2013 Hyundai Genesis Coupe turn signal

Maintenance
76
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
✽✽ NOTICE
After heavy, driving rain or washing, headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside. This is sim-
ilar to the condensation on your win-
dows inside your vehicle during the rain
and doesn’t indicate a problem with
your vehicle. If the water leaks into the
lamp bulb circuitry, we recommend thatthe system be checked by an authorized
HYUNDAI dealer.
Headlight, position light, turn sig-
nal light, front fog light bulbreplacement
(1) Front turn signal light
(2) Headlight (High)
(3) Headlight (Low)
(4) Front fog light
(5) Position light/DRL (if equipped)
WARNING - Working on
the lights
Prior to working on the light, firmly
apply the parking brake, ensure
that the ignition switch is turned tothe LOCK position and turn off the
lights to avoid sudden movement
of the vehicle and burning your fin-
gers or receiving an electric shock.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattagerating. Otherwise, it may causedamage to the fuse or electric wiring system.
CAUTION
If you don’t have necessary tools,the correct bulbs and the expertise,
we recommend that you consult anauthorized HYUNDAI dealer. Inmany cases, it is difficult to replace vehicle light bulbs because other
parts of the vehicle must beremoved before you can get to thebulb. This is especially true if you
have to remove the headlightassembly to get to the bulb(s).Removing/installing the headlightassembly can result in damage to
the vehicle.
OBK072026

779
Maintenance
✽✽NOTICE
If the headlight aiming adjustment is
necessary after the headlight assembly is
reinstalled, we recommend that you con-
sult an authorized HYUNDAI dealer.
❋❋ Traffic Change (For Europe)
The low beam light distribution is asym-
metric.
If you go abroad to a country with oppo-
site traffic direction, this asymmetric part
will dazzle oncoming car driver. To pre-
vent dazzle, these headlamps are
designed not to dazzle opposite drivers.
So, you need not change your head-
lamps in a country with opposite trafficdirection.
Turn signal light bulb replacement
8. Remove the socket from the assembly by turning the socket counter clock-
wise until the tabs on the socket align
with the slots on the assembly.
9. Remove the bulb from the socket by pressing it in and rotating it until the
tabs on the bulb align with the slots in
the socket. Pull the bulb out of the
socket.
10. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
11. Install the socket into the assembly by aligning the tabs on the socket
with the slots in the assembly. Push
the socket into the assembly and turn
the socket clockwise.
Front fog light bulb replacement
1. Turn the steering wheel fully. (If youwant to replace driver side fog lamp,
turn the steering wheel to the front
passenger side.)
2. Open the hood.
3. Disconnect the negative battery cable.
4. Loosen the retaining bolt on the serv- ice cover. And then pull down the serv-
ice cover.
5. Remove the fog light bulb cover by turning it counter clockwise.
OBK079046OBK072056

Maintenance
86
7
Side repeater light bulb replace- ment (if equipped)
If the light is not operating, we recom-
mend that you checked an authorized
HYUNDAI dealer. Rear combination light bulb replacement
(1) Rear fog light (if equipped,
driver side only) or Back-up light
(2) Rear turn signal light (3) Stop and tail light 1. Open the trunk lid.
2. Remove the service cover by pulling
out the service cover.
OBK049023OBK072028OBK072029

787
Maintenance
3. Loosen the assembly retaining nuts.
4. Remove the rear combination lightassembly from the body of the vehicle.
Turn signal light
5. Remove the socket from the assemblyby turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb from the socket by pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
8. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
Back up or rear fog* 1
light
5. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
6. Remove the bulb by pulling it out.
7. Inset a new bulb by inserting it into the socket.
8. Install the socket in the assembly by aligning the tabs on the socket with the
slots in the assembly. Push the socket
into the assembly and turn the socket
clockwise.
* 1
: if equipped, rear fog light only the driver side
OBK072063
Back up or rear fog Turn signal
OBK072061
OBK072062

Specifications & Consumer information
2
8
DIMENSIONS BULB WATTAGE
Item mm (in)
Overall length 4,630 (182.2)
Overall width 1,865 (73.4)
Overall height 1,385 (54.5)
Front tread 1,605 (63.2) / 1,601 (63.0)*1
Rear tread 1,625 (64.0) / 1,621 (63.8)*1
Wheelbase 2,820 (111)
ENGINE
Item Gasoline 2.0 Gasoline 3.8
Displacement [cc(cu.in)] 1,998
(121.9) 3,778
(230.5)
Bore x Stroke [mm(in)] 86 x 86
(3.38 x 3.38) 96 x 87
(3.78 x 3.42)
Firing order 1-3-4-2 1-2-3-4-5-6
No. of cylinders 4, In-line 6, V-Type
Light Bulb Wattage Bulb type
Headlights (Low) 55 or
35 (HID) H7*
1
Headlights (High) 55 H7LL
Front turn signal lights 21 PY21WLL
Front fog lights 35 H8L
Front position lightsLEDLED
Daytime running lights*LEDLED
Rear fog light* (Driver side only) 21 H21W
Stop and tail lights LED LED
Rear turn signal lights 21 P21WL
Back-up lights 16 W16W
High mounted stop light* LED LED
License plate lights 5 W5WL
Map lamps 10 W10W
Luggage lamp 5 FESTOON
Glove box lamp 5 FESTOON
Vanity mirror lamps* 5 FESTOON
Side repeater lights* LED LED
* : if equipped * 1
: For Europe - H7HPLL
Except Europe - H7LL
*
1
: with R19 tire