2013 INFINITI QX56 check engine

The following statement is required to be provided by
regulations of the California Air Resources Board.
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board is pleased to explain
the emission control system warranty on your 2013
vehicle. In California, new motor vehicles must be de-
signed, built and equipped to meet the State’s stringent
anti-smog standards. Nissan
2must warrant the emis-
sion control system on your vehicle for the periods of
time listed below provided there has been no abuse,
neglect or improper maintenance of your vehicle.
Your emission control system may include parts such as the
fuel-injection system, the ignition system, catalytic con-
verter and engine computer. Also included may be hoses,
belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, Nissan will repair your
vehicle at no cost to you including diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE
For 4 years or 60,000 miles (whichever occurs first):
1. If your vehicle fails a Smog Check inspection, all necessary repairs and adjustments will be made by
Nissan to ensure that your vehicle passes the in-
spection. This is your emission control system PER-
FORMANCE WARRANTY.
2. If any emission-related part on your vehicle is de- fective, the part will be repaired or replaced by
Nissan. This is y our short-term em ission control
system DEFECTS WARRANTY. For 7 years or 70,000 miles (whichever occurs first):
If an emission-related part listed in this warranty book-
let specially noted with coverage for 7 years or 70,000
miles is defective, the part will be repaired or replaced
by Nissan. This is your long term emission control sys-
tem DEFECTS WARRANTY.
OWNER’S WARRANTY R
ESPONSIBILITIES
As the vehicle owner, you are responsible for the perfor-
mance of the required maintenance listed in your Own-
er’s Manual. Nissan recommends that you retain all
receipts covering maintenance on your vehicle, but
Nissan cannot deny warranty solely for the lack of re-
ceipts or for your failure to ensure the performance of all
scheduled maintenance.
You are responsible for presenting your vehicle to an
Infiniti retailer as soon as a problem exists. The war-
ranty repairs should be completed in a reasonable
amount of time, not to exceed 30 days.
As the vehicle owner, you should also be aware that
Nissan may deny you warranty coverage if your vehicle
or a part has failed due to abuse, neglect, improper
maintenance or unapproved modifications.
If you have any questions regarding your warranty rights
and responsibilities, you should contact Infiniti’s Con-
sumer Affairs Department at 1-800- 662-6200 or the
California Air Resources Board at 9528 Telstar Avenue,
El Monte CA 91731.
The following is Nissan’s1new vehicle emission control
warranty statement for vehicles certified for sale in Califor- nia and sold for registration as a new vehicle in California,
Connecticut, Maine, Maryland, Massachusetts, New Jer-
sey, Oregon, Pennsylvania, Rhode Island, Vermont, or
Washington only.
EMISSIONS DEFECTS WARRANTY
WHAT IS COVERED
NISSAN*warrants that your vehicle was designed, built
and equipped to conform with all applicable requirements
of the California Air Resources Board. This warranty covers
any part which affects app licable regulated emission(s).
Exceptions to this warranty are listed below under the
caption “WHAT IS NOT COVERED.”
HOW LONG IS THE WARRANTY
This warranty is for 4 years or 60,000 miles, whichever
occurs first. Additionally, the components listed under
the caption “Long-Term Em ission System Defects War-
ranty Parts List” are covered for 7 years or 70,000 miles,
whichever occurs first, except that the catalytic convert-
er(s) and engine control module (ECM) are warranted for
8 years or 80,000 miles, whichever occurs first. The
warranty begins the date the vehicle is delivered to the
first retail buyer or put into use, whichever is earlier.
Some items require schedule d replacement before 60,000
miles. These items are warranted only up to the replace-
ment interval. The replacement intervals are outlined in the
maintenance instructions in your Owner’s Manual.
(Continued on next page)
1 These warranties apply to all Calif ornia emission2013 Infiniti vehicles sold for registration as new vehicles in California, Connecticut, Maine, Maryland, Massachusetts, New Jersey, Oregon,
Pennsylvania, Rhode Island, Vermont, or Washington only.
2 Nissan indicates Nissan North America, Inc., P.O. Box 685003, Franklin, TN 37068-5003 which distributes Infiniti vehicles in the United States.
