2013 BMW M6 COUPE change time

Active Blind Spot Detection
The concept
Two radar sensors below the rear bumper
monitor the area behind and next to the vehicle
at speeds above approx. 30 mph/50 km/h.
The system indicates whether there are vehi‐
cles in the blind spot, arrow 1, or approaching
from behind on the adjacent lane, arrow 2.
The lamp in the exterior mirror housing lights
up dimly.
Before you change lanes after setting the turn
signal, the system issues a warning in the sit‐
uations described above.
The lamp in the housing of the exterior mirror
flashes and the steering wheel vibrates.
Notes Personal responsibility
The system does not serve as a substi‐
tute for the driver's personal judgment of the
traffic situation.
Be aware of the traffic situation and the vehi‐
cle's surroundings at all times, otherwise an
accident is still possible despite all warnings.◀
At a glance
Button in the vehicle
Active Blind Spot Detection
Radar sensors
The radar sensors are located under the rear
bumper.
Switching on/off Press the button.
▷On: the LED lights up.▷Off: the LED goes out.
The system can issue warnings at speeds
above approx. 30 mph/50 km/h.
The state is stored for the remote control cur‐
rently in use.
Seite 109SafetyControls109
Online Edition for Part no. 01 40 2 910 796 - VI/13

Maximum coolingPress the button.
The system is set to the lowest tem‐
perature, maximum air flow and air circulation
mode.
Air flows out of the vents for the upper body
region. The vents need to be open for this.
Air is cooled as quickly as possible:▷At an external temperature of approx.
32 ℉/0 ℃.▷When the engine is running.
The air volume can be adjusted when the pro‐
gram is active.
Automatic recirculated-air control/recirculated-air mode
You can respond to unpleasant odors or pollu‐
tants in the immediate environment by tempo‐
rarily suspending the supply of outside air. The
system then recirculates the air currently
within the vehicle.
Press the button repeatedly to select
an operating mode:
▷LEDs off: outside air flows in continuously.▷Left LED on, automatic recirculated-air
control: a sensor detects pollutants in the
outside air and controls the shutoff auto‐
matically.▷Right LED on, recirculated-air mode: the
supply of outside air into the vehicle is per‐
manently blocked.
If the windows are fogged over, switch off the
recirculated-air mode and press the AUTO
button on the driver's side to utilize the con‐
densation sensor. Make sure that air can flow
onto the windshield.
Continuous recirculated-air mode
The recirculated-air mode should not be
used for an extended period of time, as the air
quality inside the vehicle deteriorates stead‐
ily.◀
Cooling function
The passenger compartment can only be
cooled with the engine running.
Press the button.
The air is cooled and dehumidified
and – depending on the temperature setting –
warmed again.
Depending on the weather, the windshield may
fog up briefly when the engine is started.
The cooling function is switched on automati‐
cally with the AUTO program.
When using the automatic climate control,
condensation water, refer to page 151, devel‐
ops that exits underneath the vehicle.
Rear window defroster Press the button.
The rear window defroster switches
off automatically after a certain period of time.
SYNC program Press the button.
Current settings on the driver's side
for the temperature, air volume, air distribution,
and AUTO program are transferred to the front
passenger side.
The program is switched off if the settings on
the front passenger side are changed.
Residual heat
The heat stored in the engine is used to heat
the interior.
Functional requirement▷Up to 20 minutes after the engine has been
switched off.▷Warm engine.▷The battery is sufficiently charged.▷External temperature below 77 ℉/25 ℃.Seite 132ControlsClimate control132
Online Edition for Part no. 01 40 2 910 796 - VI/13

