2013 AUDI S8 winter tires

90 On the road
Messages in the instrument cluster
display
Applies to vehicles: with S ta rt-Stop-System
Start-S top sy stem de activated: Pl ea se re­
s ta rt engine manually
This message appears when specific condi­
tions are not met dur ing a stop phase and t he
Start -Stop -System will
not be ab le to restart
the engine.
If the D or R se lector lever posi­
t ions were engaged,
P will be selected auto ­
m atica lly. The engine must be started with
the
! START ENGIN E STOPI button .
Start-Stop system : Sy stem fault! Function
un available
There is a malfunc tion in the Sta rt-Stop-Sys­
tem . Dr ive the vehicle to an au thorized repair
fac ility for servicing as soon as possible to cor­
rect the malfunction.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed .
The speed warning system warns you if you
are exceeding the maximum speed that you
have set . You will hear a warn ing tone when
your speed exceeds the stored value by ap­
p rox imately 3 mph (3 km/h) . An indicato r
l ig ht . (USA models)/ . (Canada mode ls) i n
the ins trumen t clus ter display also t urns on at
the same time . The ind icator light
a;m
turns off when the speed decreases below the
stored maximum speed.
Se tting a thresho ld is re commended if yo u
wo uld like to be reminded when you reach a
certain maximum speed. Situations where you may want to do so include driv ing in a country
with a general speed Limit or if there is a
specified max imum speed for winter tires .
@ Tips
Even though your vehicle is equipped with
a speed warning system, you should st ill watch the speedome
ter to ma ke s ure you
are not dr iving faster than the speed limit .
Setting the threshold
You can set, chang e and delet e the threshold
in the MMI.
• Select: I CAR I func tion button > Car sy stem s
contro l but to n > Driver a ssist > Speed warn­
ing .
You can set any threshold betwee n 20 mph
(30 km/h) and 150 mph (2 40 km/h). Se tting s
can each be adj usted in incremen ts of
5 mph
(10 km/h).
Cruise control
Switching on
The cruise con trol sys tem makes it possible to
drive at a constant speed starting at 20 mph (30 km/h) .
Fig. 91 Contro l leve r wit h set b utton
Fi g. 92 D isp lay : Se lecte d sp ee d
• Pull the lever to position@~ fig. 91 to
s w itch the system on.
• Dr ive at the speed you w is h to set .
.,. Press button @to set that speed.

Driving with your
quattro ®
With All Wheel Drive, all four wheels are driv­
en .
Gene ral inform ation
W ith All Whee l Drive, power is distributed to
all four wheels . This happens automatically
depending on your driving style and the road
conditions at the t ime. See also
t::;> page 198.
W ith the spo rt differential*, power d istribu­
tion to the rear wheels is variable and can be
adj usted with Aud i drive select*
t::;> page 109.
Always read and fo llow safety precautions
c:> .&. .
Winter t ires
When driving in the winter , your vehicle with
All Wheel Dr ive has an advantage, even with
regular t ires. In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­ ing: these tires must be mounted on
a ll four
w he els .
See also c:> page 264, Winter tires.
Sn ow cha ins
Where snow cha ins a re mandatory on certa in
roads, th is normally a lso applies to vehicles
with A ll Wheel Drive
c:> page 265, Snow
chains .
Replacing whe els/ tires
Vehicles w ith All Whee l Dr ive must always
have tires of the same size. Also avoid t ires
with different tread depths. For details see
page
c:> page 260, New tires and replacing
tires and wheels .
Off-Road driving?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle.
It is
therefore best to avoid rough tracks and un ­
even terrain as much as possible. Also refer to
c:> page207.
Int ellig ent technolog y 203
A WARNING
Always adjust your driv ing to road and traf­
fic conditions. Do not let the extra safety
afforded by All Wheel Dr ive tempt you into
taking extra risks .
- Although the All Wheel Drive is very ef­
fective, always remember that braking capacity is lim ited by tire t raction. You
should therefore not d rive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
drive too fast because the fron t wheels
could begin to slide on top of the water (aquaplaning) . If this should occur, yo u
will have no warning from a s udden in­
crease in engine speed as w ith a front­
wheel drive veh icle. Always drive at
speeds which are su ited to the road con­
ditions - risk of crash.
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting
the engine .
If a vehicle with a conve ntiona l energy system
is not drive n for a long per iod of t ime, the bat­
tery is discharged by idling current consume rs
(e.g . immobilizer). In certain circumstances it
can resu lt in the re being insuff icient energy
available to start the engine.
