2013 Citroen C4 PICASSO seats

85
3
Comfort
Passenger's seat backrest angle
)Pull the control upwards to adjust thebackrest.
When the backrest angle is correct, release the control.
Ta b l e position for thepassenger's seat backrest


This position, associated with the position of
the rear seats, allows you to carry long objects
inside the vehicle.
When the backrest is at the correct angle, release the control lever. To ensure that thebackrest does not suddenly fold forwards and hurt you, restrain it with your back or your hand while operating the control.
Check that there is no object that could inter fere with the movement of the seat, both above and below.
)
Place the head restraint in the low position,raise the armrest and fold the fixed table onto the back of the seat.)
Pull the control fully up and tip the backrest
forwards.
To return to the normal position, guide thebackrest backwards until it locks.

86
Comfort











Front seats
Electric adjustments
Forwards-backwards (driver's
seat)
)Push the control forwards or rearwards toslide the seat.

Seat backrest angle
)
Tilt the control forwards or rearwards to
adjust the angle of the seat backrest.



Seat cushion height and angle
)Operate the rear part of the control
upwards or downwards to obtain thedesired height.)Operate the front par t of the control
upwards or downwards to obtain the
desired angle.

To avoid discharging the battery, carry outthese adjustments with the engine running.

90
Comfort
Electric leg rest
Manual passenger seat
)Press the front or rear part of the control tounfold or fold away the leg rest.
The movement stops when you release the
control.







Heated seats control
)Use the adjustment wheel to switch on and select the level of heating required:

0:
Off. 1:Low.2:Medium. 3:
High.
With the en
gine running, the front seats can be heated separately.
Before operating the leg rest, ensurethat nothing could inter fere with itsmovement.


Electric passenger seat
)
Push the control forwards or backwards to unfold or fold away the leg rest.
The movement stops when you release thecontrol.

92
Comfort











Second-row seats


Forwards-backwards adjustment
)Raise the lever A
, located at the front of
the seat cushion, and adjust the seat to the
desired position. The
3 seats in the 2nd row are independent of each other and are all the same width. Their backrests can be folded to vary the load space in the boot.

93
3
Comfort
)Pull the strap B and guide the seatrearwards.
The backrest reclines and the seat base pivots
slightly.


"Comfort" position


Returning the seat to the initialposition
)Pull the strap B
and guide the seatforwards.

Super vise any movements of seats when made by children.
To remove it:
- move the head restraint to the high position,
- press lu
g Apulling the head restraint upwards at the same time. Th
e rear head restraints can be removed and have two positions:
- high, position for use,
- low, storage position. To raise a head restraint, pull it upwards.
To lower it, press lug A
then the head restraint.
Rear head restraints

Never drive with the head restraintsremoved; they must be in place and correctly adjusted.
T
o refit it:
- engage the rods of the head restraint in the
openings keeping then in line with the seat
back.

Comfort head restraints

Depending on version, the sides can be folded
to obtain a more comfortable position.

94
Comfort
Flat floor
Folding a seat
From the outside) Pull firmly upwards on strap C, as indicated
by the arrow, to unlock the seat; keep
pulling until the seat is fully folded.
Push the seat backrest gently forwards so that the backrest folds onto the seat cushion. The assembly lowers onto thefloor. From the boot, when loadin
g for example You can fold the second-row seats from theboot, after first folding the third-row seats. )Pull on the strap Dto release the seat in
question then push forwards lightly on the backrest.
To avoid any damage to the mechanism,
the strap D unclips if too much force isapplied. Simply clip it in place again for thesystem to be operational again.
)Place the seats in the fully back position. Each seat can be
folded onto the floor to vary
the the space available in the boot.

95
3
Comfort

Repositioning a seat


Before operating the rear seats, check that the outer rear seat belts are notloose, to avoid damaging them. The
centre belt must be stowed. Fix the tongues of the three belts to their anchorage points.
Continuity panels
These continuity panels are not designed to support a weight greater than 30 kg.Releasin
g / locking the continuity panels) Before unfolding the continuity panels, check that the seats in the 2 ndrow are fullyback. )
Slide the continuity panel latch upwards to
release. ) Straighten the continuity panel, then slide
the latch downwards to lock it.
)If necessary, straighten the continuity panels for the seats in the 2nd row and lockthem in place.)Raise the backrest and push it rear wards
until it locks in position

Each seat has a continuity panel at the bottom
of the backrest, that once unfolded:
- provides a continuous load surface in the boot, whatever the position of the seats,
- avoids objects sliding under the seats in
the 2nd row.

96
Comfort
Access to the third row
seats
Access to the third-row seats is via the outer second-row seats.
)Pull the lever E
. The seat unlocks andthe seat cushion comes up against thebackrest. )Hold the lever E
in the raised position, pushing for wards. The whole seat slides
towards the front seat. Space becomes free behind the seat, the third-row passengers can get to their seats.





Leaving the vehicle from
the third-row seats
Repositioning a seat, from
the outside, with the door
open

In the event of a failure of this system(lever E ), the passengers in the thirdrow can also leave the vehicle after first folding the backrests of the second-row seats using the strap D. Do not allow children to operate the seats without supervision.
)
Lift the lever E. The seat unlocks andthe seat cushion comes up against the backrest.
)
Push the seat backrest, still holding the lever E
in the raised position.
If there are passen
gers seated in the third row:)manually return the assembly as far as possible rear wards; the seat does not return to the fully back position, soas to retain legroom for the third-row passengers,)fold the seat cushion until it locks.
Ensure that there is no object on or under the seat that you want to move.


Before operating the seats, ensure that the tables on the back of the first-row
seats are folded away.