2013 Hyundai Genesis Coupe ignition

773
Maintenance
Engine compartment main fuse panel
Fuse NameSymbolFuseratingCircuit Protected
MULTIFUSE
C/FAN60ACooling Fan (High) Relay, Cooling Fan (Low) Relay
B+160ASmart Junction Box (Fuse - F31/F32/F33/F34/F35, IPS 2, IPS Control Module)
BLOWER40ASmart Junction Box (Blower Relay)
ABS240AMultipurpose Check Connector, ESP Control Module
ABS140AMultipurpose Check Connector, ESP Control Module
ALT150AAlternator, MULTI FUSE - F1/F2/F3/F4/F5, Fuse - F12/F13/F14/F15/F18
RR HTD40ARR HTD Relay
B+260ASmart Junction Box (Fuse - F3/F4/F20/F21/F29/F30, IPS 1, ARISU 2, IPS Control Module)
B+360ASmart Junction Box (Leak Current Autocut Device Switch, Leak Current
Autocut Device Relay, Fuse - F1/F2/F5/F7/F8, ARISU 1, IPS Control Module)
FUSE
IG230AStart Relay, IG2 Relay, Ignition Switch
IG140AIG1 Relay, ACC Relay, Ignition Switch
S/ROOF FRT20ASunroof Control Module

775
Maintenance
Engine compartment sub fuse panel
Fuse NameSymbolFuseratingCircuit Protected
B+50AFuse - F2/F3/F4
EMS30ARLY. 1 (Engine Control Relay)
F/PUMP20ARLY. 2 (Fuel Pump Relay)
ECU 110AG4KF/G6DA - ECM, TCM
G6DJ - ECM, TCM, Injector Drive Box
INJECTOR15A
G4KF - RLY. 2 (Fuel Pump Relay), Injector #1/#2/#3/#4
G6DA - RLY. 2 (Fuel Pump Relay), Injector #1/#2/#3/#4/#5/#6, ECM
G6DJ - RLY. 2 (Fuel Pump Relay), Fuel Pump Relay (Low), ECM
IGN COIL20AG4KF - Ignition Coil #1/#2/#3/#4, Condenser
G6DA/G6DJ - Ignition Coil #1/#2/#3/#4/#5/#6, Condenser #1/#2
ECU 220AG4KF - ECM
G6DJ - Injector Drive Box
SENSOR 110A
G4KF - Cooling Fan (High)/(Low) Relay, Oxygen Sensor (Up)/(Down)
G6DA - Cooling Fan (High)/(Low) Relay, ECM, Oxygen Sensor #1/#2/#3/#4, Mass Air Flow Sensor
G6DJ - Cooling Fan (High)/(Low) Relay, ECM, Oxygen Sensor #1/#2/#3/#4
SENSOR 215A
G4KF - Camshaft Position Sensor #1/#2, RCV Control Solenoid Valve, Immobilizer Module,Purge Control Solenoid Valve, Crankshaft Position Sensor, Oil Control Valve #1/#2
G6DA/G6DJ - ECM, Oil Control Valve #1/#2/#3/#4, Purge Control Solenoid Valve, Immobilizer Module

Maintenance
76
7
LIGHT BULBS
Use only the bulbs of the specified
wattage.
✽✽ NOTICE
After heavy, driving rain or washing, headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside. This is sim-
ilar to the condensation on your win-
dows inside your vehicle during the rain
and doesn’t indicate a problem with
your vehicle. If the water leaks into the
lamp bulb circuitry, we recommend thatthe system be checked by an authorized
HYUNDAI dealer.
Headlight, position light, turn sig-
nal light, front fog light bulbreplacement
(1) Front turn signal light
(2) Headlight (High)
(3) Headlight (Low)
(4) Front fog light
(5) Position light/DRL (if equipped)
WARNING - Working on
the lights
Prior to working on the light, firmly
apply the parking brake, ensure
that the ignition switch is turned tothe LOCK position and turn off the
lights to avoid sudden movement
of the vehicle and burning your fin-
gers or receiving an electric shock.
CAUTION
Be sure to replace the burned-out bulb with one of the same wattagerating. Otherwise, it may causedamage to the fuse or electric wiring system.
CAUTION
If you don’t have necessary tools,the correct bulbs and the expertise,
we recommend that you consult anauthorized HYUNDAI dealer. Inmany cases, it is difficult to replace vehicle light bulbs because other
parts of the vehicle must beremoved before you can get to thebulb. This is especially true if you
have to remove the headlightassembly to get to the bulb(s).Removing/installing the headlightassembly can result in damage to
the vehicle.
OBK072026

Maintenance
98
7
Do not operate the engine in confined
or closed areas (such as garages) any
more than what is necessary to move
the vehicle in or out of the area.
When the vehicle is stopped in an open area for more than a short time
with the engine running, adjust the
ventilation system (as needed) to draw
outside air into the vehicle.
Never sit in a parked or stopped vehi- cle for any extended time with the
engine running.
When the engine stalls or fails to start, excessive attempts to restart the
engine may cause damage to theemission control system.Operating precautions for catalytic
converters (if equipped)Your vehicle is equipped with a catalytic
converter emission control device.
Therefore, the following precautions
must be observed:
Make sure to refuel your vehicle according to the “Fuel requirements”suggested in section 1.
Do not operate the vehicle when there are signs of engine malfunction, such
as misfire or a noticeable loss of per-
formance.
Do not misuse or abuse the engine. Examples of misuse are coasting withthe ignition off and descending steep
grades in gear with the ignition off.
Do not operate the engine at high idle speed for extended periods (5 minutesor more).
Do not modify or tamper with any part of the engine or emission control sys-
tem. We recommend that the system
be inspected by an authorized
HYUNDAI dealer.
Avoid driving with a very low fuel level. If you run out of gasoline, it couldcause the engine to misfire and result
in excessive loading of the catalytic
converter.
Failure to observe these precautionscould result in damage to the catalytic
converter and to your vehicle.
Additionally, such actions could void your
warranties.
WARNING - Fire
A hot exhaust system can ignite flammable items under your vehi-
cle. Do not park, idle, or drive the
vehicle over or near flammable
objects, such as grass, vegeta-
tion, paper, leaves, etc.
The exhaust system and catalytic system are very hot while the
engine is running or immediately
after the engine is turned off.
Keep away from the exhaust sys-
tem and catalytic, you may get
burned.
Also, do not remove the heat sink
around the exhaust system, do
not seal the bottom of the vehicle
or do not coat the vehicle for cor-
rosion control. It may present a
fire risk under certain conditions.