Page 98 of 288
Fittings
96
Boot fi ttings
Rear parcel shelf(see following page for details)2.Hooks(see following page for details)3.Location for Hi- Fi amplifier4.Stowing rings5.Storage box (version equipped with a
temporary puncture repair kit)
(see following page for details) or
Tool box (version equipped with a spare
wheel) (refer to section "Practical Information -§ Changing a wheel")
Page 99 of 288
6
Fittings
97
Rear parcel shelf
To remove the shelf: )unhook the two cords, )raise the shelf slightly, then unclip it on each side.
Hooks
The hooks can be used to hold shopping bags.
Storage box
)
Raise the boot carpet by pulling the strap
upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warn
ing triangles, ...
) refit the boot floor carpet by folding itslightly in the middle.
Page 149 of 288
11
Practical information
147
Temporary puncture repair kit
Description of the kit
A.
"Sealant" or "Air" position selector.
B. On "I"
/ off "O"
switch. C.
Deflation button. D.
Pressure gauge (in bar or p.s.i.).E.
Compartment housing:
- a cable with adaptor for 12 V socket,
- various inflation adaptors for
accessories, such as balls, bicycle
t
yres...F
.Sealant car tridge. G.White pipe with cap for repair.
H. Black pipe for inflation. I.
Speed limit sticker.
Access to the kit
This kit is installed in the storage box, under the boot floor.
The speed limit sticker I
must be affixedto the vehicle's steering wheel to remind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph(80 km/h) when driving with a tyre repaired using this type of kit.
Complete s
ystem consisting of a compressor
and a sealant car tridge which permits temporary repair of a tyre so that you can rdrive to the nearest garage.
It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.
Page 154 of 288
Practical information
152
Changing a wheel
The tools are installed in the boot under the
floor.
To gain access to them: )open the boot, )raise the floor, )remove the polystyrene storage box, )unclip and remove the box containing the
tools.
Access to the tools
Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
List of tools
All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removal of
the wheel fixing bolts. 2. Jack with integral handle.
For raising of the vehicle. 3. "Bolt cover" tool.
For removing the bolt protectors (covers)on alloy wheels. 4.Socket for the security wheel bolts (located
in the glove box).
For adapting the wheelbrace to the special "security" wheel bolts (if your vehicle has
them).
Page 155 of 288
11
Practical information
153
Wheel with trim
When removing the wheel
, firstdetach the trim using the wheelbrace 1pulling at the valve passage hole. When refitting the wheel
, refit thetrim star ting by placing its cut-out at the valve and press around its edge withthe palm of your hand.
Access to the spare wheel
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be steel or of the "space-saver" type.
To gain access to it, refer to the paragraph
"Access to the tools" on the previous page.
Fitting the steel or "space-saver" type spare wheel
If your vehicle is fitted with alloy wheels, it is normal to notice, when tightening the bolts on fitting, that the washers donot come into contact with the steel or "space-saver" type spare wheel. Thewheel is secured by the conical contactof each bolt.
Page 156 of 288
Practical information
154
Taking out the wheel
)Unscrew the yellow central bolt. )Raise the spare wheel towards you from
the rear. )Take the wheel out of the boot.
Putting the wheel back in place
)
Put the wheel back in its housing. )
Unscrew the yellow central bolt by a few
turns then put it in place in the centre of the
wheel. ) Tighten fully until the central bolt clicks to
retain the wheel correctl
y.
)Put the box back in place in the centre of
the wheel and clip it. )Put the polystyrene storage box back inplace. )Refit the boot floor carpet by lightly
folding it in two (refer to the section
"Fittings - § Storage box").
On vehicles equipped with a "space-saver" type spare wheel, the puncturedwheel cannot be stowed in place of the "space-saver" wheel.
Page 159 of 288
11
Practical information
157
List of operations
)
Put the wheel in place on the hub. )
Screw in the bolts by hand. )
Pre-tighten the security bolt (if your vehiclehas them) using the wheelbrace 1
fitted
with the security bolt socket 4.
)
Pre-tighten the other bolts using the
wheelbrace 1only.
Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typetemporary use spare wheel, do notexceed 50 mph (80 km/h).Have the tightening of the bolts and thepressure of the spare wheel checkedby a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired and replace it on the vehicle as soon aspossible.Do not drive with more than one temporary use spare wheel fitted to the vehicle at one time.
Page 166 of 288
Practical information
164
Rear lamps
1.Brake / sidelamps (P21/5W).2.Direction indicators (PY21W amber)3. Foglamp, right-hand side (PR21W red)Reversing lamp, left-hand side (P21W).
Changing bulbs
These four bulbs are changed from inside the boot: )spread the four tabs and remove the bulbholder,
)turn the bulb a quar ter of a turn and change it.
To r efit, carry out these operations in reverse order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
) open the boot, )
remove the access flap from the
corresponding side trim panel, )
unscrew the butterfly nut securing the lamp unit, )
unclip the lamp unit connector, )
extract the lamp unit carefully pulling in its
middle towards the outside,
Amber or red bulbs, such as thosefor the direction indicators and rear foglamp, must be replaced by bulbs of the same rating and colour. The lamps on the tailgate are dummy units. They are there for aesthetic purposes only.
