2013 Citroen C3 gearbox

Monitoring
28
Foot on thebrake pedalfixed. The brake pedal must be pressed. With an electronic gearbox, press the brake pedal to start the engine (lever in position N ).
With an automatic gearbox, with the engine running,
press the brake pedal before releasing the parking
brake, to unlock the lever and come out of position P.PIf you wish to release the parking brake withoutpressing the brake pedal, this warning lamp will
remain on.
flashing. With an electronic gearbox, if you hold the vehicle on an incline using
the accelerator for too long, the clutch overheats. Use the brake pedal and
/or the parking brake.
Automatic wipingfixed.The wiper control is pushed downwards. Automatic front wiping is activated.
Warning lampis onCauseAction / Observations

9
Driving
115





Parking brake


Applying
)Pull the parking brake lever fully up to
immobilise your vehicle.

Releasing
)Pull the parking brake lever gently, press
the release button then lower the lever fully.
When the vehicle is bein
g driven,if this warning lamp and the STOPwarning lamp come on, accompanied
by an audible signal and a message
on the multifunction screen, this indicates that the parking brake is still
on or has not been properly released.








6-speed manual
gearbox
Engaging 5th or 6thgear
)
Move the lever fully to the right to engage 5th or 6th gear.
)
Raise the ring under the knob and move
the gear lever to the left then forwards.

Engaging reverse gear
Only engage reverse gear when thevehicle is stationary with the engine at idle.

As a safety precaution and to facilitate starting of the engine:


- always select neutral,

- press the clutch pedal.


When parking on a slope, direct your wheels against the pavement, apply the parking brake and engage a gear.

Failure to follow this advice may cause permanent damage to the gearbox (engagement of 3rdor 4 thgear bymistake).

Driving
116








Gear shift indicator


The system adapts its gear change recommendation according to thedriving conditions (slope, load, ...) andthe demands of the driver (power, acceleration, braking, ...). The system never suggests:


- engaging first gear,

- engaging reverse gear,

- engaging a lower gear. S
ystem which reduces fuel consumption by advising the driver to change up.
With an electronic gearbox, the system is only active in Manual mode.
Operation
Depending on the driving situation and your
vehicle's equipment, the system may advise you to skip one (or more) gear(s). You can follow this instruction without engaging the
intermediate gears.
The
gear engagement recommendations mustnot be considered compulsory. In fact, the configuration of the road, the amount of trafficand safety remain determining factors whenchoosing the best gear. Therefore, the driver remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated.
Example:


- You are in third
gear.
The information appears in the instrument panel in the form of an arrow.
On vehicles with manual gearbox, the arrow can be accompanied by the recommendedgear.

- Yo u
press the accelerator pedal.

- The s
ystem may suggest that you engage ahigher gear.

9
Driving
117














Electronic gearbox
R . Reverse )
With your foot on the brake, move the lever for wards to select this position.N
. Neutral.)
With your foot on the brake, select this
position to star t the engine.
A . Automated mode.)
Move the lever backwards to select this
m
ode. M + / -.
Manual mode with sequential gear changing. )
Move the lever backwards, then to the left
to select this mode, then:
- push for wards to change up a gear,
- or push backwards to change down a gear.

Gear lever

+. Paddle to the right of the steering wheel for changing up. )
Press the back of the steering mounted "+"paddle to change up a gear.
-. Paddle to the left of the steering wheel for changing down.) Press the back of the steering mounted "-"paddle to change down a gear.


Steering mounted controls
Five or six-speed electronically controlled gearbox which offers a choice between the comfor t of automated operation or the pleasure
of manual gear changing.
Tw o d r i v i ng modes are offered:-automatedmode for automatic control
of the gears by the gearbox, without anyaction by the driver,

-
manualmode for the sequential changing
of the gears by the driver, using the gear
lever or the steering mounted control paddles,
In automated mode, you can temporarily takecontrol of gear changes at any time, using thesteering mounted control paddles.
The steering mounted paddles do not allow neutral to be selected, reversegear to be engaged or disengaged, or the driving mode to be changed.

Driving
118
Display in the instrument panel
Gear lever positions
N . NeutralR
. Reverse 1 2 3 4 5 / 6.Gears in manual mode.AUTO.
This comes on when automated modeis selected. It goes off when changing to manual mode.
)
Select position N . )
Press the brake pedal fully.
)
Start the engine.
Nappears in the instrument panel.
)
Select automated mode (position A
), Amanual mode (position M ) or reverse(position R
) R
AUTO
and 1, 1
or R
appear in the
instrument panel.
)Place your foot on the brakewhen this warning lamp flashes (e.g.: star ting the engine).




Creep function
(6-speed electronic gearbox
system)
This function allows the vehicle to be manoeuvred more easily at low speeds (whenparking, in traffic jams...).
With the gear lever in position A
, Mor R, the vehicle moves as soon as you take your foot off the brake pedal
, at low speed and
with the engine at idle.
) Release the parking brake.)
Progressively take your foot off the brake
pedal.
)Accelerate away.
Vehicles fitted with the 6 -speed
electronic gearbox system then move off on their own (refer to the paragraph"Creep function").