Intelligent energy management in your vehi­
cle handles the distribution of e lectrica l ener­
gy. Starting ability is marked ly improved and
the life of the battery is extended.
Basica lly, energy management consists of
b atte ry diagno sis, i dling current man age­
ment
and d y namic ene rg y management .
Battery diagno sis
Battery diagnosis continuously determines
the sta te of the battery. Sensors determine
battery voltage, battery current and battery
Ii),,
•
•

250 Tire s and wheel s
-Never mount used tires on yo ur vehicle if
you are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden t ire failure
and loss of vehicle control.
- If you notice unusual vibration or if the
vehicle pulls to one side when driving, al­
ways stop as soon as it is safe to do so
and check the wheels and tires for dam­
age.
(D Note
Please note that summer and wi nte r tires
are designed for the cond itions that are
Glossary of tire and loading terminology
Accessory weight
means t he comb ined we ight (in excess of
those sta ndard items which may be rep laced)
of au toma tic tra nsmission, power steer ing,
power brakes, power windows, power seats,
radio, and heater, to the extent that th ese
items are availab le as factory -installed equip­
ment (whether installed or not) .
Aspect ratio
means t he ratio of the he ight to the w idth of
the tire in percent . Numbers of 55 or lower in ­
dicate a low sidewall for improved steering re­
sponse and better overall handling on dry pavement .
Bead
means the part of the ti re that is made of
steel wires, wrapped or reinforced by ply cords
and that is shaped to fit the rim.
Bead separation
means a b reakdown of the bond between
components in the bead.
Cord
means the strands forming the plies in the
tire . typ
ica l in those seasons . Aud i recommends
using winter tires during the winter
months . Low temperatures signif icant ly
decrease the e lasticity of summer tires,
which affects tract ion and brak ing ability.
If summer tires are used in very co ld tem­
peratures, cracks ca n form on the tread
bars, res ulting in permanent tire damage
that can cause loud driving no ise and un­
balan ced t ires. Audi is not responsible for
th is type of damage .
Cold tire inflation pressure
means the tire p ressu re recommended by t he
vehicle manufacturer fo r a tire of a des igna ted
s iz e that has not bee n driven for more than a
coup le of miles (k ilometers) at low speeds in
t h e three hour period before the tire pressure
is measured or adjusted.
Curb weight
mea ns the we ight of a motor ve hicle with
standard equipment in cl uding the max imum
capacity of fuel, oil, and coolant, air condi ­
tioning and additional weight of optiona l
equipment.
Extra load tire
me ans a t ire design to operate at higher loads
and at h igher inflation pressures than the cor­
responding standard tire . Extra load tires may
be identified as "XL", "x l" , "EXTRA LOAD", or
"RF" on the sidewall.
Gross A xle Weight Rating ("GAWR ")
means the lo ad -c a rry ing c apac ity of a s ingle
axle system , measured a t the tire-ground in­
terfaces.
Gross Vehicle Weight Rating ("GVWR ")
mea ns the maximum total loaded we ight of
t h e ve hicl e. .,.

252 Tires and wheels
Speed rating (letter code)
means the speed at wh ic h a tir e is des igned to
be d riven for extended per io d s of t ime. The
ratings range from 93 mph (150 km/h) to
186 mph (298 km/h)
¢ page 262 . You may
not find this in format ion on all tires because
it is not required by law.
The speed rating letter code, w here a pplica­
b le, is molded on the tire s idewa ll and indi­
cates the maxim um permissible road speeds
¢ &. in Winter tires on page 265.
Tire pressure monitoring sy stem*
means a system tha t d etects when one or
mo re of a vehicle's t ires are under inflated and
i llum ina tes a low t ire p ress ure warn ing te ll­
tale.
Tread
means t hat port ion of a tire tha t comes into
con tact w it h t he road.
Tread separation
means pull ing away of the t read from the t ire
car cass .
Treadwear indicators (TWI)
means t he projections withi n the pr inc ipal
g rooves designed to give a v isua l ind ication of
the deg rees of wea r of the tre ad . See
¢
pag e 259, Tread W ear Indicator (TWI) for
mo re inf ormat io n on measu ring tire we ar.
