2013 FIAT PANDA technical specifications

This function is timed and switches off automatically
after 4 minutes for the windscreen and 20 minutes
for the rear window and door mirrors.
Press the
button again to switch the function off
in advance.
To activate the heated windscreen again press the
button
:
❒twice with LED on the button still on;
❒once with LED on the button off.
When the button
is pressed, the heated
windscreen activates if it has not been activated
already by button.
IMPORTANT Do not apply stickers on the inside of
the rear window over the heating filaments to avoid
damage.
IMPORTANT To draw in air from the outside, press
the
button. The LED next to the button
switches off.
INTERNAL AIR RECIRCULATION
ACTIVATION
Air recirculation is carried out according to two
possible operating modes:
❒forced deactivation (air recirculation always
deactivated, air taken from the outside);
❒forced activation (internal air circulation always
activated).
To activate internal air recirculation, press button D
.❒LED on button on: internal air recirculation on;
❒LED on button off: internal air recirculation off, air
drawn in from outside.
When the
button is pressed, the climate control
system automatically activates internal air
recirculation. External air recirculation can always be
activated by pressing the
button (LED off )
and vice versa.
Automatic recirculation operation is activated by
pressing the AUTO button.
IMPORTANT Internal air recirculation makes it
possible to reach the required heating or cooling
conditions more quickly depending on the mode
selected. It is not advisable to switch the air
recirculation on when it is rainy/cold to prevent the
windows from misting up, especially if the climate
control is not turned on. It is advisable to switch the
internal air recirculation on whilst queuing or in
tunnels, or whilst driving on dusty roads, to prevent
the introduction of polluted air. Do not use the
function for a long time, particularly if there are
several passengers on board, to prevent the windows
from misting up.
42GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

CLIMATE CONTROL COMPRESSOR
ACTIVATION/DEACTIVATION
Press the
button to switch on the climate control
compressor.
Compressor on:LED on
button on.
Compressor off:
❒LED on
button switches off;
❒internal air recirculation excluded;
With the climate control compressor switched off,
air cannot be introduced into the passenger
compartment that has a lower temperature than the
outside air; in this case the LED on the
button
will light up.
The deactivation of the climate control compressor
is memorised even after the engine has stopped.
To reactivate the climate control compressor, press
the
or AUTO button again: if you press AUTO,
the other manual settings will be cancelled.
AIR DISTRIBUTION SELECTION
Press one or more of buttons A fig. 30 to manually
select one of the possible air distribution settings for
the passenger compartment:
Air flow to the windscreen and front side
window diffusers to demist/defrost them.Air flow to the footwell diffusers. This air
distribution allows the passenger compartment
to be warmed up quickly.Air flow distribution to centre/side dashboard
diffusers (passenger's body).
+
Air flow distributed between footwell
diffusers and windscreen and front side
window defrosting/demisting diffusers. This
distribution setting allows the passenger
compartment to be warmed effectively and
prevents the windows from misting.
+
Air flow distribution between footwell
diffusers (hotter air) and centre/side
dashboard diffusers (cooler air).
IMPORTANT For the climate control system to
function, at least one of the buttons A must be
operated fig. 30. The system does not allow the
deactivation of all the buttons A.
IMPORTANT Push the
button to turn the climate
control system back on: in this way, all operating
conditions memorised before switching off are
restored.
To restore automatic control of the air distribution
after a manual selection, press the AUTO button.
SWITCHING OFF THE CLIMATE CONTROL
SYSTEM
Press the
button.
The LEDS next to the
symbol and internal air
recirculation indication on the control panel switch
off.
SYSTEM MAINTENANCE
In winter, the climate control system must be turned
on at least once a month for about 10 minutes.
43GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Have the system inspected at a Fiat Dealership
before the summer.
The system uses R134a coolant which
does not pollute the environment in the
event of accidental leakage. Never use
R12 fluid, which is not compatible with the
system components.
ADDITIONAL HEATER
(for versions/markets, where provided)
This allows the passenger compartment to be heated
more quickly in cold weather conditions. The heater
switches on automatically according to the
environmental conditions and with engine started
when the temperature of the engine coolant is low.
The additional heater turns off automatically after
the required comfort conditions are achieved.
The heater only operates if the outside temperature
and engine coolant temperature are low. The heater
will not activate if the battery voltage is too low.
Interaction of Automatic Climate Control
with START&STOP
(for versions/markets, where provided)
Automatic Climate Control
The automatic climate control manages the
Start&Stop function (engine off when the car speed
is zero) to guarantee adequate comfort inside the
passenger compartment.In particular, when the weather is extremely hot or
cold, the Start&Stop function is deactivated until
adequate passenger compartment comfort is
ensured. During these transitory stages the engine is
not stopped, even if the car speed is zero.
When the Start&Stop function is active (engine off at
zero car speed), the climate control system will
request the reactivation of the engine if the inside
temperature conditions rapidly deteriorate (or if the
user requests maximum cooling – LO – or quick
demisting – MAX DEF).
With Start&Stop function active (engine off at zero
car speed), the air flow rate (if managed
automatically) is reduced in order to maintain the
passenger compartment comfort conditions for
as long as possible.
The climate control system control unit manages the
decreased comfort caused by stopping the engine,
and consequently the compressor, as far as possible.
The operation of the climate control system can in
any case be favoured by deactivating the Start&Stop
function using the dedicated button on the
dashboard.
NOTE In particularly severe climate conditions it is
recommended to limit the use of the Start&Stop
function to prevent the compressor from
continuously switching on and off, with consequent
rapid misting of the windows and accumulation of
humidity with unpleasant smells in the passenger
compartment.
44GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