Do not leave children unsuper visedinside the vehicle when the engine is running.
You must keep your foot on the brake pedal while star ting the engine.
Do not press the brake and clutch
pedals simultaneously. This can causerapid clutch wear.
N
flashes in the instrument panelscreen if the gear lever is not inposition N
when star ting.

The creep function may be temporarilyunavailable if the clutch temperature istoo high or the slope too steep.


Moving off

9
Driving
119

Manual mode
The gears engaged appear in
succession in the instrument
panel.
The
gear change requests are only carried out
if the engine speed permits.
It is not necessary to release the accelerator
pedal during gear changes.
When braking or slowing down, the gearbox changes down automatically so that the vehicle
picks up in the right gear.
Under
full acceleration, the change up will
not take place unless the driver operates the
gear lever or steering mounted control paddle(unless the engine is close to its maximumspeed).
Te m p o r a ry control of gear changing
You can temporarily take over control of gear changes using the steering mounted "+"and "-"control paddles: if the engine speed allows, the gear change is carried out.
This function allows you to anticipate cer tain
situations such as over taking another vehicle or approaching a bend.
After a few moments without any action on thepaddles, the gearbox resumes control of gear changing automatically.


Automated mode
AUTOand the gear engaged appear
in the instrument panel.
The
gearbox then operates in auto-adaptive mode, without any action on the par t of the
driver. It continuously selects the most suitable gear taking account of:


- optimisation of fuel consumption,

- driving style,

- road conditions,

- v
ehicle load.
For optimum acceleration, when over takinganother vehicle for example, press the
accelerator pedal fully down, beyond the point of resistance.
You can change mode at any time bymoving the gear lever from A
to Mor the other way round.

You can change mode at any time by moving the gear lever from A
to Mor the other way round.

Never select neutral (position N ) when moving.
Never select neutral (position N ) whenmoving.
)Select position A.)
Select position M.

Driving
120

In exceptional circumstances, the gearbox may need an automaticreinitialisation: starting and gear changing are no longer possible.
Reverse
To e ngage reverse, the vehicle must be
immobilised with your foot on the brake. )Select position R.

Operating fault

With the ignition on, if this warninglamp comes on and AUTOflashes,
accompanied by an audible signal
and a message in the multifunction
screen, this indicates a gearbox
fault.Have it checked by a CITROËN
dealer or a qualified workshop.
At low speed, if reverse gear is requested,
the N warning lamp flashes and the gearbox
goes into neutral automatically.
To e n
gage reverse, put the gear lever intoposition N
, then to position R
.
Stopping the vehicle
Before switching off the engine:
- change to position N
to be in neutral,or
- leave the vehicle in gear; in this case the
vehicle cannot be moved.

Reinitialisation
(5-speed electronic
gearbox)

Following disconnection of the battery, it is
necessary to reinitialise the gearbox.) Switch on the ignition.
AUTO
and - -
appear in the
instrument panel.
) Select position N
. )
Press the brake pedal.)
Wait for around 30 seconds until N
or agear appears in the instrument panel.)
Move the gear lever to position A , then to
position N.) With your foot still on the brake pedal, start
the engine.
The gearbox is operational again.
AUTOand --appear in the
instrument panel.

Follow the procedure described above.

Before doing anything under thebonnet, ensure that the gear lever is in neutral (position N) and that the parking brake is applied.
There is an audible signal on engagement of reverse.

For all parking situations, you mustapply the parking braketo immobilise the vehicle.
When immobilising the vehicle with the engine running, you must put the gear lever into neutral (position N)
.

9
Driving
121














Automatic gearbox
1.
Gear lever. 2.Button "S"(sport) . 3.Button "7"(snow).


Gear selection gate
P.Park.
- Immobilisation of the vehicle, parking brakeon or off.
- Starting the engine.R.
Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.
N.Neutral.
- Immobilisation of the vehicle, parking brakeon.
- Star ting the engine.D.
Automatic operation.
M + / - . Manual operation with sequentialchanging of the four gears. )
Push for wards to change up through the gears. or )
Pull backwards to change down through
the gears.

Gear lever

When you move the lever in the gate to select
a position, the corresponding indicator isdisplayed in the instrument panel. P. ParkR.ReverseN.
NeutralD.Drive (Automatic driving)
S.Sport programme
7.Snowprogramme
1 2 3 4. Gears engaged during manual
operation
-. Invalid value during manual operation


Displays in the instrument panel

Foot on brake
)Press the brake pedal when this
indicator lamp is displayed in the
instrument panel (e.g.: star ting
the engine). Four-speed automatic
gearbox which offers a choice between the comfor t of fully automatic
operation, enhanced by spor t and snow programmes, or manual gear changing.
There are there
fore four driving modes:-automatic
operation for electronic management of the gears by the gearbox,
-
sport
programme for a more dynamic style
of driving,

- snowprogramme to improve driving when
traction is poor,
-sequentialoperation for manual changing
of the gears by the driver.