2013 Citroen GRAND C4 PICASSO RHD ad blue

106
Comfort

















Heating
Temperature adjustment
)
Press one of these buttons,or move the cursor from blue (cold) to red (hot) to adjust the
temperature to your wishes.
Air flow adjustment
) Press one of these buttons toincrease or decrease the speedof the booster fan.


Air distribution adjustment
The intake of exterior air prevents and eliminates misting of the windscreen and side
windows.
The recirculation of interior air prevents exterior
odours and smoke enterin
g the passenger compartment. Win
dscreen.
Footwells.
Centre and side vents. The air distribution can be varied b
y using more
than one button.
Each press of a button activates or deactivates
th
e function.

The indicator lamp is on when the button is activated. For an even distribution of air in the passenger compar tment, the three buttons can
be activated simultaneously.


Air intake / Air recirculation
)
Press this button to recirculate
the interior air. The indicator lamp
in the button comes on.) Press the button again to allow
the intake of exterior air. This is confirmed by the indicator lamp going off.



Avoid driving for too long withoutventilation (risk of misting and deterioration of air quality).
The heatin
g system works only when theengine is running.
Press the button for the " Air conditioning"menu to display the page for the system
controls. The s
ymbol for air flow (a fan) fills progressively
according to the air flow setting made.
By reducing the air flow to the minimum, you
are stopping ventilation of the passenger
compartment.

107
3
Comfort
Dual-zone manual air conditioning with temperature regulation
The air conditioning system operates with the engine running.
The temperature at the nozzles and vents
is re
gulated by the system according to the
temperature in the passenger compartment
and the temperature setting.
Press the button for the " Air conditioning"menu to display the system controls page.
Temperature adjustment
)
Press one of these buttons toreduce (blue) or increase (red)the value.


Air flow adjustment
Press one of these buttons to
increase or decrease the speed of
the air booster fan. The driver and
front passenger can each adjust
the temperature.
The value indicated corresponds to a level of comfor t and not to a temperature in degrees Celsius
or Fahrenheit (depending on the unit selected). A setting of around 21 provides optimumcomfort. Depending on your requirements, a
setting between 18 and 24 is normal.
In addition, it is recommended that a di
fference
between left and right of more than 3 should beavoided. The air
flow symbol (a fan) fills progressivelyaccording to the quantity of air wanted.
By reducing the air flow to minimum, you arestopping ventilation.


Avoid driving too long without ventilation(risk of misting and deterioration of air quality).

127
3
Comfort





Rear multimedia

This multimedia system allows rear passengers
to connect one or two external portablesystems (audio or video player, games consoles, DVD player...). The sound is played
through two Bluetooth ®wireless headphone sets, while the video content is displayed in two
7- i nch screens built into the backs of the frontseat head restraints.
Description

This system operates only with theengine running.
The
pack includes:
- the connection and control panel fitted on
the rear face of the centre console,
- tw
o 7- i nch screens built into the front head restraints (with protective covers),
- two wireless Bluetooth technologyheadphone sets with rechargeable batteries,
- a 12 V charger with two outlets allowing the simultaneous charging of two headphones,
1
. Power switch2.AV1 video input (yellow RCA socket)3.Stereo audio input A (red and white RCA sockets)4.AV2 video input (yellow RCA socket)
5.Stereo audio input B (red and white RCA sockets)6. Selection of display in the left hand screen (AV1 or AV2)
7.Selection of display in the right handscreen (AV1 or AV2) 8. Connection indicator lamps for the Bluetooth audio headphones (blue)

128
Comfort
1. Screen power switch 2.
Display adjustment buttons


Each head
phone set has a switch,
a connection indicator lamp (blue)and a channel selector (A or B).
) With the engine running, connect your
portable system to the RCA connectors (e.g. with AV1 on the left). ) Press the switch on the control panel,
the indicator lamp comes on and the AV1
indicator lamps come on.
) Make a long press on the switch, its
indicator lamp flashes in blue.) Make a long press on the control panelswitch, the pairing with the headphone set
is complete when the blue indicator lampson the headphones and on the system areon continuously. ) Repeat the operation for the other
headphone set.
) Press the screen switch if you have a video source. )
Start playing your por table system.


Operation


The Multimedia system allows theconnection of a third Bluetoothheadphone set, not supplied.


If your seat is in the table position,position a cover to avoid damaging thescreen.
These covers also conceal eachscreen.

)It is possible at any time to modify thesource for the video display (using button 6or 7
on the control panel: the indicator lamp for the source selected comes on) as well as the audio channel (using the selector on
the headphones).

191
4
Driving





Reversing camera


Clean the reversing camera regularly using a soft, dry cloth.
The reversing camera is activated automatically
when reverse gear is engaged.
Depending on version, the image is displayed in
the touch screen tablet or the instrument panel.
The space between the blue lines represents
the width of your vehicle except for the door
mirrors.
The blue lines represent the general direction of the vehicle.
The red lines represent a distance of about
30 cm beyond the edge of your vehicle's
rear bumper. The audible signal becomes continuous from this limit.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.