erases all programming of the buttons on
the interior rearview mirror.3.Hold the hand-held transmitter for the sys‐
tem to be controlled approx. 1 to 3 in/2.5 to
8 cm away from the buttons on the interior
rearview mirror. The required distance de‐
pends on the manual transmitter.4.Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program‐
med on the interior rearview mirror. The
LED on the interior rearview mirror will be‐
gin flashing slowly.5.Release both buttons as soon as the LED
flashes more rapidly. When the LED is
flashing faster, this indicates that the but‐
ton on the interior rearview mirror has been
programmed.
If the LED does not flash faster after at
least 60 seconds, change the distance be‐
tween the interior rearview mirror and the
hand-held transmitter and repeat the step.
Several more attempts at different distan‐
ces may be necessary. Wait at least
15 seconds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the
hand-held transmitter button for 2 sec‐
onds.6.To program other functions on other but‐
tons, repeat steps 3 to 5.
The systems can be controlled using the inte‐
rior rearview mirror buttons.
Special feature of the alternating-
code wireless system
If you are unable to operate the system after
repeated programming, please check if the
system to be controlled features an alternat‐
ing-code system.
Read the system's operating manual, or press
the programmed button on the interior rear‐
view mirror longer. If the LED on the interior
rearview mirror starts flashing rapidly and then
stays lit constantly for 2 seconds, the system
features an alternating-code system. Flashing
and continuous illumination of the LED will re‐
peat for approximately 20 seconds.
For systems with an alternating-code system,
the integrated universal remote control and the
system also have to be synchronized.
Please read the operating manual of the sys‐
tem being set up for information on how to
synchronize the system.
Synchronizing is easier with the aid of a sec‐
ond person.
To synchronize:1.Park the vehicle within range of the re‐
mote-controlled system.2.Program the relevant button on the interior
rearview mirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the
interior rearview mirror for approximately
3 seconds and then release it. If necessary,
repeat this work step up to three times in
order to finish synchronization. Once syn‐
chronization is complete, the programmed
function will be carried out.
Reprogramming individual buttons
1.Switch on the ignition.2.Press and hold the interior rearview mirror
button to be programmed.3.As soon as the interior rearview mirror LED
starts flashing slowly, hold the hand-held
transmitter for the system to be controlled
approx. 1 to 3 in/2.5 to 8 cm away from the
buttons on the interior rearview mirror. The
required distance depends on the manual
transmitter.Seite 136ControlsInterior equipment136
Online Edition for Part no. 01 40 2 910 796 - VI/13

the service center if you are unfamiliar with
them or they are not described here.
You can obtain a selection of replacement
bulbs at the service center.
Danger of burns
Only change bulbs when they are cool;
otherwise, there is the danger of getting
burned.◀
Working on the lighting system
When working on the lighting system,
you should always switch off the lights af‐
fected to prevent short circuits.
To avoid possible injury or equipment damage
when replacing bulbs, observe any instructions
provided by the bulb manufacturer.◀
Do not perform work/bulb replacement
on xenon headlamps
Have any work on the xenon lighting system,
including bulb replacement, performed only by
a service center. Due to the high voltage
present in the system, there is the danger of
fatal injuries if work is carried out improperly.◀
Do not touch the bulbs
Do not touch the glass of new bulbs with
your bare hands, as even minute amounts of
contamination will burn into the bulb's surface
and reduce its service life.
Use a clean tissue, cloth or something similar,
or hold the bulb by its base.◀
Light-emitting diodes (LEDs)
Light-emitting diodes installed behind a cover
serve as the light source for controls, display
elements and other equipment.
These light-emitting diodes, which are related
to conventional lasers, are officially designated as Class 1 light-emitting diodes.Do not remove the covers
Do not remove the covers, and never
stare into the unfiltered light for several hours;
otherwise, irritation of the retina could result.◀
Headlamp glass
Condensation can form on the inside of the ex‐
ternal lamps in cool or humid weather. When
driving with the light switched on, the conden‐
sation evaporates after a short time. The head‐
lamp glasses do not need to be changed.
If the headlamps do not dim despite driving
with the light switched on, increasing humidity
forms, e. g. water droplets in the light, have the
service center check this.
Headlamp setting
The headlamp adjustments can be affected by
changing lamps and bulbs. Therefore after a
change, have the headlamp setting checked
and corrected by Service.
Xenon headlamps
Hints
Because of the long life of these bulbs, the
likelihood of failure is very low. Switching the
lamps on and off frequently shortens their life.
Do not perform work/bulb replacement
on xenon headlamps
Have any work on the xenon lighting system,
including bulb replacement, performed only by
a service center. Due to the high voltage
present in the system, there is the danger of
fatal injuries if work is carried out improperly.◀
For checking and adjusting headlamp aim,
please contact your BMW center.
Light-emitting diodes (LEDs)
Follow the general instructions on Lamps and
bulbs, refer to page 178.
With Xenon-headlamps, the following lamps
are designed with LED technology:Seite 179Replacing componentsMobility179
Online Edition for Part no. 01 40 2 910 796 - VI/13