2013 INFINITI CALIFORNIA VEHICLE EMISSION CONTROL WARRANTIES111

DON’T OVERLOAD YOUR VEHICLE OR TIRES
Check your vehicle owner’s manual to determine the
load limits. Overloading your vehicle places stress on
your tires and other critical vehicle components. Over-
loading a vehicle can cause poor handling, increased
fuel consumption and may causetire failure. Overload-
ing your tires can result in severe cracking, component
separation or blowout.
Never fit your vehicle with new tires that have less load
capacity than shown on the vehicle tire placard and
remember that optimum rim width is important for
proper tire load distribution and function.
The maximum load capacity stamped on the sidewalls
of P-Metric tires is reduced by 10% when used on a light
truck, utility vehicle or trailer. Never fit P-Metric tires to
light trucks that specify LT-type replacement tires.
DON’T SPIN YOUR TIRES EXCESSIVELY
Avoid excessive tire spinning when your vehicle is stuck in
snow, ice, mud or sand. The centrifugal forces generated
by a free-spinning tire/wheel assembly may cause sud-
den tire explosion resulting in vehicle damage and/or
serious personal injury to you or a bystander. Never ex-
ceed 35 mph/55 km/h, as indicated on your speedom-
eter. Use a gentle backward and forward rocking motion
to free your vehicle for continued driving. Never stand
near or behind a tire spinning at high speeds. For ex-
ample, while attempting to push a vehicle that is stuck or
when an on-the-car spin balance machine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when they reach two
thirty-seconds of an inch (2/32) remaining tread depth. All new tires have treadwear indicators which appear as
smooth banks in the tread grooves when they wear to
the two thirty-seconds of an inch (2/32) level. Many wet
weather accidents result from skidding on bald or nearly
bald tires. Excessively w
orn tires are also more suscep-
tible to penetrations.
DO CHECK YOUR TIRES FOR DAMAGE
Frequent (at least monthly) inspection of your tires for
signs of damage and their general condition is impor-
tant for safety. If you have any questions, have your tire
retailer inspect them. Impacts, penetrations, cracks,
knots, bulges or air loss always require tire removal and
expert inspection. Never perform a temporary repair or
use an inner tube as a substitute for a proper repair.
Only qualified persons should repair tires.
PROPER TIRE REPAIR
NOTE: Goodyear and Dunlop do not warrant any inspec-
tion or repair process. The repair is entirely the respon-
sibility of the repairer and should be made in accor-
dance with established Rubber Manufacturers
Association (RMA) procedures.
THE CONVENIENCE (TEMPORARY) SPARE
The Convenience (Temporary) Spare is designed, built,
and tested to the high engineering standards set by
North America’s leading car manufacturers and to
Goodyear and Dunlop’s own high standards of quality
control. It is designed to take up a minimum of storage
space and, at the same time, fulfill the function of a
spare tire when needed. The spare is kept in its storage space, fully inflated at 60 psi. To be sure it is always
ready for use, the air pressure should be checked on a
regular basis.
The Convenience (Temporary) Spare can be used in
combination with the original tires on your vehicle. You
can expect a tire tread life of up to 3,000 miles (4,800
kilometers), depending on road conditions and your
driving habits. To conserve tire tread life, return the
spare to the storage area as soon as it is convenient to
have the standard tire repaired or replaced.
The Convenience (Temporary) Spare weighs less than a
standard tire so
it’s easier to handle. It also helps re-
duce the total car weight which contributes to fuel
economy.
The wheels used with the Convenience (Temporary)
Spare are specifically designed for use with high pres-
sure spares and should never be used with any other
type tire.
DON’T ATTEMPT TO MOUNT YOUR OWN TIRES
Serious injury or Death may result from explosion of
tire/ rim assembly due to improper mounting proce-
dures. Follow tire manufacturer’s instructions and
match tire diameter to rim diameter. Mount light truck
radials on rims approved for radial service. Do not apply
bead sealer. This can inhibit bead seating. Lubricate
beads and tire rim (including tube or flap) contact sur-
faces. Lock assembly on mounting machine or place in
safety cage. STAND BACK and never exceed 40 psi to
seat beads. Never use a volatile substance or a rubber
“donut” (also known as a bead expander or “O-Ring”) to
aid bead seating. Only specially-trained persons should
mount tires.