Uniform Tire Quality Grading
is a tire i nfo rmation system developed by the
United States Nat io nal Highway Traffic Safety
Admin istration (N HTSA) that is designed to
h e lp buye rs make re lative compa risons among
tires. The UT QG i s no t a safety r ating and no t a
g uar antee that a t ire will las t fo r a presc ribed
n umber of m iles (kilome ters) or pe rform in a
certain way. It s imply gives ti re bu ye rs addi­
tional information to combine with other con -s
iderations, such as p rice , brand loya lty and
dealer recommendations. Un der UTQ G, tires
are grade d by the t ire manufacturers in three
areas : treadwea r, traction, and temperature
resistance. The UTQG informat ion on the tires,
molded into the sidewalls .
U.S. DOT Tire Identification Number (TIN )
This is the tire's "se ria l numbe r" It begins
with the letters "DOT" and ind icates that the
t ire meets all federa l standards . The next two
numbers or letters ind icate the plant where it
was ma nufactu red, and the last four numbe rs
r eprese nt the week and year of ma nufact ure.
Fo r exampl e,
DOT ... 2212 ...
means that the tire was produced in t he 22nd
wee k of 2012. The ot her numbers are market­
ing codes that may or may not be used by the
t ire manufacturer. This information is used to
contact consumers i f a tire defect requires a
r ecall .
Vehicle capacity weight
means the rated cargo and luggage load plus
150 lbs. (68 k ilograms) times the vehicle's to­
ta l seating capacity as listed on the label lo­
cated on the driver's side B-pilla r.
Vehicle maximum lo ad on the tire
means that load on an individua l tire that is
determined by distributing to eac h axle its
share of the maxim um loaded vehicle weight
and divid ing by two .
Vehicle normal load on the tire
means that load on an individua l t ir e that is
determined by distributing to eac h ax le its
share of the curb weight, accessory weight,
and normal occ upant weig ht (d istr ibuted in
accorda nce wit h tab le below ¢
page 253)
and divid ing by two .

262 Tire s and wheels
Speed rating (letter code)
The speed rating letter code on the wheels in­
dicates the maximum pe rmissib le road speeds
¢ & in Winter tires on page 265 .
p up to 93 mph (150 km/h)
Q up to 99 mph (158 km/h)
R up to 106 mph (170 km/h)
s up to 110 mph (180 km/h)
T up to 118 mph (190 km/h)
u up to 124 mph (200 km/h)
H up to 130 mph (210 km/h)
V up to 149 mph (240 km/h)1l
z over 149 mph (240 km/h)1l
w up to 168 mph (270 km/h)1l
y up to 186 mph (298 km/h)1l
Your vehicle is normally factory equipped with
tires, which possess excellent driving charac­
teristics and give your Audi optimum driving
comfort. An electronic speed limiter
<=> page 29 will normally prevent your vehicle
from go ing faster than the tire speed rating
<=> & .
U.S . DOT Tire Identification Numbe r (TIN)
and tire manufacture date
This is the t ire's "serial number". It begins
with the letters "DOT" and indicates that the
tire meets all federal standards. The next two
numbers or letters indicate the plant whe re it
was manufactured, and the last four numbers
represent the week and year of manufacture.
F or example, the numbers 2212 mean the tire
was produced in the 22nd week of 20 12. The
other numbers are marketing codes that may
or may not be used by the t ire manufacturer.
This information is used to contact consumers
if a tire defect requires a recall.
Audi original tire
Tires with the identification "AO" or "RO" have
been specially matched with your Audi. We
recommend using only these tires because
they meet the highest standards regarding
ll For tires wit h a max imum speed capab ility over 149
mph (240 km/h), tire man ufactur ers sometimes use
the letters "ZR."
safety and driving characterist ics when used
correct ly . Your authorized Audi dealer will
gladly provide you w ith more information.
Tire ply composition and materials used
The number of plies indicates the number of
layers of rubber-coated fabric in the tire. In
genera l, the greater the number of plies, the
more weight a tire can support. Tire manufac ­
turers also must indicate the materials in the
tire, which include steel, nylon, polyester, and
others.
Maximum Load Rating
This number indicates the maximum load in
kilograms and pounds that can be carried by
the tire.
Tire quality grading for treadwear,
traction , and temperature resistance
Tread wear, traction and temperat ure grades
<=> page 2 63.
Maximum Permissible Inflation Pressure
Th is number is the greatest amount of air
pressure that should ever be put in the tire
under normal driving conditions.
A WARNING
-Using incorrect or unmatched tires and/
or wheels or improper tire and wheel
comb inat ions can lead to loss of control,
coll is ion and serious personal injury.
