2013 Hyundai Genesis Coupe ABS

529
Driving your vehicle
✽✽NOTICE
When you jump start your vehicle
because of a drained battery, the engine
may not run as smoothly and the ABSwarning light may turn on at the same
time. This happens because of the lowbattery voltage. It does not mean yourABS is malfunctioning.

541
Driving your vehicle
Hazardous driving conditions
When hazardous driving conditions are
encountered such as water, snow, ice,
mud, sand, or similar hazards, followthese suggestions:
Drive cautiously and allow extra dis-tance for braking.
Avoid sudden movements in braking or steering.
When braking with non-ABS brakes pump the brake pedal with a light up-
and-down motion until the vehicle isstopped. If stalled in snow, mud, or sand, use
second gear. Accelerate slowly to
avoid spinning the drive wheels.
Use sand, rock salt, tire chains, or other non-slip material under the drive
wheels to provide traction when stalled
in ice, snow, or mud. Rocking the vehicle
If it is necessary to rock the vehicle to free
it from snow, sand, or mud, first turn the
steering wheel right and left to clear the
area around your front wheels. Then, shift
back and forth between 1st (First) and R
(Reverse) in vehicles equipped with a
manual transmission or R (Reverse) and
any forward gear in vehicles equipped
with an automatic transmission. Do not
race the engine, and spin the wheels as
little as possible. If you are still stuck after
a few tries, have the vehicle pulled out by
a tow vehicle to avoid engine overheating
and possible damage to the transmission.
SPECIAL DRIVING CONDITIONS
OBK052019L
WARNING -
ABS
Do not pump the brake pedal on a
vehicle equipped with ABS.
WARNING - Downshifting
Downshifting with an automatic
transmission, while driving on slip-
pery surfaces can cause an acci-
dent. The sudden change in tirespeed could cause the tires to skid.
Be careful when downshifting on
slippery surfaces.
CAUTION
Prolonged rocking may cause engine over-heating, transmission
damage or failure, and tire damage.

611
What to do in an emergency
7. Place the jack at the front or rearjacking position closest to the tire
you are changing. Place the jackat the designated locations under
the frame. The jacking positions
are plates welded to the frame
with two tabs and a raised dot to
index with the jack. 8. Insert the jack handle into the jack
and turn it clockwise, raising the
vehicle until the tire just clears the
ground. This measurement is
approximately 30 mm (1.2 in).
Before removing the wheel lug
nuts, make sure the vehicle is sta-
ble and that there is no chance for
movement or slippage. 9. Loosen the wheel nuts and
remove them with your fingers.Slide the wheel off the studs and
lay it flat so it cannot roll away. To
put the wheel on the hub, pick up
the spare tire, line up the holeswith the studs and slide the wheel
onto them. If this is difficult, tip thewheel slightly and get the top holein the wheel lined up with the top
stud. Then jiggle the wheel back
and forth until the wheel can be
slid over the other studs.
WARNING - Jack location
To reduce the possibility of
injury, be sure to use only the
jack provided with the vehicle
and in the correct jack position;
never use any other part of the
vehicle for jack support.
OBK069022OBK069015

Maintenance
58
7
Compact spare tire replacement
(if equipped)
A compact spare tire has a shorter
tread life than a regular size tire.
Replace it when you can see the
tread wear indicator bars on the tire.The replacement compact spare tire
should be the same size and design
tire as the one provided with your
new vehicle and should be mountedon the same compact spare tire
wheel. The compact spare tire is notdesigned to be mounted on a regular
size wheel, and the compact spare
tire wheel is not designed for mount-
ing a regular size tire. Wheel replacement
When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim widthand offset.
✽✽
NOTICE
The front tire size is different from
the rear tire size. So when you rotate
tires, check the tire and wheel size.
(Continued)
Using tires and wheel other than the recommended sizes
could cause unusual handling
characteristics and poor vehi-
cle control, resulting in a seri-ous accident.
Wheels that do not meet HYUNDAI’s specifications
may fit poorly and result in
damage to the vehicle or
unusual handling and poor
vehicle control.
The ABS works by comparing the speed of the wheels. Tire
size can affect wheel speed.
When replacing tires, all 4
tires must use the size origi-
nally supplied with the vehi-
cle. Using tires of a different
size can cause the ABS (Anti-
lock Brake System) and ESP
(Electronic Stability Program)
to work irregularly.
WARNING
A wheel that is not the correct
size may adversely affect wheel
and bearing life, braking and
stopping abilities, handling
characteristics, ground clear-
ance, body-to-tire clearance,
snow chain clearance,speedometer and odometer cal-
ibration, headlight aim and
bumper height.