(Continued on next page)
28 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY

HARD BRAKING
You must inspect your tires after any hard braking cir-
cumstances or after tires have slid on the pavement.
This can cause a flat spot in a section of the tire tread.
TIRE SPINNING
Never spin your tires above a speedometer reading of
35 mph (55 km/h) if your vehicle becomes stuck. The
centrifugal force generated by the free spinning
tire/wheel assembly may cau se a sudden tire explo-
sion, resulting in vehicle damage and/or serious per-
sonal injury or death. Never allow anyone to stand near
or behind a tire spinning at high speed while attempting
to push a vehicle that is stuck. When in mud, sand,
snow, ice or other slippery conditions, do not indulge in
excessive wheel spin. In such conditions, with auto-
matic tran smission vehicles , by accelerating the engine
excessively, it is possible to spin one of the drive tires
beyond its speed capability. This is also true when bal-
ancing a drive tire/wheel assembly using the engine of
the vehicle to spin the wheel.
TIRE TREAD
Tires must be replaced when the depth of the tread
reaches 2/32 inch (1.6 mm). Tires are manufactured
with tread wear indicators molded into the tire grooves
which indicate tread wearout. As tires approximate
2/32 inch (1.6 mm) wearout, the tread gauge becomes
thinner and more vulnerable to the effects of road haz-
ards. Also, worn tires are more subject to hydroplaning,
which can cause loss of control. Therefore, visual tire
inspection becomes more crucial as the tires wear out.
WORN TIRES
Never drive on worn tires. Tires should be replaced by
trained personnel when 2/32nds of an inch tread depth
remains, as indicated by the tread wear indicators molded
into the tread grooves. In most states, it is illegal to drive
with less than 2/32nds of an inch of tread remaining.
TIRE MIXING
For best performance select tires similar in size and load
rating to the original equipment tires. It is recom-
mended that the same size and type of tire be used on
all four wheel positions. In certain tires, casing ply ma-
terial and ply construction may vary as indicated on the
sidewall of the tire. When changing or replacing tires, it
is preferred that all four tires are the same construction
type (i.e., High Performance, All Season, Mud & Snow)
and construction (Radial or Bias Ply). Before mixing tires
of different types on a vehicle in any configuration, be
sure to check the vehicle owner’s manual for its recom-
mendations.
Tires which meet the Rubber Manufacturer’s Associa-
tion (RMA) definition of mud and snow tires are marked
M/S, M+S, M&S. On such tires, this designation is
molded into the sidewall. Tires without this notation are
not recommended for mud and/or snow driving.
If snow tires are needed, it is necessary to select tires
equivalent in size and load rating to the original equip-
ment tires. Always fit performance snow tires in sets of
four (4) for optimum mud & snow traction and mainte-
nance of vehicle handling characteristics. If you do not,
it may adversely affect the safety and handling of your
vehicle. It is also important to check the vehicle owner’s
manual before mixing or matching tires on 4-wheel drive
vehicles as this may require special precautions. Please refer to your Owner’s Manual for more informa-
tion on tire replacement precautions.
TIRE ROTATION
Tires on your Nissan vehicle should be rotated every
7,500 miles or as irregular wear develops. If irregular
wear becomes apparent or if the wear rate on the tires is
perceptibly uneven, the tires should be rotated in such a
way to alleviate the problem. Check your vehicle for any
mechanical problems and correct if necessary. Any rota-
tion pattern or procedure may be followed including
those indicated in the Owner’s Manual. Some tires have
arrows on the sidewall showing the direction in which
the tire should turn. When rotating this type of tire, care
must be taken to maintain the proper turning direction
as indicated by the arrows.
Some vehicles have different
tire sizes specified for front and rear axles. Tires on these
vehicles should not be rotated side to side (unless they
are non-directional) . Where a temporary type spare tire
is available, it should not be included in the tire rotation
schedule. Such tires are intended for temporary use
only.
REPLACING TWO TIRES
If your vehicle was originally equipped with four tires
that were the same size and you are only replacing two
of the four tires, install the new tires on the rear axle.
Placing new tires on the front axle may cause loss of
vehicle control in some driving conditions and cause an
accident and personal injury.
(Continued on next page)
48 IMPORTANT TIRE SAFETY INFORMATION1