DON’T OVERLOAD YOUR VEHICLE OR TIRES
Check your vehicle owner’s manual to determine the
load limits. Overloading your vehicle places stress on
your tires and other critical vehicle components. Over-
loading a vehicle can cause poor handling, increased
fuel consumption and may causetire failure. Overload-
ing your tires can result in severe cracking, component
separation or blowout.
Never fit your vehicle with new tires that have less load
capacity than shown on the vehicle tire placard and
remember that optimum rim width is important for
proper tire load distribution and function.
The maximum load capacity stamped on the sidewalls
of P-Metric tires is reduced by 10% when used on a light
truck, utility vehicle or trailer. Never fit P-Metric tires to
light trucks that specify LT-type replacement tires.
DON’T SPIN YOUR TIRES EXCESSIVELY
Avoid excessive tire spinning when your vehicle is stuck in
snow, ice, mud or sand. The centrifugal forces generated
by a free-spinning tire/wheel assembly may cause sud-
den tire explosion resulting in vehicle damage and/or
serious personal injury to you or a bystander. Never ex-
ceed 35 mph/55 km/h, as indicated on your speedom-
eter. Use a gentle backward and forward rocking motion
to free your vehicle for continued driving. Never stand
near or behind a tire spinning at high speeds. For ex-
ample, while attempting to push a vehicle that is stuck or
when an on-the-car spin balance machine is in use.
DO CHECK YOUR TIRES FOR WEAR
Always remove tires from service when they reach two
thirty-seconds of an inch (2/32) remaining tread depth. All new tires have treadwear indicators which appear as
smooth banks in the tread grooves when they wear to
the two thirty-seconds of an inch (2/32) level. Many wet
weather accidents result from skidding on bald or nearly
bald tires. Excessively w
orn tires are also more suscep-
tible to penetrations.
DO CHECK YOUR TIRES FOR DAMAGE
Frequent (at least monthly) inspection of your tires for
signs of damage and their general condition is impor-
tant for safety. If you have any questions, have your tire
retailer inspect them. Impacts, penetrations, cracks,
knots, bulges or air loss always require tire removal and
expert inspection. Never perform a temporary repair or
use an inner tube as a substitute for a proper repair.
Only qualified persons should repair tires.
PROPER TIRE REPAIR
NOTE: Goodyear and Dunlop do not warrant any inspec-
tion or repair process. The repair is entirely the respon-
sibility of the repairer and should be made in accor-
dance with established Rubber Manufacturers
Association (RMA) procedures.
THE CONVENIENCE (TEMPORARY) SPARE
The Convenience (Temporary) Spare is designed, built,
and tested to the high engineering standards set by
North America’s leading car manufacturers and to
Goodyear and Dunlop’s own high standards of quality
control. It is designed to take up a minimum of storage
space and, at the same time, fulfill the function of a
spare tire when needed. The spare is kept in its storage space, fully inflated at 60 psi. To be sure it is always
ready for use, the air pressure should be checked on a
regular basis.
The Convenience (Temporary) Spare can be used in
combination with the original tires on your vehicle. You
can expect a tire tread life of up to 3,000 miles (4,800
kilometers), depending on road conditions and your
driving habits. To conserve tire tread life, return the
spare to the storage area as soon as it is convenient to
have the standard tire repaired or replaced.
The Convenience (Temporary) Spare weighs less than a
standard tire so
it’s easier to handle. It also helps re-
duce the total car weight which contributes to fuel
economy.
The wheels used with the Convenience (Temporary)
Spare are specifically designed for use with high pres-
sure spares and should never be used with any other
type tire.
DON’T ATTEMPT TO MOUNT YOUR OWN TIRES
Serious injury or Death may result from explosion of
tire/ rim assembly due to improper mounting proce-
dures. Follow tire manufacturer’s instructions and
match tire diameter to rim diameter. Mount light truck
radials on rims approved for radial service. Do not apply
bead sealer. This can inhibit bead seating. Lubricate
beads and tire rim (including tube or flap) contact sur-
faces. Lock assembly on mounting machine or place in
safety cage. STAND BACK and never exceed 40 psi to
seat beads. Never use a volatile substance or a rubber
“donut” (also known as a bead expander or “O-Ring”) to
aid bead seating. Only specially-trained persons should
mount tires.
(Continued on next page)
28 GOODYEAR/DUNLOP TIRE LIMITED WARRANTY