Brake pads, breaking in 148
Braking, hints 150
Breakdown assis‐ tance 184, 185
Breaking in 148
Brightness of Control Dis‐ play 87
Bulb replacement, front 178
Bulb replacement, rear 180
Button, Start/Stop 59
Bypassing, refer to Jump- starting 186
C
California Proposition 65 Warning 7
Calling up mirror adjust‐ ment 39
Calling up seat adjust‐ ment 39
Calling up steering wheel ad‐ justment 39
Camera, backup camera 122
Camera, care 193
Camera, Side View 126
Camera, Top View 125
Can holder, refer to Cu‐ pholder 142
Car battery 182
Carbon ceramic brake M 146
Car care products 191
Care, displays 193
Care, vehicle 191
Cargo 152
Cargo area lid 36
Cargo area, storage compart‐ ments 143
Cargo, securing 153
Cargo straps, securing cargo 153
Car key, refer to Remote con‐ trol 30
Carpet, care 193
Car wash 190 Catalytic converter, refer to
Hot exhaust system 149
CBS Condition Based Serv‐ ice 176
CD/Multimedia, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
Center console 14
Center-Lock, see button for central locking 33
Central locking system 33
Central screen, refer to Con‐ trol Display 16
Ceramic brake 146
Changes, technical, refer to Safety 7
Changing parts 178
Changing wheels 181
Changing wheels/tires 165
Check Control 75
Checking the oil level elec‐ tronically 172
Children, seating position 55
Children, transporting safely 55
Child restraint fixing sys‐ tem 55
Child restraint fixing system LATCH 56
Child restraint fixing systems, mounting 55
Child seat, mounting 55
Child seats 55
Chrome parts, care 192
Cigarette lighter 137
Cleaning, displays 193
Climate control 130
Climate control laminated tinted safety glass 149
Climate control wind‐ shield 149
Clock 78
Closing/opening from in‐ side 36 Closing/opening via door
lock 35
Closing/opening with remote control 34
Clothes hooks 142
Collision warning with City Braking function 100
Combination switch, refer to Turn signals 70
Combination switch, refer to Wiper system 71
Comfort Access 37
Compound brake 146
Compressor 166
Computer 84
Condensation on win‐ dows 131
Condensation under the vehi‐ cle 151
Condition Based Service CBS 176
Confirmation signal 39
ConnectedDrive, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
ConnectedDrive Services
Control Display 16
Control Display, settings 86
Controller 16
Control systems, driving sta‐ bility 113
Convenient opening 34
Coolant 175
Coolant temperature 78
Cooling function 132
Cooling, maximum 132
Cooling system 175
Corrosion on brake discs 150
Cruise control 117
Cruising range 79
Cupholder 142
Current fuel consumption 79 Seite 201Everything from A to ZReference201
Online Edition for Part no. 01 40 2 910 796 - VI/13

D
Damage, tires 164
Damper control 115
Damper Control, Elec‐ tronic 115
Data, technical 196
Date 78
Daytime running lights 89
Defrosting, refer to Windows, defrosting 131
Departure time, parked-car ventilation 134
Destination distance 84
Differential lock 115
Digital clock 78
Digital speed 78
Digital tachometer 78
Dimensions 196
Dimmable exterior mirrors 52
Dimmable interior rearview mirror 52
Direction indicator, refer to Turn signals 70
Display in windshield 127
Display lighting, refer to In‐ strument lighting 91
Displays 74
Displays, cleaning 193
Disposal, coolant 175
Disposal, vehicle battery 182
Distance control, refer to PDC 119
Distance to destination 84
Divided screen view, split screen 20
Door lock, refer to Remote control 30
Doors, Automatic Soft Clos‐ ing 36
Double-clutch transmis‐ sion 65
Drivelogic 67
Drive mode 66
Drive-off assistant 113 Drive-off assistant, refer to
DSC 113
Driver assistance, see Intelli‐ gent Safety 99
Driving Assistant, see Intelli‐ gent Safety 99
Driving Dynamics Control 69
Driving Dynamics System 80
Driving dynamics, system states 80
Driving instructions, breaking in 148
Driving notes, general 149
Driving on racetracks 147
Driving program, refer to Drivelogic 67
Driving stability control sys‐ tems 113
Driving tips 149
DSC Dynamic Stability Con‐ trol 113
Dynamic Stability Control DSC 113
E
EDC, Electronic Damper Con‐ trol 115
EfficientDynamics 80
EfficientDynamics display 80
EfficientDynamics menu 80
Electronic Damper Control EDC 115
Electronic displays, instru‐ ment cluster 75
Electronic Stability Program ESP, refer to DSC 113
Emergency detection, remote control 31
Emergency release, door lock 36
Emergency release, fuel filler flap 158
Emergency Request 184
Emergency service, refer to Roadside Assistance 185 Emergency start function, en‐
gine start 31
Emergency unlocking, trunk lid 37
Energy Control 79
Energy recovery 79
Engine, automatic Start/Stop function 61
Engine, automatic switch- off 61
Engine compartment 170
Engine compartment, work‐ ing in 170
Engine coolant 175
Engine oil 172
Engine oil, adding 173
Engine oil additives 173
Engine oil change 174
Engine oil filler neck 173
Engine oil temperature 77
Engine oil types, alterna‐ tive 173
Engine oil types, ap‐ proved 173
Engine start during malfunc‐ tion 31
Engine start, jump-start‐ ing 186
Engine start, refer to Starting the engine 60
Engine stop 61
Engine temperature 77
Entering/exiting vehicle, as‐ sistance, steering wheel 53
Entering a car wash 190
Equipment, interior 135
ESP Electronic Stability Pro‐ gram, refer to DSC 113
Exchanging wheels/tires 165
Exhaust system 149
Exterior mirror, automatic dimming feature 52
Exterior mirrors 51
External start 186
External temperature dis‐ play 78 Seite 202ReferenceEverything from A to Z202
Online Edition for Part no. 01 40 2 910 796 - VI/13