Maintenance
70
7
Instrument panel (Driver’s side fuse panel)
Fuse NameSymbolFuseratingCircuit Protected
AUDIO15AAudio, Multi Gauge, Multi Monitor
DRV P/SEAT30ADriver Seat Manual Switch, Driver Lumbar Support Switch
HAZARD15ABCM
PDM 125APDM
ROOM LP10ADriver/Passenger Door Lamp, Trunk Room Lamp, Driver/Passenger Door Scuff Lamp,
Vanity Lamp LH/RH, Map Lamp
C/LIGHTER15AFront Power Outlet
MEMORY 110ABCM, Data Link Connector, Auto Light & Photo Sensor, Ignition Key ILL. & Door Warning
Switch, Instrument Cluster (IND. MICOM), A/C Control Module, Power Outside MirrorSwitch
MEMORY 27.5ARF Receiver
ABS7.5AE/R Junction Box LH (Multi Purpose Check Connector), ESP Control Module, ESP & PAS/
Rear Fog Lamp Switch, Steering Angle Sensor
A/BAG IND7.5AInstrument Cluster (Air Bag IND.)
A/BAG15ASRS Control Module
B/UP LP15ABack-Up Lamp Switch, TCM, Transaxle Range Switch
MODULE 310AECM, PDM, Smart Key Control Module, Injector Drive Box (G6DJ)

773
Maintenance
Engine compartment main fuse panel
Fuse NameSymbolFuseratingCircuit Protected
MULTIFUSE
C/FAN60ACooling Fan (High) Relay, Cooling Fan (Low) Relay
B+160ASmart Junction Box (Fuse - F31/F32/F33/F34/F35, IPS 2, IPS Control Module)
BLOWER40ASmart Junction Box (Blower Relay)
ABS240AMultipurpose Check Connector, ESP Control Module
ABS140AMultipurpose Check Connector, ESP Control Module
ALT150AAlternator, MULTI FUSE - F1/F2/F3/F4/F5, Fuse - F12/F13/F14/F15/F18
RR HTD40ARR HTD Relay
B+260ASmart Junction Box (Fuse - F3/F4/F20/F21/F29/F30, IPS 1, ARISU 2, IPS Control Module)
B+360ASmart Junction Box (Leak Current Autocut Device Switch, Leak Current
Autocut Device Relay, Fuse - F1/F2/F5/F7/F8, ARISU 1, IPS Control Module)
FUSE
IG230AStart Relay, IG2 Relay, Ignition Switch
IG140AIG1 Relay, ACC Relay, Ignition Switch
S/ROOF FRT20ASunroof Control Module

Maintenance
78
7
Headlight bulb8. Remove the headlight bulb cover by
turning it counterclockwise.
9. Disconnect the headlight bulb socket- connector.
10. Remove the socket from the assem- bly by turning the socket counter-
clockwise until the tabs on the socket
align with the slots on the assembly.
11. Pull the bulb out of the socket.
12. Insert a new bulb into the socket.
13. Install the socket in the assembly by aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
14. Connect the headlight bulb socket- connector.
15. Install the headlight bulb cover by turning it clockwise.
(Continued)
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
Wear eye protection when chang- ing a bulb. Allow the bulb to cool
down before handling it.
OBK072045OHD076046
WARNING - Halogen bulbs
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never touchthe glass with bare hands.
Residual oil may cause the bulb
to overheat and burst when lit. A
bulb should be operated onlywhen installed in a headlight.
(Continued)

779
Maintenance
✽✽NOTICE
If the headlight aiming adjustment is
necessary after the headlight assembly is
reinstalled, we recommend that you con-
sult an authorized HYUNDAI dealer.
❋❋ Traffic Change (For Europe)
The low beam light distribution is asym-
metric.
If you go abroad to a country with oppo-
site traffic direction, this asymmetric part
will dazzle oncoming car driver. To pre-
vent dazzle, these headlamps are
designed not to dazzle opposite drivers.
So, you need not change your head-
lamps in a country with opposite trafficdirection.
Turn signal light bulb replacement
8. Remove the socket from the assembly by turning the socket counter clock-
wise until the tabs on the socket align
with the slots on the assembly.
9. Remove the bulb from the socket by pressing it in and rotating it until the
tabs on the bulb align with the slots in
the socket. Pull the bulb out of the
socket.
10. Insert a new bulb by inserting it into the socket and rotating it until it locks
into place.
11. Install the socket into the assembly by aligning the tabs on the socket
with the slots in the assembly. Push
the socket into the assembly and turn
the socket clockwise.
Front fog light bulb replacement
1. Turn the steering wheel fully. (If youwant to replace driver side fog lamp,
turn the steering wheel to the front
passenger side.)
2. Open the hood.
3. Disconnect the negative battery cable.
4. Loosen the retaining bolt on the serv- ice cover. And then pull down the serv-
ice cover.
5. Remove the fog light bulb cover by turning it counter clockwise.
OBK079046OBK072056