EXTERIOR LIGHTSThe left stalk operates most of the exterior lights.
The ignition key has to be in the MAR position
for the exterior lights to come on.
The instrument panel and the various dashboard
controls will come on with the exterior lights.
SIDE LIGHTS/DAYTIME RUNNING LIGHTS
(DRL)
"Daytime Running Lights"
(for versions/markets, where provided)
With the ignition key turned to MAR and ring nut A
fig. 31 turned to positionOthe daytime running
lights are automatically activated; the other lights and
interior lighting remain off.
WARNING
The daytime running lights are an
alternative to the dipped beam
headlights for driving during the daytime in
countries where it is compulsory to have lights
on during the day, and they are also permitted
in those countries where this not obligator y.
WARNING
Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels.The use of daytime
running lights is governed by the highway code
of the country in which you are driving. Comply
with legal requirements.
SIDE LIGHTS AND DIPPED BEAM
HEADLIGHTS
With the ignition key turned to MAR, turn the ring
nut A fig. 31 to
. If dipped beams are activated,
the daytime running lights go out and the side lights
and dipped headlights come on. The
warning
light will come on in the instrument panel.
When the ignition key is turned to STOP or
removed and the ring nut is turned from O to
, all
the side lights and number plate lights switch on.
The
warning light will come on in the
instrument panel.
fig. 31
F0W0127
45GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

PARKING LIGHTS
These lights can only be turned on with ignition key
in STOP position or removed, by moving the ring nut
A first to positionOand then to position
.
The warning light
switches on on the instrument
panel.
MAIN BEAM HEADLIGHTS
To activate the main beam headlights, with ring nut at
, pull the stalk towards the steering wheel. The
warning light
switches on in the instrument panel.
When the stalk is pulled towards the steering wheel
again, the lights deactivate, the dipped headlights
reactivate and the
warning light switches off.
FLASHING
You can flash the headlights by pulling the stalk
towards the wheel (unstable position). The
warning light will come on in the instrument
panel.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
upwards:right direction indicator activation;
downwards:left direction indicator activation.
Warning light
or
will flash in the instrument
panel. The indicators switch off automatically when
the steering wheel is straightened.Lane change function
If you wish to signal a lane change, place the left stalk
in the unstable position for less than half a second.
The direction indicator on the side selected will flash
five times and then switch off automatically.
“FOLLOW ME HOME” DEVICE
This allows the space in front of the car to be lit up
for a certain period of time.
Activation:with the ignition key on STOP or
removed, pull the stalk towards the steering wheel
within 2 minutes from when the engine is turned off.
At each single movement of the stalk, the lights
will remain on for an extra 30 seconds up to a
maximum of 210 seconds; then the lights are
switched off automatically.
Each time the stalk is operated, the
warning light
on the instrument panel switches on and the display
also shows a message and how long the function
will remain active.
The
warning light switches on when the stalk is
first moved and stays on until the function is
automatically deactivated. Each time the stalk is
activated it increases the time that the lights remain
on.
Deactivation:keep the stalk pulled towards the
steering wheel for more than two seconds.
46GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

