Black plate (6,1)Chevrolet Tahoe Police and Special Service Packages - 2013 - CRC - 3/30/12
15-6 Special Equipment Options
The vehicle is equipped with wiring
provisions for a 12-volt battery
power supply. Refer to the following
information when adding electrical
accessories that will use the 12-volt
power supply feeds connected to
the vehicle's electrical system. The
wiring harness is located below the
instrument panel near the center of
the vehicle. The following
information describes the breaker
and relay location and provides a
wiring diagram to aid in connecting
customer equipment.
Electrical Connections
Notice:Before modifying or
adding any wiring, be sure that it
will work properly with your
vehicle's wiring system. Because
there are so many modifications
that can be made for many
different bodies and accessories,
GM cannot take responsibility
for any changes made. Such
changes may not be covered by
your GM Warranty. Have the work
done by an experienced electrical
technician. All wiring must be properly
protected by fuses, etc. and must
be routed properly so that it will
not be cut, pinched or rubbed by
other parts of the vehicle. Do not
route wiring in areas where it will
be very hot. Be sure not to
overload the vehicle's wiring,
connectors and components. All
added wire must be at least the
same size as the wire being
attached to for proper fuse
protection.
Installation Instructions
–12‐Volt
Accessory Power Supply
1. Disconnect the negative (−)
battery cable at the battery. The
negative (−) battery cable must
be disconnected before the
positive wiring lead is connected
to the power accessory.
2. Locate the power supply harnesses, one under the
instrument panel near the center
of the vehicle, and one within the
driver side rear cargo area jack
stowage compartment. 3. Prepare the wires that are to be
used to connect the power
accessory. Do not remove the
unused wires. Tape unused
wires back in their original
position under the instrument
panel.
4. Complete the wiring installation of the customer added
accessory with additional wire
required for the specific
electrical accessory power
connection. The wire gauge,
3.0 mm² (12 gauge), should be
the same as the wiring of the
installed harness.
5. The ignition must be turned to OFF prior to attaching the cables
to the battery, or serious damage
to the Body Control Module
(BCM) may result.
The windshield wiper switch and
the radio must be turned off
before attaching cables to the
battery.
Black plate (9,1)Chevrolet Tahoe Police and Special Service Packages - 2013 - CRC - 3/30/12
Special Equipment Options 15-9
relay, or equivalent. Replace a
50 amp circuit breaker with a GM
Part No. 15319848 circuit breaker,
or equivalent.
Reinstall the storage tray into the
compartment by lifting it into the
instrument panel.
Auxiliary Battery Power
Junction Blocks
Two auxiliary power junction blocks
are located within the driver side
rear cargo area jack stowage
compartment. Each junction block is
powered directly from the battery
through a 50 amp circuit breaker for
connection to customer‐furnished
equipment. The two circuit breakers
are located in the breaker/relay
panel forward of the instrument
panel glove box. A maximum load of
50 amps (600 watts) can be
connected to each junction block.
The wiring diagram for this circuit is
shown as part of the diagram for
“Wiring Provisions–12 Volt Battery
Power”. The two junction blocks are
connected to coiled 1.5 m (5 ft)
branches of the rear body harness
and fastened near the jack.
Mounting of the junction blocks can
be at customer‐selected rear cargo
area locations permitted by the
branch harness length and using
customer‐furnished mounting
hardware.
The junction blocks should not be
attached to the interior trim plastic
components without appropriate
backing hardware to the mounting
bolts.
To connect the customer-furnished
equipment at the junction blocks,
use the following steps:
1. Disconnect the negative (−)
battery cable.
2. Connect the customer-furnished equipment positive leads to the
junction block terminals and
tighten to 15 N·m (11 lb ft).
The ignition must be turned off
and the vehicle vacated prior to
connecting the negative (−)
battery cable to the battery.
3. Reconnect the negative (−) battery cable to the battery.
Torque the bolt to 5 Y
(3.6 lb ft).
4. Set the time on the clock and radio pushbuttons as needed.
See “Introduction” in the
Infotainment section of the
owner manual for more
information.
Black plate (10,1)Chevrolet Tahoe Police and Special Service Packages - 2013 - CRC - 3/30/12
15-10 Special Equipment Options
Equipment Grounding
Studs - Rear
Compartment
Your Tahoe Police or Special
Service Package has grounding
studs located at the lower driver
side and passenger side rear
compartment liftgate opening for
connection to customer electrical
equipment. A 1.52 m (5 ft) blunt cut
length of #8 awg copper wire is
coiled inside the jack storage
compartment to permit grounding of
electrical equipment that may bemounted forward in the rear
compartment and behind the
second row seatback.
Radio Suppression
Grounding Straps
Your Tahoe Police Package and
Special Service Package are
equipped with additional grounding
straps in the following locations:
.Driver side front frame body
mount bracket to underbody
.Driver side rear frame body
mount bracket to rear underbody
.Passenger side rear frame body
mount bracket to rear underbody
.Passenger side center frame
body mount bracket to center
underbody
.Exhaust pipe hanger rod to rear
frame
SEO Available
Options
Dual Battery System -
SEO 6A6
This vehicle may have a dual
battery system. The two batteries
are connected so that both supply
battery power to the vehicle at the
same time
—they are connected in
parallel. See “Battery”in the owner
manual for additional information
on batteries.