Signals when unlocking 39
Sitting safely 45
Size 196
Ski bag 139
Smallest turning circle 197
Smoker's package 137
Snow chains 169
Socket 138
Socket, OBD Onboard Diag‐ nostics 177
SOS button 184
Spare fuse 182
Speaker lighting 92
Specified engine oil types 173
Speed, average 84
Speed limit detection, on‐ board computer 85
Speed limiter, display 82
Speed Limit Information 82
Speed limit in the com‐ puter 85
Split screen 20
Stability control systems 113
Standard view, head-up dis‐ play 128
Start/stop, automatic func‐ tion 61
Start/Stop button 59
Start function during malfunc‐ tion 31
Starting the engine 60
Status display, tires 96
Status information, iDrive 19
Status of Owner's Manual 6
Steering assistance 116
Steering wheel, adjusting 53
Steering wheel heating 53
Steering wheel memory 50
Stopping the engine 61
Storage compartments 140
Storage compartments, loca‐ tions 140
Storage, tires 166
Storing the vehicle 193
Summer tires, tread 164 Supplementary text mes‐
sage 76
Surround View 121
Switch, refer to Cockpit 12
Symbols 6
SYNC program, automatic cli‐ mate control 132
System states of the driving dynamics 80
T
Tachometer 77
Tail and brake lamps 180
Tailgate 36
Tailgate via remote con‐ trol 34
Tail lamps 180
Tail lamps, bulb replace‐ ment 180
Technical changes, refer to Safety 7
Technical data 196
Technology, BMW M 146
Telephone, see user's manual for Navigation, Entertain‐
ment and Communication
Temperature, automatic cli‐ mate control 131
Temperature display, external temperature 78
Temperature, engine oil 77
Terminal, starting aid 186
Text message, supplemen‐ tary 76
Theft alarm system, refer to Alarm system 40
Theft protection, refer to Central locking system 33
Thermal camera, refer to Night Vision 104
Thigh support 46
Tilt alarm sensor 41
Tilt glass roof 42
Tilt, seats 45
Time of arrival 85 Tire damage 164
Tire identification marks 163
Tire inflation pressure 161
Tire inflation pressure moni‐ tor, refer to FTM 98
Tire Pressure Monitor TPM 96
Tires, changing 165
Tire sealant 166
Tires, everything on wheels and tires 161
Tire tread 164
Tone, see user's manual for Navigation, Entertainment
and Communication
Tools 178
Top View 124
Total vehicle weight 197
Tow fitting 188
Towing 187
Tow-starting 187
Tow truck 187
TPM Tire Pressure Moni‐ tor 96
Transmission positions 65
Transporting children safely 55
Tread, tires 164
Trip computer 85
Triple turn signal activa‐ tion 70
Trip odometer 78
Truck for tow-starting/ towing 187
Trunk lid 36
Trunk lid, emergency unlock‐ ing 37
Trunk lid, hotel function 37
Trunk lid via remote con‐ trol 34
Turning circle 197
Turning circle lines, rearview camera 123
Turn signals, operation 70
Turn signals, rear, bulb re‐ placement 180 Seite 207Everything from A to ZReference207
Online Edition for Part no. 01 40 2 910 796 - VI/13