WINDOW CLEANINGThe right stalk controls windscreen wiper/washer
and rear window wiper/washer operation.
WINDSCREEN WASHER/WIPER
It can be operated only with the ignition key turned
to MAR-ON.
The ring nut A fig. 32 can be moved to four different
positions:
windscreen wiper off.intermittent operation.continuous slow operation.continuous fast operation.
Move the stalk upwards (unstable position) to limit
operation to the time for which the stalk is held
in this position.When released, the stalk will return to its default
position and the wiper will be automatically stopped.
With the ring nut A fig. 32 in position
, the
windscreen wiper will automatically adapt operating
speed to the speed of the car.
With the windscreen wiper operational, if reverse
gear is engaged, the rear window wiper is
automatically activated.
Never use the windscreen wiper to remove
layers of snow or ice from the windscreen.
In such conditions, the windscreen wiper
may be subjected to excessive stress and the
overload cut-out , which prevents operation for a
few seconds, may intervene. If operation is not
restored (even after turning the key and
restarting the car engine), contact a Fiat
Dealership.Do not operate the windscreen wiper with
the blades lifted from the windscreen.
"Smart washing" function
Pull the stalk towards the steering wheel (unstable
position) to activate the windscreen washer.
Keeping the stalk pulled for more than half a second,
with just one movement it is possible to operate
the washer jet and the wiper at the same time.
The wiper stops working three strokes after the
stalk is released.
fig. 32
F0W0126
47GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

A further stroke after approximately six seconds
completes the wiping cycle.
REAR WINDOW WASHER/ WIPER
It can be operated only with the ignition key turned
to MAR-ON.
Activation
Turn ring nut B fig. 32 from positionOto position
to operate the rear window wiper as follows:
❒in intermittent mode when the windscreen wiper
is not operating;
❒in synchronous mode (at half the speed of the
windscreen wiper) when the windscreen wiper
is operating;
❒in continuous mode with reverse gear engaged and
the control active.
With the windscreen wiper on and reverse gear
engaged, rear window wiping will be continuous.
Pushing the stalk towards the dashboard (unstable
position) the rear window washer jet will activate.
Keep the stalk pushed for more than half a second to
activate the rear window wiper as well. Releasing
the stalk will activate the smart washing function, as
described for the windscreen wiper.
The function stops when the stalk is released.
Do not use the rear window wiper to
removelayersofsnoworice.Inthese
conditions, the windscreen wiper may be
submitted to excessive effor t resulting in the
motor protection cutting in and wiper operation
being inhibited for a few seconds. If operation
is not restored, contact a Fiat Dealership.
48GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

ROOF LIGHTSFRONT ROOF LIGHT
Single-bulb roof light
The lens of roof light A fig. 33 has three positions:
❒right side pressed: light always on
❒left side pressed: light always off
❒central position (neutral): the light switches on and
off when the doors are opened or closed.
Multi-bulb roof light(for versions/markets, where
provided)
The switch A fig. 34 switches on/off the roof light
bulbs.A switch positions:
❒central position (position 1): lights C and D switch
on/off when the doors are opened/closed;
❒pressed to the left (position 0): lights C and D are
always switched off;
❒pressed to the right (position 2): lights C and D
are always switched on.
The lights switch on/off gradually.
B switch positionsfig. 34:
❒central position (position 1): lights C and D are
always switched off;
❒pressed to the left (position 0): light C switches
on;
❒pressed to the right (position 2): light D switches
on.
fig. 33
F0W0237
fig. 34
F0W0051
49GETTING TO
KNOW YOUR CARSAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX