2013 Citroen C3 spare wheel

22
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest items in the bottom of the boot, as close as possible to the rear seats.Limit the loads carried in the vehicle and reduce wind resistance (roof bars, roof rack, bicycle carrier, trailer...). Use a roof box in preference.Remove roof bars and roof racks after use.


At the end of winter, remove snow tyres and refit your summer tyres.


Observe the recommendations on maintenance


Check the tyre pressures regularly, when cold, referring to the label in the door aperture, driver's side. Carry out this check in par ticular:



- before a long journey,

- at each change of season,

- after a long period out of use.
Don't forget the spare wheel and the tyres on any trailer or caravan.


Have your vehicle ser viced regularly (engine oil, oil filter, air filter...) andobser ve the schedule of operations recommended by the manufacturer.


When refuelling, do not continue after the third cut-off of the nozzle toavoid any over flow.


At the wheel of your new vehicle, it is only after the first 1 800 miles(3 000 kilometres) that you will see the fuel consumption settle down toa consistent average.

6
Fittings
93








Boot fi ttings
1.Rear parcel shelf (see following page for details)2.Hooks
(see following page for details)3.Location for Hi- Fi amplifier4.Stowing rings5.Storage box (version equipped with a
temporary puncture repair kit)
(see following page for details) or Tool box (version equipped with a spare
wheel) (refer to section "Practical Information -§ Changing a wheel")

11
Practical information
149














Changing a wheel

The tools are installed in the boot under the
floor.
To gain access to them: )open the boot, )raise the floor,)remove the polystyrene storage box,)unclip and remove the box containing the
tools.

Access to the tools

Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
List of tools

All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removal of
the wheel fixing bolts. 2. Jack with integral handle.
For raising of the vehicle.
3. "Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels. 4. Socket for the security wheel bolts (located
in the glove box).
For adapting the wheelbrace to the special "security" wheel bolts (if your vehicle has
them).

Practical information
150

Wheel with trim
When removing the wheel
, firstdetach the trim using the wheelbrace 1pulling at the valve passage hole. When refitting the wheel
, refit the trim star ting by placing its cut-out at the valve and press around its edge withthe palm of your hand.



Access to the spare wheel
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be
steel or of the "space-saver" type.
To gain access to it, refer to the paragraph"Access to the tools" on the previous page.
Fitting the steel or "space-saver" type spare wheel

If your vehicle is fitted with alloy wheels,it is normal to notice, when tightening the bolts on fitting, that the washers donot come into contact with the steel or "space-saver" type spare wheel. Thewheel is secured by the conical contactof each bolt.

11
Practical information
151
Taking out the wheel
)Unscrew the yellow central bolt. )Raise the spare wheel towards you from
the rear.)Take the wheel out of the boot.
Putting the wheel back in place
) Put the wheel back in its housing. )
Unscrew the yellow central bolt by a few
turns then put it in place in the centre of the
wheel.) Tighten fully until the central bolt clicks to
retain the wheel correctly.
)
Put the box back in place in the centre of
the wheel and clip it. ) Put the polystyrene storage box back inplace. )
Refit the boot floor carpet by lightly
folding it in two (refer to the section
"Fittings -

11
Practical information
153
)Place the jack 2 in contact with one of thetwo front Aor rear B
locations provided on
the underbody, whichever is closest to the
wheel to be changed. )Extend the jack 2until its base plate is in contact with the ground. Ensure that thecentreline of the jack base plate is directly below the location A or Bused.
)
Raise the vehicle until there is sufficientspace between the wheel and the ground
to admit the spare (not punctured) wheeleasily. ) Remove the bolts and store them in a clean
place.
) Remove the wheel.

Practical information
154

List of operations
)Put the wheel in place on the hub. )Screw in the bolts by hand.)Pre-tighten the security bolt (if your vehiclehas them) using the wheelbrace 1fitted
with the security bolt socket 4 .
)Pre-tighten the other bolts using the
wheelbrace 1only.

Fitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typetemporary use spare wheel, do not exceed 50 mph (80 km/h).Have the tightening of the bolts and thepressure of the spare wheel checked by a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired andreplace it on the vehicle as soon aspossible. Do not drive with more than one temporary use spare wheel fitted to the vehicle at one time.

Practical information
156





Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when
braking.

The snow chains must be fitted only to the front wheels. They must never be fitted to "space-saver" type sparewheels.
Take account of the legislation in forcein your country on the use of snow chains and the maximum running speed authorised.


Avoid driving on roads that have been cleared of snow, to avoid damaging your vehicle's tyres and the roadsurface. It is recommended that before you leave, you practise fitting the snowchains on a level and dry surface.If your vehicle is fitted with alloy wheels,check that no par t of the chain or itsfixings is in contact with the wheel rim.


Use onl
y the chains designed to be fitted to the
type of wheel fitted to your vehicle:
Original tyre size Maximum link size.
1
85/65 R15 9 mm
195/55 R16
205/45 R17 not chainable
For more information on snow chains
, contact aCITROËN dealer or a qualified workshop.


Advice on installation
)If you have to fit the chains during ajourney, stop the vehicle on a flat surface on the side of the road.)Apply the parking brake and position anywheel chocks to prevent movement of your
vehicle.)Fit the chains following the instructionsprovided by the manufacturer. )Move off gently and drive for a fewmoments, without exceeding 30 mph (50 km/h). )Stop your vehicle and check that the snow chains are correctly tightened.