- Always use tires, rims and wheel bolts
that meet the specif ications of original
factory- installed tires or other combina­
tions that have been specifically ap­
proved by the vehicle manufacturer.
- T ires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then with specia l care and at lower
speeds.

-Never mount used tires on your vehicle if
you are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
- All four wheels must be fitted with radial
tires of the same type, size (rolling cir­
cumference) and the same tread pattern.
Driving with different tires reduces vehi­
cle handling and can lead to a loss of
control.
- If the spare tire is not the same as the
tires that are mounted on the vehicle -
for example with winter tires - only use
the spare tire for a short period of time and drive with extra care. Refit the nor­
mal road wheel as soon as safely possi­
ble.
- Never drive faster than the maximum
speed for which the tires on your vehicle
are rated because tires that are driven
faster than their rated speed can fail
suddenly.
- Overloading tires cause heat build-up,
sudden tire failure, including a blowout
and sudden deflation and loss of control.
- Temperature grades apply to tires that
are properly inflated and not over or un­
derinflated .
- For technical reasons it is not always
possible to use wheels from other
vehicles - in some cases not even wheels
from the same vehicle model.
- If you install wheel trim discs on the ve­
hicle wheels, make sure that the air flow
to the brakes is not blocked. Reduced air­
flow to the brakes can them to overheat,
increasing stopping distances and caus­
ing a collision.
- Run flat tires may only be used on
vehicles that were equipped with them
at the factory. The vehicle must have a
chassis designed for run flat tires. Incor­
rect use of run flat tires can lead to vehi­
cle damage or accidents. Check with an
authorized Audi dealer or tire specialist
to see if your vehicle can be equipped
Tires and wheels 263
with run flat tires. If run flat tires are
used, they must be installed on all four
wheels. Mixing tire types is not permit­
ted.
@ Note
- For technical reasons, it is not generally
possible to use the wheel rims from oth­
er vehicles. This can hold true for wheels
of the same vehicle type.
- If the spare tire is different from the
tires that you have mounted on your ve­
hicle (for example winter tires or wide
profile tires), then use the spare tire for a
short period of time only and drive with
extra care. Replace the flat tire with the
tire matching the others on your vehicle
as soon as possible.
- Never drive without the valve stem cap .
The valves could get damaged.
(® For the sake of the environment
Dispose of old tires in accordance with the
local requirements.
Uniform tire quality grading
-Tread wear
- Traction AA A B C
- Temperature ABC
Quality grades can be found where applicable
on the tire side wall between tread shoulder
and maximum section width
~ page 260,
fig. 208 .
For example: Tread wear 200, Traction AA,
Temperature A.
All passenger car tires must conform to Feder­
al Safety Requirements in addition to these
grades .
Tread wear
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
unde r contro lled conditions on a specified
government test course. •
•

264 Tire s and wheel s
For example, a tire graded 150 wou ld wear
one and one half (1 1/2) times as well on the
government course as a tire graded
100.
The relat ive perfo rmance of t ires depends
upon the actua l conditions of their use, how ­
ever, and may depart significantly from the norm due to var iat ions in dr iving habits, serv­
ice practices and differences in road character­
istics and climate.
Traction
The traction grades, from highest to lowest,
are AA, A, Band
C. Those grades represent the
tire's ability to stop on wet pavement as
measured under controlled cond it ions on
specif ied government test surfaces of asphalt
and concrete . A tire marked
C may have poor
traction performance
q ,& .
Temp eratu re
The temperature grades are A (the h ighest),
B, and
C, representing the t ire 's resistance to
the generat ion of heat and its ability to dissi­
pate heat when tested under controlled cond i­
tions on a specified i ndoor laboratory test
wheel.
Sustained hig h temperature can cause the
materia l of the tire to degenerate and reduce
tire life, and excessive tempe rature can lead
to sudden ti re failu re
q ,& .
The grade C corresponds to a level of perform­
ance which a ll passenger car tires must meet
u nder the Federa l Moto r Ve hicle Safety Stand­
a rd No.
1 09. G rades Band A represent higher
l eve ls of pe rformance on the labo ratory test
wheel than the m inimum required by law.
A WARNING
T he traction grade assigned to this t ire is
based on straight-ahead b raking traction
tests, and does not incl ude acceleration,
cornering, hydrop lan ing or peak traction
character istics.
