2013 CHRYSLER 300 SRT power steering

Door Latches
Check for positive closing, latching, and locking.
Fluid Leaks
Check area under vehicle after overnight parking for fuel,
engine coolant, oil, or other fluid leaks. Also, if gasoline
fumes are detected or if fuel, power steering fluid, or
brake fluid leaks are suspected, the cause should be
located and corrected immediately.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99

▫Headlights On With Wipers (Available with
Automatic Headlights Only) .............212
▫ Rain Sensing Wipers ...................212
 TILT/TELESCOPING STEERING COLUMN . . .214
 POWER TILT/TELESCOPING STEERING
COLUMN — IF EQUIPPED ...............215
 HEATED STEERING WHEEL —
IF EQUIPPED ........................ .216
 ADJUSTABLE PEDALS — IF EQUIPPED ......218
 ELECTRONIC SPEED CONTROL —
IF EQUIPPED ........................ .220
▫ To Activate ......................... .221
▫ To Set A Desired Speed .................221
▫ To Deactivate ....................... .222▫
To Resume Speed .....................222
▫ To Vary The Speed Setting ...............222
▫ To Accelerate For Passing ................222
 ADAPTIVE CRUISE CONTROL (ACC) —
IF EQUIPPED ........................ .223
▫ Adaptive Cruise Control (ACC) Operation . . . .225
▫ Activating Adaptive Cruise Control (ACC) . . . .226
▫ To Activate ......................... .227
▫ To Set A Desired ACC Speed .............228
▫ To Cancel .......................... .230
▫ ToTurnOff......................... .230
▫ To Resume Speed .....................231
▫ To Vary The Speed Setting ...............231
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

The memory seat switch is located on the driver ’s door
trim panel. The switch consists of three buttons: The (S)
button, which is used to activate the memory save
function and the (1) and (2) buttons which are used to
recall either of two pre-programmed memory profiles.Programming The Memory Feature
To create a new memory profile, perform the following:
1. Place the ignition into the RUN position.
2. Adjust all memory profile settings to desired prefer-ences (i.e., seat, side mirror, adjustable pedals [if
equipped], power tilt and telescopic steering column
[if equipped], and radio station presets).
3. Press and release the S (Set) button on the memory switch.
4.
Within five seconds, press and release either of the
memory buttons (1) or (2). The Electronic Vehicle Infor-
mation Center (EVIC) will display which memory posi-
tion has been set.
Memory Seat Switch
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:Your RKE transmitters can be unlinked to your
memory settings by following steps 1-4 above and press-
ing the UNLOCK button (instead of LOCK) on the RKE
transmitter in Step 4.
Memory Position Recall
NOTE:The vehicle must be in PARK to recall memory
positions. If a recall is attempted when the vehicle is not in
PARK, a message will display in the EVIC (if equipped).
To recall the memory settings for driver one, press
MEMORY button number (1) on the driver’s door or the
UNLOCK button on the RKE transmitter linked to
memory position 1. To recall the memory setting for driver two, press
MEMORY button number (2) on the driver’s door or the
UNLOCK button on the RKE transmitter linked to
memory position 2.
A recall can be cancelled by pressing any of the
MEMORY buttons (S, 1, or 2) on the driver’s door during
a recall. When a recall is cancelled, the driver seat, side
mirror, adjustable pedals (if equipped), and power tilt
and telescopic steering column (if equipped) stop mov-
ing. A delay of one second will occur before another recall
can be selected.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

POWER TILT/TELESCOPING STEERING
COLUMN — IF EQUIPPED
This feature allows you to tilt the steering column upward or
downward. It also allows you to lengthen or shorten the
steering column. The power tilt/telescoping steering col-
umn switch is located below the multifunction lever on the
steering column.
To tilt the steering column, move the switch up or down
as desired. To lengthen or shorten the steering column,
pull the switch toward you or push the switch away from
you as desired.
NOTE:For vehicles equipped with Driver Memory Seat,
you can use your Remote Keyless Entry (RKE) transmit-
ter or the memory switch on the driver’s door trim panel
to return the tilt/telescopic steering column to pre-
programmed positions. Refer to “Driver Memory Seat”
in this section.
WARNING!
Do not adjust the steering column while driving.
Adjusting the steering column while driving or driv-
ing with the steering column unlocked, could cause
the driver to lose control of the vehicle. Failure to
follow this warning may result in serious injury or
death.
Power Tilt/Telescoping Steering Switch
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215

•Transmission Temperature Warning Telltale
This telltale indicates that the transmission fluid
temperature is running hot. This may occur with
severe usage, such as trailer towing. If this
telltale turns on, safely pull over and stop the
vehicle. Then, shift the transmission into NEUTRAL and
run the engine at idle or faster until the light turns off.
CAUTION!
Continuous driving with the Transmission Temperature
Warning Telltale illuminated will eventually cause se-
vere transmission damage or transmission failure.
WARNING!
If the Transmission Temperature Warning Telltale is
illuminated and you continue operating the vehicle,
in some circumstances you could cause the fluid to
boil over, come in contact with hot engine or exhaust
components and cause a fire.
• Electric Power Steering Malfunction
This telltale is on when the Electric Power
Steering is not operating and needs service.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 319

•Oil Pressure
Shows the actual oil pressure.
• Battery Voltage
Shows the actual battery voltage.
Engine
When selected, this screen displays miles per hour (mph),
horsepower (hp), torque (ft/lb), oil pressure (psi) and
gear selector values.
Handling
When selected, this screen displays peak g-force, steering
and yaw angles.
Options
When selected, this screen allows you to choose a stan-
dard or customize display for your SRT home page.
SETTING THE ANALOG CLOCK
To set the analog clock at the top center of the instrument
panel, press and hold the button until the setting is
correct.
Setting The Analog Clock
348 UNDERSTANDING YOUR INSTRUMENT PANEL

DRIVING ON SLIPPERY SURFACES .........390
▫ Acceleration ........................ .390
▫ Traction ........................... .391
 DRIVING THROUGH WATER .............391
▫ Flowing/Rising Water ..................391
▫ Shallow Standing Water .................392
 POWER STEERING .....................393
▫ Power Steering Fluid Check ..............394
 FUEL SAVER TECHNOLOGY —
IF EQUIPPED ......................... .395
 PARKING BRAKE ..................... .395
 ANTI-LOCK BRAKE SYSTEM .............398
ELECTRONIC BRAKE CONTROL SYSTEM . . . .400
▫ Anti-Lock Brake System (ABS) ............400
▫ Traction Control System (TCS) ............400
▫ Brake Assist System (BAS) ...............401
▫ Electronic Stability Control (ESC) ..........402
▫ Hill Start Assist (HSA) .................405
▫ Ready Alert Braking ...................407
▫ Rain Brake Support ....................408
▫ ESC Activation/Malfunction Indicator
Light And ESC OFF Indicator Light ........408
▫ Synchronizing ESC ....................409
 TIRE SAFETY INFORMATION .............410
▫ Tire Markings ....................... .410
366 STARTING AND OPERATING