2013 Citroen DS5 wheel

Practical information

Access to the spare wheel

The spare wheel is suppor ted by a cable-driven carrier underneath the vehicle.
Ta k i ng out the wheel
)
Raise the floor to reveal the spare wheelcarrier drive nut.)
Turn this drive nut fully clockwise, using
the wheelbrace 1and the extension 8, tounwind the carrier cable.
) Detach the wheel from the rear of the
vehicle. ) Remove the hook with its connection plate
to release the wheel, as shown in the
ill
ustration. ) Pull out the wheel.

Putting the wheel back in place
)Pass the hook with its connection plate into
the wheel, as illustrated.) Raise the wheel underneath the vehicle byturning the carrier drive nut anticlockwiseusing the wheelbrace 1
and the extension 8
.
)Tighten fully and check that the wheel is horizontally flush against the floor.

195
Practical information
Removing a wheel

Parking the vehicle

Immobilise the vehicle where it does notblock traffic: the ground must be level, stable and not slippery. Apply the parking brake unless it has been programmed to automatic mode, switch off the ignition and engage firstgear *
to block the wheels. Check that the braking warning lamp and the Pwarning lamp in the parkingbrake control lever come on.
The occupants must get out of the vehicle and wait where they are safe.
Never go underneath a vehicle raised using a jack; use an axle stand.
List of operations
)
Depending on equipment, remove the cover from from each of bolts using the tool 3
or removethe hub cap using tool 4
. )
Fit the security socket 5
on the wheelbrace 1
to slacken the security bolt (if fitted).)
Slacken the other bolts (no more than a 1/4 turn) using the wheelbrace 1
only.

*
position R
for the electronic
gearbox system; Pfor the automatic gearbox.

)Place the jack 2 in contact with one of the
two front A or rear Blocations provided on
the underbody, whichever is closest to the
wheel to be chan
ged.
)Raise the vehicle until there is sufficientspace between the wheel and the ground
to admit the spare (not punctured) wheel easily.)Remove the bolts and store them in a clean place. )Remove the wheel.
) Extend the jack 2
until its base plate is incontact with the ground. Ensure that the centreline of the jack base plate is directlybelow the location Aor B
used.

197
Practical information

Fitting a wheel
Fitting the "space-saver"spare wheel
If your vehicle is fitted with alloy wheels, when tightening the bolts on fitting,it is normal to notice that the washersdo not come into contact with the "space-saver" spare wheel. The wheel is secured by the conical surface of each bolt.
After changing a wheel
To c o r r e c t ly store the punctured wheelin the boot ( not in the location of the space-saver wheel ), first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checkedby a CITROËN dealer or a qualified
workshop without delay. Have the punctured wheel repaired and refitted to the vehicle as soon as possible.


List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts fully by hand.)
Pre-tighten the security bolt using the
wheelbrace 1fitted with the security socket 5.) Pre-tighten the other bolts using the
wheelbrace 1only.

)Lower the vehicle fully. )Fold the jack 2 and detach it. )
Tighten the security bolt using the
wheelbrace 1 fitted with the securitysocket 5.)
Tighten the other bolts using the
wheelbrace 1 only.)
Refit the bolt covers on each of the bolts or
the hub cap (depending on equipment). ) Store the tools in the box.

215
Practical information




Towing the vehicle
Procedure for having your vehicle towed or for towing another vehicle using a removable
tow
ing eye.
To w i ng your vehicle
To w i ng another vehicle
Access to the tools
The towing eye is installed in the boot under
the floor.
To gain access to it: )open the boot, )remove the towing eye, located in the tool box.

)
On the front bumper, unclip the cover by
pressing at the bottom to disengage thesecuring lugs.) Screw the towing eye in fully.)
Install the towing bar.)
Switch on the hazard warning lamps on the
t
owed vehicle.
) On the rear bumper, unclip the cover bylevering at the left with the point of the
towing eye. ) Screw the towing eye in fully. )
Install the towing bar. )
Switch on the hazard warning lamps on the
t
owed vehicle.

When towing with all four wheels on theground, always use a towing bar.
When towing with only two wheels on the ground, always use professionallifting equipment.
When towing with the engine off, thereis no longer any braking or steeringassistance.

)Place the gear lever in neutral(position N
on the electronic gearbox system or automaticgearbox).Failure to obser ve this special condition could result in damageto certain braking components and the absence of braking assistancethe next time the engine is started.

219Practical information





Accessories
A wide range of accessories and genuine par ts is available from the CITROËN dealer network.
These accessories and par ts have been tested and approved for reliability and safety.
They are all adapted to your vehicle and benefit from CITROËN's recommendation and warranty.



"Comfort":

door deflectors, side window blinds, rear screen blind, isotherm module, coat hanger fixed to head restraint, mobile reading lamp, mirror for caravan, parking sensors...


"Transport systems":

child seats and booster cushions, boot carpet,
boot liner, boot net, boot spacers, transverse
roof bars, bic
ycle carrier, ski carrier, roof boxes,
towbars, wiring harnesses...
If a towbar and wiring harness are fitted
outside the CITROËN dealer network, theinstallation must be done using the vehicle's electrical pre-equipment and fitted following the manufacturer's recommendations.
"Styling":
gear lever knobs, aluminium foot rest, alloy wheels, chrome mirror shells, chrome door aperture finishers...

*
To avoid an
y risk of jamming the pedals:
- ensure that mats are correctly positionedand secured,
- never fit one mat on top of another.
"Security and safety":
anti-intrusion alarm, anti-tilt unit, stolen
vehicle tracking system, child seats and
booster cushions, breathalyser, first aid kit, fire
extinguisher, warning triangle, high visibility
vest, wheel security bolts, snow chains, non-
slip covers...

"Protection":

mats * , seat covers compatible with lateral
airbags, mud flaps, door protective mouldings,bumper protection strips, vehicle cover...
The rear bodywork has been designedto avoid spray.