Page 154 of 332
Deactivation
Only the passenger's front airbag can be deactivated: )with the ignition off, inser t the key in thefpassenger airbag deactivation switch, )turn it to the "OFF"position, )then, remove the key keeping the switch in
the new position.
This warnin
g lamp comes on in the
instrument panel when the ignition is
on and until the airbag is re-activated.
To assure the safety of your child,the passenger's front airbag mustbe deactivated when you install a "rear facing" child seat on the front passenger seat. Other wise, the child would risk beingseriously injured or killed if the airbag were deployed.
Reactivation
When you remove a child seat that has been
fitted "rear wards facing", turn switch to the
"ON"
position to re-activate the airbag and so
assure the safety of your front passenger in theevent of an impact.
With the i
gnition on, this warning lampcomes on in the instrument panel for approximately one minute, if thepassenger's front airbag is activated.
Operating fault
If this warning lamp flashes, contact
a CITROËN dealer or a qualified
workshop. The passen
ger's front
airbag may no longer be deployed in the event
of a serious impact.
If at least one of the two airbag
warning lamps come on continuously, do not install a child seat on the front passenger seat.
Have it checked by a CITROËN dealer or a qualified workshop.
If this warnin
g lamp comes on in the instrument panel, accompanied byan audible warning and a message in
the multifunction screen, contact a CITROËN
dealer or qualified workshop to have thesystem checked. The airbags may no longer be
deployed in the event of a serious impact.
Page 156 of 332
Curtain airbags
System which protects the driver and passengers (with the exception of the rear centre passenger) in the event of a serious side
impact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compartment area.
Deployment
The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or par t of the side impact zone B, perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or rear occupant of the vehicle and the windows.
Operating fault
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be deployed.
In the event of a rear or front collision, the airbag is not deployed.
If this warning lamp comes on in the instrument panel, accompanied by anaudible signal and a message in the screen,contact a CITROËN dealer or a qualified workshop to
have the system checked. The airbags may no longer be
deployed in the event of a serious impact.
Page 162 of 332
Gear shift indicator *
Operation
The system intervenes only when driving economically.
Depending on the driving situation and your
vehicle's equipment, the s
ystem may advise you to skip one or more gears. You can
follow this instruction without engaging the
intermediate gears.
The gear engagement recommendations mustnot be considered compulsory. In fact, the configuration of the road, the amount of trafficand safety remain determining factors whenchoosing the best gear. Therefore, the driver remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated.
- The s
ystem may suggest that you engage a
higher gear, if appropriate.
The in
formation appears in the instrument panel in the form of an arrow accompanied bythe suggested gear.
In the case of driving which makesparticular demands on the performance of the engine (firm pressure on theaccelerator pedal, for example, whenover taking...), the system will notrecommend a gear change. The system never suggests:
- engaging first gear,
- engaging reverse gear,
- engaging a lower gear.
*
Accordin
g to engine.
Example:
- You are in third
gear.
- You press the accelerator pedal
moderatel
y.
Page 164 of 332
Display in the instrument panel
Gear lever positions
N. Neutral R.Reverse1 2 3 4 5/6. Gears in manual mode.AUTO.
This comes on when automated modeis selected. It goes off when changing to manual mode.
)Place your foot on the brakewhen this warning lamp flashes (e.g.: star ting the engine).
You must keep your foot on the brake pedal while star ting the engine.
Moving off
)
Select position N
. )
Press the brake pedal fully. )
Star t the engine.
N
appears in the instrument panel.
N
flashes in the instrument panel screen if the gear lever is not in position Nwhen starting.
)
Select automated mode (position A
), Amanual mode (position M ) or reverse(position R
) R
AUTOand 1
, 1or R
appear in the
instrument panel.
) Release the parking brake. )
Progressively take your foot off the brakepedal.
Vehic les fitted with the 6 -speedelectronic gearbox system then moveoff on their own (refer to the paragraph "Creep function").
Do not press the brake and clutchpedals simultaneously. This can causerapid clutch wear.
)Accelerate away.
Page 165 of 332
163Driving
Creep function
(6-speed electronic gearbox
system)
This function allows the vehicle to be manoeuvered more easily at low speeds (when parking, in traffic jams...).
With the gear lever in position A
, Mor R, the vehicle moves as soon as you take your foot off the brake pedal
, at low speed and
with the engine at idle.
