2013 FORD MUSTANG tire pressure

WASHING YOUR VEHICLE
Note:Do not drive your vehicle through an automated, commercial car
wash due to the vehicle’s low ground clearance, tire width and track
width. Wash your vehicle by hand, or by using a touchless commercial
wash with no mechanical tracks on the floor. Do not use a commercial or
high pressure wand on the striped surfaces or stripe edges.
TRAILER TOWING
WARNING:Never tow a trailer with this vehicle. Your vehicle is
not equipped to tow. No towing packages are available through
an authorized dealer.
Driving your Boss302
10
2013 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

WHEELS
Your Boss302 is equipped with unique wheels matched to the tires.
These wheels are more susceptible to damage due to their diameter,
width and low profile tires. To avoid damage to your wheels:
•Maintain proper tire pressure (seeTiresin this supplement).
•Do not drive your vehicle through an automated, commercial car wash
due to the vehicle’s low ground clearance, tire width and track width.
Wash your vehicle by hand, or by using a touchless commercial wash
with no mechanical tracks on the floor.
•When installing wheels, always torque lug nuts to specification with a
torque wrench.
•Inspect your wheels for damage on a regular basis. If a wheel is
damaged, replace it immediately.
•In the event that you encounter an abnormally harsh impact, inspect
the outer edge of your wheels, both inside and out, for damage.
Operating at High Speeds
Your Boss302 is capable of high speeds and is equipped with tires
rated for the vehicle’s maximum speed, electronically limited to 155 mph
(250 km/h). Remember to drive safely, obey all traffic laws and only
operate your vehicle at high speeds at locations equipped and designed
to do so safely. Before operating your vehicle at high speeds:
•Ensure correct tire pressures (seeTiresin this supplement).
•Inspect wheels and tires for wear and damage. Replace any damaged
wheels or tires.
•Do not operate your vehicle at high speeds with more than two
passengers or while carrying cargo.
Wheel Lug Nut Torque Specifications
WARNING:When a wheel is installed, always remove any
corrosion, dirt or foreign materials present on the mounting
surfaces of the wheel or the surface of the wheel hub, brake drum or
brake disc that contacts the wheel. Make sure that any fasteners that
attach the rotor to the hub are secured so they do not interfere with
the mounting surfaces of the wheel. Installing wheels without correct
metal-to-metal contact at the wheel mounting surfaces can cause the
wheel nuts to loosen and the wheel to come off while the vehicle is in
motion, resulting in loss of control.
Tire Information
13
2013 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

The Mustang Boss 302 Laguna Seca package includes D.O.T. approved
ultra high-performance summer tires with track capability. The rubber
compounds used in these tires lose flexibility and may develop surface
cracks in the tire tread area at temperatures below 20°F (-7°C). Always
store your tires indoors at temperatures above 20°F (-7°C). If the tires
have been subjected to 20°F (-7°C) or less, warm them in a heated space
to at least 40°F (5°C) for at least 24 hours before installing them on a
vehicle, or moving the vehicle with the tires installed, or checking tire
inflation. Do not place tires near heaters or heating devices used to
warm the room where the tires are stored. Do not apply heat or blow
heated air directly on the tires. Always inspect the tires after storage
periods and before use as outlined in the owner’s manual. Ford does not
recommend using the high performance summer tires on your Boss 302
or Boss 302 Laguna Seca edition when temperatures drop to
approximately 40
oF(5oC) or below, or in snow/ice conditions.
WARNING:If equipped with the Laguna SecaPackage, never
drive with these tires in any wet conditions (rain, snow, ice, etc.)
because they cannot channel water away and will slide risking serious
injury.
•Note:Do not use tire chains on the original wheels and tires of your
vehicle. The use of any type of tire chain on these tires may damage
your vehicle.
•Always maintain your tire pressures according to the tire information
placard on the driver’s door jamb, using an accurate gauge.
•Tire pressures are specified “cold” and should be checked after the
vehicle has been parked for at least 3 hours. Do not reduce pressure
of warm tires.
•Check your tire pressure often to maintain it properly. Tire pressure
can diminish over time and fluctuate with temperature.
•Do not overload your vehicle. Maximum vehicle and axle weights are
listed on the tire information placard.
•Extra caution should be taken when operating the vehicle near its
maximum load, including assuring proper tire pressure and reducing
speeds.
•Extra caution should be taken when operating on rough roads to avoid
impacts that could cause tire damage.
•In the event that you encounter an abnormally harsh impact, inspect
your tires for damage.
Tire Information
15
2013 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

•Boss302 (non-Laguna Seca)
tire rotation
(front tires at the top of the
diagram)
•Sometimes irregular tire wear can be corrected by rotating the tires.
•If your tires show uneven wear, ask an authorized dealer to check for
and correct any wheel misalignment, tire imbalance or mechanical
problem involved before tire rotation.
•After having your tires rotated, inflation pressure must be checked
and adjusted to the vehicle requirements.
Tire Information
17
2013 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)

•For track sessions, it is recommended to run 41 psi (283 kPa) hot for
the original equipment manufacturer tires, front and rear.
•Depending on track temperature, ambient temperature and driving
style, you may need to reduce the starting tire pressure by as
much as 4 psi (27 kPa).
•The starting pressure may be lower in the rear tires relative to the
front tires to achieve 41 psi (283 kPa) hot.
•Reset tire pressures to placard recommended pressures before
leaving the track.
•For improved track performance, Ford recommends
,
available through Ford Racing. See your local Ford dealer or go to
http://www.trackey.ford.com for more information (M-14204-MBTKA).
•Your Boss302 is equipped from the factory with Brembo 4-piston
front calipers and unique, high-performance rear brake pads that will
provide excellent performance under normal driving conditions. Ford
recommends the following bedding procedure for race track driving be
followed.
Brake burnishing procedure for race track driving
If the vehicle has to be driven on a track (racing) or in severe driving
conditions, the following steps must be performed on a closed course,
not on public roads:
•Burnish: 30 burnish stops at 60-0 mph (96-0 km/h), 0.4g deceleration,
one mile (1.6 km) between stops. If the vehicle has more than
200 miles (322 km) on the brakes, skip this step and proceed to the
Fade stops.
•Fade: 20 fade stops, at 65-0 mph (105-0 km/h), 0.85g deceleration or
just below ABS activity, no dwell between stops
•Cool down: Minimum of five mile (8 km) cool down route, if on public
roads (no brakes) run at 60 mph (96 km/h)
•Recovery: 30 recovery stops at 60-0 mph (96-0 km/h), 0.4 g
deceleration, one mile (1.6 km) between stops
•Cool down: Minimum of five mile (8 km) cool down route, if on public
roads (no brakes) run at 60 mph (96 km/h)
Track Use Preparation
29
2013 05+ Mustang(197)
Supplement, 1st Printing
USA(fus)