A WARNING
The temperature grade for this tire is es­
tablished for a tire that is properly inflated
and not overloaded. Excess ive speed, un­
derinflation, or excessive load ing, either
separa tely or in comb inat ion, can ca u se
h eat bui ld up a nd possib le tire failure.
-
Winter tires
Winter tires can improve vehicle handling on
snow and ice . At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires.
In some heavy snow areas , local gove rnments
may requi re true w in te r or "snow" tires, those
wi th very deeply cut t read . T hese tires sho uld
o n ly be used in pairs and be installed on a ll
fo ur whee ls. Make sure you purchase snow
ti res that are the same size and construction
type as the other tires on your vehicle.
If your vehicle is e quipped w it h all-whee l
drive*, this wi ll improve traction during winter
driving, even with the standa rd tires . Howev ­
er, we strongly recommend that you always
equip all four wheels o n your veh icle w ith cor­
rect ly fitted winter tires or all-season t ires,
when winter road condit ions are expected .
Th is also improves the veh icle's brak ing per­
fo rmance and reduces stoppi ng d ista nces .
Summer tires provide less grip on ice and
snow .
Winter tires (snow tires) must always be fitted on all four wheels .
Ask your authorized A udi dealer or qualified
workshop for permitted
winter ti re size s. Use
on ly rad ial winter tires.
Win ter tires lose their effec tiveness when the
tread is worn down to a depth of
0. 157 inch
(4 mm) .
Only drive w ith w in te r tir es under w inte r con­
di tions. S umme r tires handle bette r when
there is no snow or ice on the roads and the
temperature is above 45
°F (7 °() .

If yo u have a flat tire, see notes on spa re
wheel
¢ page 260 .
P lease always remember th at w inte r ti res may
have a lower speed rating than the t ires origi­
na lly installed on your vehicle at the time it
was manufactured. Please see ¢
page 262,
Speed rating (letter code) for a list ing of the
speed rat ing letter codes and the m aximum
speed at which the tires can be driven .
The speed rating letter code( ¢
page 252) is
on the s ide wall of the tire ¢
page 260.
A WARNING
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed . Always know the maximum
speed before driving off. Never drive faster
than the speed permitted for your specific
w inter t ires. This will cause damage to the
t ires leading to an acc ident and serious
personal in jury to you and yo ur passen­
gers .
& WARNING
Driving faster than the maximum speed
for which the winter tires on your vehicle
were designed can cause tire fai lure in­
cluding a blowout and sudden deflat ion,
loss of control, crashes and serious per­
sonal injuries . Have worn or damaged tires
rep laced immed iate ly .
- Winter tires have max imum speed rat ing
that may be lower than your veh icle's
maximum speed .
- Never drive faster than the speed for wh ich the winter or other tires installed
on your vehicle are rated.
A WARNING
Always adjust your d rivi ng to the road and
t raffic conditions. Neve r let t he good ac­
celeration of the winte r tires and all-whee l
drive tempt you into taking extra r is ks. A l­
ways remember:
Tire s an d wheel s 265
-W hen braking, an a ll-wheel drive vehicle
handles in the same way as a front drive
veh icle.
- Drive carefully and reduce your speed on
icy and slippery roads, even w inter t ires
cannot help under black ice conditions.
@ For the sake of the environment
Use summer tires when weather condi­
tions permit. They are quieter, do not wear
as quickly and reduce fuel consumpt ion.
Snow chains
Snow cha ins may be fitted only to the front
whee ls, and o nly to certain tire sizes . Ask your
authorized Aud i dea le r on which tire sizes
snow c hains can be used.
If you a re go ing to u se snow chains, then you
must install them on the front whee ls at
least.
The snow chains mus t have low-profile links
and must not be th icker than 0 .4 inch
(10,5 mm) , includ ing t he lock.
Remove wheel center covers and trim discs
before putt ing snow cha ins on your vehicle
¢ (D . For safety reasons cover caps must then
be fitted over the wheel bol ts . These a re ava il­
able from autho rized Aud i deale rs .
A WARNING
Usi ng the wrong snow chai ns for your vehi­
cle o r insta lling them incorrect ly can in­
crease the r isk of loss of cont ro l leading to
serious pe rsonal injury.
- Snow chains are available in different
sizes . Always make sure to follow the in ­
structions provided by the snow chain manufacturer .
- When drivi ng with snow chains never
drive faster than the speed permitted for
your specif ic snow chains.
- Always observe local regulations .
•
•