisher......................... 76
Fitting "Universal" child
seat ................................... 140
Fix&Go Automatic Kit ........ 185
Fluids and lubricants
(specifications) .................. 260
Fog lights............................ 198
Follow me home (device) ..... 57
Front roof light
– bulb replacement............ 201
– control ............................. 65
Fuel consumption ............... 263
Fuel level gauge ................... 6
Fuse boxes (location) .......... 206
Fuses
– Dashboard fuse box ........ 208
– Engine compartment
fuse box.......................... 206
– fuse list........................... 210
– Luggage compartment
fuse box.......................... 20
– replacing fuses................ 204
307GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONSINDEX
Gearbox (use of)................. 157
Gear Shift Indicator
(system) ............................. 9
Glove compartment light
– bulb replacement............ 2049 29