The turquoise blue curves represent the
maximum turning circle.
The reversing camera cannot in any circumstances be a substitute for thevigilance and responsibility of the driver.

Opening the tailgate causes the display to disappear.


The reversing camera function may be completed with parking sensors.
High pressure jet washingWhen washing your vehicle, do not direct the lance within 30 cm of thecamera lens.

192
Driving





360 Vision
This system provides a view in the instrument panel of the near surroundings of your vehicle,
using cameras mounted at the front and rear of
your vehicle and under the door mirrors.
Dependin
g on the angle of view chosen (front
view, rear view or 360° panoramic view),360 Vision provides special visual assistance
in particular driving conditions such as when entering a blind crossing or monoeuvring in
areas of reduced visibility.Once activated, this function operates up to9 mph (15 km/h). Above 18 mph (30 km/h), thefunction is deactivated automatically.
This system is a visual aid which in nocircumstances can replace the vigilance and responsibility of the driver. The images provided by the cameras may be deformed by the relief. Thepresence of areas in shade, in sunny conditions, or of low ambient light maydarken the image and reduce contrast.
Forward vision

The camera located in the front bumper isactivated and views of the areas located at frontleft and front right appear simultaneously in the
instrument panel.

Rear vision

The camera located in the tailgate is activated
and the view of the area behind your vehicle is
displayed in the instrument panel and behaveslike a reversing camera, whatever the position
of the gear selector lever.
The blue lines represent the width of your
vehicle (excluding mirrors): they move
according to the position of the steering wheel.
The red line represents a distance of 30 cm
from the rear bumper, and the two
green
lines, 1 m and 2 m from the rear bumper,
respectively.

Rear vision is displayed automaticallywhen engaging reverse, regardless of the state of the system.

209
5
Visibility

The system may suffer interference or not work correctly:


- under conditions of poor visibility(for example, snowfall, heavy rainor thick fog, ...),

- if the windscreen is dir ty, misted or obscured (by a sticker, ...) in front of the camera,

- if the vehicle is facing highly reflective signs.


The system is not able to detect:


- road users that do not have their own lighting, such as pedestrians,

- road users whose lighting is
obscured, such as vehicles running behind a safety barrier (on amotorway, for example),

- road users at the top or bottom of a steep slope, on twisty roads, oncrossroads.Switching off
)
In the "Driving assistance"menu, press the button, its
indicator lamp goes o
ff and
the the system changes to
"automatic illumination of headlamps" mode. To reactivate the s
ystem, flash the headlampsagain.
Depending on thesituation, one of these two indicator lamps comes on.

Switching on
)
Put the lighting control stalk ring
in the "AUTO" position.
)
In the " Driving assistance"
menu, press the button, its
indicator lamp comes on.

Operation



- dipped beam is maintained, this
indicator lamp comes on in the
instrument panel.
)Flash the headlamps(going beyond the point
of resistance) to activate
the function.

Once the function is activated, the system
operates as follows:
If the ambient li
ght level is very low and the
traffic conditions permit:


- m
ain beam comes on
automatically: this indicator lamp
comes on in the instrument panel. If the ambient li
ght level is sufficient and/or
if the traffic conditions do not allow illumination
of the main beam headlamps:
Pause
If the situation requires a change of headlampbeam, driver can take over at any time.
) Flashing the headlamps
again pauses the
function and thesystem changes to "automatic illumination of headlamps" mode:


- i
f the AUTO indicator lamp was on in green, the system changes to main
beam,

- i
f the AUTO indicator lamp was on in
blue, the system changes to dippedbeam.

298
Practical information

Exiting economy mode

These functions are reactivated automaticallynext time the vehicle is driven.) In order to restore the use of these
functions immediately, star t the engine and let it run:
-
for less than ten minutes, to use the
equipment for approximately five minutes,
- for more than ten minutes, to use the
equipment for up to approximatel
ythirty minutes.
Let the engine run for the duration specified toensure that the battery charge is sufficient.
Do not repeatedly and continuously restar t theengine in order to charge the battery.
A flat battery prevents the engine from star ting (refer to the "Battery" section).








Load reduction mode
System which manages the use of cer tain
functions according to the level of chargeremaining in the battery.
When the vehicle is bein
g driven, the loadreduction function temporarily deactivates certain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated automatically as soon as conditions permit.








Energy economy mode


Switching to economy mode
A message then appears in the instrument
panel screen indicating that the vehicle has
switched to economy mode and the activefunctions are put on standby.
If a telephone call is being made at this time, it
will be maintained for around 10 minutes with
the Bluetooth hands-free s
ystem of your audio
s
ystem.
S
ystem which manages the duration of use of certain functions to conserve a sufficient level
of charge in the battery.
After the en
gine has stopped, you canstill use functions such as the audio and
telematics system, windscreen wipers, dippedbeam headlamps, cour tesy lamps, etc. for a maximum combined duration of about forty minutes.