2013 FORD FOCUS ECO mode

inSTrumenT pAneL
1 Cruise Control*
To set your cruise control speed:
1) Press the ON control and release.
2) Accelerate to the desired speed.
3) Press the SET + control and
release, then take your foot off
the accelerator.
After your speed has been set, you can press
SET +/SET - to adjust your cruise speed. To
disable, tap the brake, press the clutch pedal
or pull the CAN (Cancel) control toward you.
Note: Using the clutch pedal to cancel a set
speed may cause the engine speed to
increase briefly.
2 Information Display
Provides information about various
systems on your vehicle. Use the left-hand,
5-way controls located on the steering
wheel to choose and confirm settings
and messages. Refer to the Information
Displays chapter of your Owner’s Manual
for more information.
3 Service Engine Soon Light
Illuminates briefly when the ignition is
turned on. If it remains on or is blinking after
the engine is started, the on-board diagnostics system (OBD-II) has detected a malfunction.

Drive in a moderate fashion and contact your
authorized dealer as soon as possible.
4 Tilt/Telescope Steering Column*
Unlock the steering wheel by pulling the lever
down. Adjust the wheel to the desired position.
Push the lever back up to lock the steering
wheel in place.
5 Voice Controls*
Pull toward you to access voice recognition.
Press to access phone mode or to answer a call.
Press to exit phone mode or end a call.
Press the arrow controls to cycle through the
menu selections and press OK to confirm
your selection.
6 Push Button Start*
Allows you to start your vehicle by pressing
the ENGINE START/STOP button while fully
pressing down on the brake pedal. Press the
button again to turn the engine off.
Note: Your Intelligent Access key
* must be
inside the for keyless starting to work.
7 Audio Controls*
Use the right-hand, 5-way controls to
adjust your audio system:
(Volume): Press to increase (+)
or decrease (-) volume levels.
(Seek): Press the right arrow to hear the
next saved radio station, CD track or MP3 choice.
Press the left arrow to hear the previous selection.
Press M to select a different audio source.
8 Wiper Controls
Use the rotary control on the stalk to adjust the
wipe intervals. Pull the stalk toward you to spray
and wash the windshield. Press the button at the
end of the lever to turn the rear wiper* on, off or
change to intermittent wipe.
9 Hazard Control
10 Power Door Locks
Press the control to lock or unlock
the doors. When the light on the
button is on, it indicates that all
doors and the luggage compartment are locked.
When the light is off, it indicates that one or more
of the doors are unlocked.
2013 focus
45
15
27
4
38
*if equipped
910
2
6

SYnc®2013 focus
Commonly used voice commands –
SYNC… say the word
Every time you want to give SYNC a voice command, you
must first pull the voice control and when prompted,
speak your voice command. For a list of voice commands
say “What can I say?”
Using My Phone with SYNC:
Note: You must download your phone book to make phone
calls with voice commands by name. Contacts listed in all caps
will require you to spell them (i.e. JAKE, will be J-A-K-E).
Making a phone call: Use SYNC to make a phone call to
anyone in your phone book by pulling the voice control
and when prompted, giving any of the following
voice commands:
Call Call at work
Call on cell Call at home
For example, you could say “Call Jake Smith at home”. SYNC
repeats the command back to you and dials the number.
Note:
• You can also make phone calls by pulling
and when
prompted, giving the voice command “Dial”, then verbally
saying the phone number.
Answering incoming calls: Whenever you have an incoming
call, you will be able to see the name and number of the
person calling in your display. Press the phone button
to
answer an incoming call. You can hang up at any time by
pressing and holding the phone button
. Do not disturb mode: This feature blocks incoming calls
and text messages, and saves them for later. You still have
access to outgoing calls when this feature is active. Say the
voice command, “Do not disturb on” to enable and “Do not
disturb off” to disable.
Using SYNC to access digital media
SYNC has a media hub with multiple inputs allowing you
to access personal media from your digital devices. Plug in
your USB media devices such as phones and MP3 players
and use SYNC to play all of your favorite music. Note: SYNC
indexes your music. The more music that is stored on your
device, the longer it takes SYNC to index.
Using voice commands to play music: You can use voice
commands to access and play music on your digital media
player when it is plugged into your media hub
1)
Plug your media player into your USB port.
2) Pull the voice control
. When prompted say
“USB”, then follow-up saying one of the following
voice commands.
“Play all” “Play next song”
“Play song ” “Play album ”
3) You will hear the command repeated back to you and the
selected item will play.
Do more
After creating your account at SyncMyRide.com (U.S.) or
SyncMyRide.ca (Canada), use SYNC® services to get the
most out of your SYNC experience. This includes voice-
activated, turn-by-turn directions, the latest traffic reports,
business searches, sports scores, stock market reports and
more. Say the voice command, “Services”, and SYNC will
guide you through the rest.
67*if equipped*if equipped
Getting started with
your SYNC system
SYNC is a hands-free, voice recognition
system used for entertainment,
information and communication.
SYNC…Say the word.
Before you get started:
1) Set up your owner account at
SyncMyRide.com (U.S.) or
SyncMyRide.ca (Canada).
Register by following the on-screen
instructions. After registering, you
can see what available services
you are eligible for.
2) SYNC uses a wireless connection
called Bluetooth
® to communicate
with your phone. Turn Bluetooth
mode on in your phone’s menu
options. This lets your phone find
SYNC. If you need more details on
setting up your phone with SYNC,
visit SyncMyRide.com (U.S.) or
SyncMyRide.ca (Canada), or your
phone manufacturer’s website.
Pairing your phone with SYNC:
In order to use many of the features of
SYNC, you must first pair and connect
your phone with SYNC.
To pair your phone for the first time:
1) Make sure that your vehicle is in
(P) park and both your ignition and
radio are turned on.
2) Press the phone button and when
the display indicates No Phone
Found press OK.
3) Take out your phone and turn on
Bluetooth. When Add Bluetooth
Device? appears in the SYNC
display press OK.
4) Select SYNC in the list of Bluetooth
devices on your phone and enter
the code shown on the display.
This code connects your phone to
your car.
5) The display will indicate when the
pairing is successful. Note:
The system may prompt you to:
• Set your phone as primary/favorite
(the primary phone will receive
messages and voice mails).
• Download your phone book
(this is required to use the full
set of voice commands).
• Turn on 911 Assist
®.
Tips:
• Make sure you accept SYNC’s
request to access your phone.
• To pair subsequent phones, please
refer to Pairing Subsequent Phones
in the SYNC chapter of your
Owner’s Manual.
• If you are experiencing pairing
problems, try performing a clean
pairing by deleting your device
from SYNC and deleting the SYNC
connection from your phone, and
then repeat the process.