2013 FORD FOCUS transmission

Introduction
2
Welcome 2
Breaking-in your vehicle 4
Focus ST Unique Features
5
Gauges 6
Driving Your Focus ST
10
Transmission operation 10
AdvanceTrac12
Engine over-rev 13
Wheels and Tires
14
Wheels 14
Wheel lug nut torque 14
Tire information 15
Roadside Emergencies
18
Wrecker towing 18
Maintenance
19
Under hood overview 19
Capacities and Specifications
21
Engine specifications 21
Technical specifications 25
Transmission code designation 27
Warranty Coverage
28
The information contained in this publication was correct at the time of going to
print. In the interest of continuous development, we reserve the right to change
specifications, design or equipment at any time without notice or obligation. No
part of this publication may be reproduced, transmitted, stored in a retrieval
system or translated into any language in any form by any means without our
written permission. Errors and omissions excepted.
© Ford Motor Company 2012
Table of Contents
1
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

Oil pressure gauge
Indicates engine oil pressure.
During normal driving the indicated oil pressure will vary with engine
speed, the pressure rising as engine speed rises and dropping as engine
speed drops.
If the engine oil pressure drops below the normal range, the oil pressure
gauge pointer will drop into the red section of the gauge scale and the
engine oil pressure warning lamp in the main instrument cluster will
illuminate. Stop the vehicle as soon as safely possible and switch off the
engine immediately. Check the oil level and add oil if needed.
Vehicle Specifications
Item Description
TransmissionGFT MMT6 6-speed manual with 240 mm clutch and
dual mass flywheel
Gear ratiosGear Ratio Final Drive
1st 3.231 4.063
2nd 1.952 4.063
3rd 1.321 4.063
4th 1.029 4.063
5th 1.129 2.955
6th 0.943 2.955
Reverse 4.600 2.955
Focus ST Unique Features
7
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

MANUAL 6-SPEED TRANSMISSION OPERATION
Using the Clutch
Note:During each shift, the clutch pedal must be fully pressed to the
floor and the accelerator fully released. Failure to follow this may cause
increased shift efforts, prematurely wear transmission components, or
cause gear clash or damage to the transmission. Make sure the floor mat
is properly positioned so it doesn’t interfere with the full extension of the
clutch pedal.
Note:If you attempt to shift when the drive wheels are spinning with a
loss of traction, it is possible to cause damage to the transmission. Do
not attempt to shift when the drive wheels do not have traction.
Note:Do not drive with your foot resting on the clutch pedal or use the
clutch pedal to hold your vehicle at a standstill while waiting on a hill.
These actions will reduce the life of the clutch.
Your vehicle is equipped with a twin disc clutch. Due to the high
performance of the powertrain, a certain amount of noise from the
transmission is normal.
The manual transmission has a starter interlock that prevents cranking
the engine unless the clutch pedal is fully pressed.
To start the vehicle:
1. Make sure the parking brake is fully set.
2. Press the clutch pedal to the floor, then put the transmission selector
lever in positionN.
3. Start the engine, then press the brake pedal and release the parking
brake.
Driving Your Focus ST
10
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

4. Move the transmission selector lever to position1, then slowly release
the clutch pedal while slowly pressing on the accelerator.
5. To engage reverse, lift up on the reverse lockout ring located under
the shift knob and move the transmission selector lever fully to the left
and forward.
Recommended Shift Speeds for Maximum Fuel Economy
When accelerating, upshift according to the following chart:
Upshifts when accelerating*
Shift from:
1 - 2 12 mph (19 km/h)
2 - 3 23 mph (37 km/h)
3 - 4 32 mph (51 km/h)
4 - 5 41 mph (66 km/h)
5 - 6 42 mph (67 km/h)
*pending EPA fuel economy certification
Operating at High Speeds
Your ST vehicle is capable of high speeds and is equipped with tires
rated for the vehicle’s maximum speed. Remember to drive safely, obey
all traffic laws and only operate your ST vehicle at high speeds at
locations equipped and designed to do so safely. Before operating your
vehicle at high speeds:
•Verify correct tire pressures (seeTiresin this supplement).
•Inspect wheels and tires for wear and damage. Replace any damaged
wheels or tires.
•Do not operate your vehicle at high speeds with more than two
passengers or while carrying cargo.
Driving Your Focus ST
11
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

ENGINE SPECIFICATIONS
Engine 2.0L EcoBoost engine
Cubic inches 122
Required fuel Minimum 87 octane
Firing order 1–3–4–2
Ignition system Coil on plug
Compression ratio 9.3:1
Spark plug gap 0.027-0.031 in. (0.70-0.80 mm)
Drivebelt Routing
2.0L EcoBoost
A. The long drivebelt is on the first pulley groove closest to the engine.
B. The short drivebelt is on the second pulley groove farthest from the
engine.
CHECKING THE ENGINE OIL
Refer to thescheduled maintenance informationfor the appropriate
intervals for checking the engine oil.
1. Make sure the vehicle is on level ground.
2. Turn the engine off and wait 15 minutes for the oil to drain into the
oil pan.
Note:The oil dipstick on the Focus ST is integrated into the oil drain
back system. The oil reading on the dipstick will be influenced by oil
draining back into the sump from the cylinder head if the oil level is
checked without waiting 15 minutes after shutdown.
3. Set the parking brake and make sure the transmission selector lever is
securely latched in first gear.
4. Open the hood. Protect yourself from engine heat.
A
B
Capacities and Specifications
21
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

Item CapacityFord Part Name or
EquivalentFord Part Number / Ford
Specification
Engine coolant
3
5.3 quarts (5.0L)MotorcraftOrange
Antifreeze/Coolant
PredilutedVC-3DIL-B (US)
CVC-3DIL-B (Canada) /
WSS-M97B44-D2
Transmission fluid 1.8 quarts (1.7L)MotorcraftDual Clutch
Transmission FluidXT-11-QDC
WSS-M2C200-D2
1Use only MotorcraftDOT 4 LV High Performance Brake Fluid or equivalent meeting
WSS-M6C65-A2 and ISO 4925 Class 6. Use of any fluid other than the recommended fluid may
cause brake system damage.2Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the
requirements of Ford specification WSS-M2C946-A, SAE 5W-30 and display the API Certification
Mark. Your engine has been designed to be used with Ford engine oil, which gives a fuel
economy benefit while maintaining the durability of your engine. Using oils other than the one
specified can result in longer engine cranking periods, reduced engine performance, reduced fuel
economy and increased emission levels.3Add the coolant type originally equipped in your vehicle.
Capacities and Specifications
26
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)

MOTORCRAFT PART NUMBERS
Component 2.0L GTDI EcoBoost engine
Engine oil filter* FL-910-S
Engine air filter FA-1908
Engine fuel filter Service for life
Spark plug CYFS12Y2 (100,000 mile service)
*Only use the specified replacement engine oil filter. The use of a
non-specified oil filter can result in engine damage.
TRANSMISSION CODE DESIGNATION
Description Code
Getrag-Ford Transmission (GFT)
Six-speed manual transaxle (MMT6)V
Capacities and Specifications
27
2013 Focus ST(stf)
Supplement, 1st Printing
USA(fus)