2013 DODGE DART fuse

Cavity Maxi Fuse Mini Fuse DescriptionF02 60 Amp Blue — Direct Battery
Feed #2 To BCM
F03 30 Amp Green — Output For Starter
Relay #1
F04 40 Amp Orange — ESP Pump Motor
F05 40 Amp Orange — DDCT Feed #1
(SDU)
F06 30 Amp Green — Direct Battery
Feed #3 To BCM
F07 40 Amp Orange — EBL RLY Coil,
Blower Motor RLY
Coil
F09 — 5 Amp Tan Radiator Fan En- able RLY, Radiator
Fan Enable RLY
CoilCavity Maxi Fuse Mini Fuse Description
F10 — 10 Amp RedORC
F11 — 20 Amp YellowECM, EPS, Backup
Lamp Switch
F14 — 15 Amp BlueDDCT Feed #2
F15 — 15 Amp BlueDDCT Feed #3
F16 — 15 Amp BlueIgnition Coils, Coil
Capacitor
F17 — 15 Amp BlueESC, Brake Pedal
Switch, OCM
F18 — 20 Amp YellowECM
F19 — 10 Amp RedA/C Compressor
Clutch
554 MAINTAINING YOUR VEHICLE

Cavity Maxi Fuse Mini Fuse DescriptionF20 — 30 Amp GreenEBL
F21 — 20 Amp YellowFuel Pump
F22 — 10 Amp RedORC
F23 — 25 Amp NaturalESC
F24 — 20 Amp YellowECM, Fuel Injec-
tors, Active Grill
Shutter (AGS)
F30 — 20 Amp YellowPower Outlet
(Console)
F81 60 Amp Blue — Interior PDC Bat-
tery Feed, Power
Seats
F82 30 Amp Green — AmplifierCavity Maxi Fuse Mini Fuse Description
F83 40 Amp Orange — HVAC Blower Mo-
tor
F84 — 20 Amp YellowCigar Lighter
F85 — 10 Amp RedSunroof, LRSM,
Power Outlet
(Console), UCI/
AUX Port, Cigar
Lighter
F86 — 20 Amp Yellow—
F87 — 10 Amp RedWastegate, Purge
Solenoid, OBD
Vent Valve, Oxy-
gen Sensor Heat-
ers
F88 — 10 Amp RedHeated Outside
Mirrors
7
MAINTAINING YOUR VEHICLE 555

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENTSpecial design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained personnel.
The following must be observed during installation.
The positive power connection should be made directly to
the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the roof
or the rear area of the vehicle. Care should be used in
mounting antennas with magnet bases. Magnets may affect
the accuracy or operation of the compass on vehicles so
equipped.The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.