Automated mode
AUTOand the gear engaged appear
in the instrument panel.
The gearbox then operates in auto-adaptive
mode, without an
y action on the par t of the
driver. It continuously selects the most suitablegear taking account of:
- optimisation of fuel consumption,
- drivin
g style,
- road conditions,
- vehicle load. For optimum acceleration, when overtaking another vehicle for example, press theaccelerator pedal fully down, beyond the pointof resistance.
You can change mode at any time bymoving the gear lever from Ato M
or the other way round.
The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.
Do not leave children unsuper visedinside the vehicle when the engine is running.
)
Select position A.
Never select neutral (position N) whenmoving.
Te m p o r a ry control of gear
changing
You can temporarily take over control of gear changes using the steering mounted "+"and "-"
control paddles: if the engine speed
allows, the gear change is carried out.
This function allows you to anticipate certainsituations such as over taking another vehicleor approaching a bend.
After a few moments without any action on the
paddles, the gearbox resumes control of gear changing automatically.
Page 166 of 332
if the engine speed permits.
It is not necessary to release the accelerator pedal during gear changes. When braking or slowing down, the gearboxchanges down automatically so that the vehiclepicks up in the right gear.
Under full acceleration, the change up willnot take place unless the driver operates the gear lever or steering mounted control paddle(unless the engine is close to its maximumspeed).
Reverse
To e ngage reverse, the vehicle must be
immobilised with your foot on the brake. ) Select position R.
Stopping the vehicle
Before switching off the engine:
- change to position N
to be in neutral, or
- leave the vehicle in gear; in this case the
vehicle cannot be moved.
Manual mode
)Select position M.
The gears engaged appear in
succession in the instrument panel.
You can change mode at any time bymoving the gear lever from Ato Mor the other way round.
Never select neutral (position N ) when moving.
There is an audible signal onengagement of reverse.
For all parking situations, you mustapply the parking braketo immobilise the vehicle.
When immobilising the vehicle with theengine running, you must put the gear lever into neutral (position N).
Before doing anything under the bonnet, ensure that the gear lever is inneutral (position N ) and that the parkingbrake is applied. At low speed, i
f reverse gear is requested,
the Nwarning lamp flashes and the gearbox goes into neutral automatically.
To e ngage reverse, put the gear lever into
position N , then to position R.
Page 167 of 332
165
Driving
Operating fault
With the ignition on, if this warninglamp comes on and AUTOflashes,
accompanied by an audible signal and a
message in the multifunction screen, this
indicates a gearbox fault. Have it checked by a CITROËN dealer or a qualified workshop.
Reinitialisation
(5-speed electronic
gearbox)
In exceptional circumstances, thegearbox may need an automatic reinitialisation: starting and gear changing are no longer possible.
AUTO
and - -appear in theinstrument panel. AUTO
and - -
appear in the instrument panel.
)Select position N. )Press the brake pedal. )Wait for around 30 seconds until Nor a gear appears in the instrument panel. )Move the gear lever to position A, then toposition N . )With your foot still on the brake pedal, start
the engine.
The gearbox is operational again. Followin
g disconnection of the battery, it is necessary to reinitialise the gearbox. )Switch on the ignition.
Follow the procedure described above.
Page 169 of 332
167
Driving
When you move the lever in the gate to select
a position, the corresponding indicator is
displa
yed in the instrument panel.P. Park
R.Reverse
N. Neutral D.Drive (Automatic driving)
S.Sport programme 7.Snowprogramme1 2 3 4.Gears engaged during manual operation-.
Invalid value during manual operation
Displays in the instrument panel
Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel (e.g.: star tingthe engine).
Moving off
If position Nis engaged inadvertently while driving, allow the engine to return to idle then engage position Dto accelerate.
When the engine is running at idle, withthe brakes released, if position R, D
or Mis selected, the vehicle moveseven without the accelerator being pressed.
When the engine is running, never leave children in the vehicle withoutsupervision.
When carrying out maintenance with the engine running, apply the parkingbrake and select position P.P
)
Apply the parking brake. )
Select position Por N. )
Start the engine.
If this procedure is not followed, an audible
signal is heard, accompanied by a message in
the multifunction screen. ) With the engine running, press the brake
pedal.
) Release the parking brake. )
Select position R , D
or M . )
Gradually release the brake pedal.
The vehicle moves off immediately.
