2013 Citroen GRAND C4 PICASSO RHD rims

228
Safety
Intelligent traction control
s
ystem ("Snow motion")
When this warning lamp comes on,coupled with the STOPwarning lamp,
accompanied by an audible signal and a
message, it indicates that there is a fault
with the electronic brake force distribution(EBFD), which could cause loss of control of the vehicle when braking.

Operation
When this warning lamp comes on,
accompanied by an audible signaland a message, it indicates that there
is a fault with the ABS, which could cause loss of control of the vehicle
when braking.
Your vehicle has a system to help driving onsnow: intelligent traction control.This system detects situations of difficult surface adhesion that could make it difficult to move off or make progress on deep fresh snow
or compacted snow.
In these situations
, the intelligent traction control limits the amount of wheel slip to provide the best traction and trajectory controlfor your vehicle.
In extremely severe conditions (deep snow,mud, ...), when it proves impossible to move off,
it may be useful to temporarily deactivate theESP/ASR systems to allow the wheels to spin
freely and so allow movement of the vehicle.
The use o
f snow tyres is strongly recommended on sur faces offering low levels of adhesion.

Anti-lock braking system (ABS)
and electronic brake force
distribution
(EBFD)

When changing wheels (tyres and rims),make sure that these are approved for your vehicle.
Normal operation of the ABS may make itself felt by slight vibrations of the brake pedal.
In emergency braking, press very firmly without releasing the pressure.
You must stop as soon as it is safe to do so.
In both cases, contact a CITROËN dealer or a qualified workshop.

229
6
Safety
Dynamic stability control(DSC)


The DSC system offers exceptional safety in normal driving, but this should not encourage the driver to take extra risks or drive at high speed.
The correct operation of the system depends on obser vation of the manufacturer's recommendationsregarding the wheels (tyres and rims),the braking components, the electronic components and the assembly andrepair procedures used by CITROËNdealers.
After an impact, have the systemchecked by a CITROËN dealer or a qualified workshop.



Activation

This system is activated automatically each
time the vehicle is started.
It comes into operation in the event of a grip or
trajectory problem.
Deactivation
In exceptional conditions (starting a vehicle which is bogged down, stuck in snow, on softground...), it may be advisable to deactivate
the DSC system, so that the wheels can move
freely and regain grip.
This is indicated by
flashing of thiswarning lamp in the instrument panel.



Operating fault
But it is recommended that the system bereactivated as soon as possible.
)
Press the button.
This warnin
g lamp and the indicator lamp in the button come on: the
DSC system no longer acts on theoperation of the engine.
Reactivation
The system is reactivated automatically each
time the ignition is switched back on or from 30 mph (50 km/h).
) Press the button again to
reactivate it manuall
y.I
f this warning lamp comes on,accompanied by an audible signaland a message, this indicates a fault
with the system.
Contact a CITRO

270
Practical information
*
Depending on version. The complete tooling
is with the spare wheel.











Changing a wheel Procedure for changing a wheel with a punctured tyre by the spare wheel using the tools provided with the vehicle.
Some of the tools are accessible from inside
th
e boot. The wheel chocks 2as well as thewheelbrace extension 6are stowed under theright hand boot sill.The wheelbrace 1
and the towing eye 7
arestowed under the left hand boot sill.The other tools, the jack 3
and the tool for removing the wheel bolt head finishers for alloy
wheels 4 , are stowed in a box attached to thespare wheel. The assembly is secured under
the vehicle in a carrier. See the "Access to thespare wheel" section).
Access to the vehicle's tools *
2.Wheel chocks for immobilising the vehicle
(except versions with manual gearbox).3.Jack with integral handle.
For raising the vehicle.4. Wheel bolt head cover removal tool.
For removing the wheel bolt head finishers
on alloy wheels.
5. Socket for the security bolts (stowed in the glove box).
For adapting the wheelbrace to the specialsecurity bolts.
6.Wheelbrace extension.
For unscrewing/tightening the spare wheelcarrier drive.
7. To w i ng eye.


Wheel with trim
When removing the wheel
, detach the trimfirst using the wheelbrace 1
pulling at the valvepassage hole.
When refitting the wheel
, refit the trimstarting by placing its notch facing the valve
and press around its edge with the palm of your hand.



List of tools *

All of these tools are specific to your vehicle
and can var
y according to equipment. Do not use them for other purposes. 1.Wheelbrace.
For removing the wheel trim and the wheelfixing bolts.