2013 AUDI S8 parking brake

132 Homelink®
Homelink®
Universal remote
control
General information
Applies to vehicles: with Homelink® universal remote
control
The Homelink universal remote control can
be programmed with hand-held transmitters
from existing equipment.
Using the Homelink universal remote control
you can operate equipment such as garage doors, property gates and house l ights from
ins ide your vehicle . '
Using the Homelink universal remote control '
you can replace up to three separate hand-
held transmitte rs for equipment on your
property with just one universal remote con­
trol. Most of these transmitters a re used to
ope rate ga rage doo rs and property g ates. The
individua l transmitters are programmed at
the front bumper. That is where the control
module is located.
The transmi tters must be p rogrammed first in
orde r to operate systems using the Homelink
universal remote control.
A WARNING
- Never use the Homelink ® transmitter
with any garage door opener that does have not the safety stop and reverse fea­
ture as requ ired by federa l safety stand­
ards . T his includes any garage door open­
er model manufact ured before April 1,
1982.
- A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety s tandards . Us ing a ga rage doo r
opener witho ut these fea tures increases
risk of serious injury or death.
- For safety reasons never release the
parking brake or start the engine while
anyone is standing in front of the vehicle .
- A garage door or an estate gate may
sometimes be set in motion when the Homelink
® remote control is being pro­
grammed. If the device is repeatedly ac ­
tivated, th is can overstrain motor and
damage its e lectrica l components - an
overhea ted mo tor is a fire hazard !
- To avo id possib le injuries or property
damage, please always make absolutely
certa in that no persons or ob jects are lo­
cated in the rang e of motion of any
eq uipme nt bei ng ope rated.
(0 Tips
- If you would like add itional information
on the Hom e Link ® Unive rsal Transce iver
'
Home link compatib le p rod ucts, or to
pur chase other acce ssories s uch as the
Homel ink® Light ing Package, please
contact Homelin k at 1-800 -355 -3515 o r
on the Internet at www.homelink .com.
- For Declaration of Comp liance to Unite d
States FCC and Ind ustry Canada reg ula ­
tions ¢
page 299.
'Operation
Applies to vehicles: with Homelink
F ig. 151 Contro l u ni t in the head liner
-"' 8 ± .. .,
Requi rement: The buttons must be program­
med
¢ page 133.
'" Press the p rogrammed button¢&_ in Gen­
eral information on page 132
to open the
ga rage door. The light @will blink or turn
on.
'" Press the b utton again to close the garage
door ¢
&. in General information on
page 132.
~

@ Tips
To open the garage door, press the button,
but do not press it for longer ten seconds
or the Homelink modu le w ill switch to
programming mode .
Programming transmitters
Applies to vehicles : wit h Home link
Fig. 152 Left front a rea o f the bum per
You can program both fixed code and rolling
code systems using these instructions .
Programming a button
.,. Make sure your veh icle is within operating
range of the remote control led garage door
opener.
.,. Set the parking brake
¢ A in General infor ­
mation on page 132.
.,. Switch the ignition on . Do not start the en ­
gine!
.,. There are two ways to program a button :
press the button that you would like to pro ­
gram . The MMI will display instructions to
guide you throug h the programm ing. Or
.,. Select :
I CAR I function button > Car systems
control button > Vehicle settings > Garage
door opener> Program garage door open­
er .
.,. Se lect the button that you wou ld like to
program.
.,. Follow the instructions in the MMI.
.,. If the garage door opening must also be
synchronized w ith the Homelink module ,
refer to the owner's manual for the garage
doo r opener .
Homelink ® 133
Erasing the button programming
.,. Select: !CAR lfunction button> Car systems
function key> Vehicle settings > Garage
door opener
> Clear program settings >
Yes.
Displaying the version/status/country
code
.,. Select: I CAR ! function button > Car systems
control button > Vehicle settings > Garage
door opener > Version information .
Programming a button
T he requ ired distance between the handheld
transmitter and the Homelink modu le in the
bumper depends on the system that you are
programming . When programming a new de ­
vice, keep the button pressed for at least 15
seconds before trying again with the transm it­
ter in a different position .
Each of th e buttons can be reprogrammed in­
dividually . The procedure is the same as for in ­
itial programm ing .¢
page 133 , Programming
a button .
Erasing the button programming
Individual buttons can be reprogrammed. Fol ­
low the same steps used when first program­
ming the button .
If you would like to erase all prog rammed but­
tons at the same time, select Erase button
programming.
@ Tips
- To ensure your safety, eras ing the pro­
grammed Homelink buttons before sell­
ing the vehicle is recommended.
- Depending on the mode l of the garage
door opener, you may need to release the
button on the remote and press it again
when programming .

drive at the maximum permissible speed. Re­
duce your speed even more if load, weather or
wind condit ions are unfavorable -part icularly
when going downhill.
Reduce vehicle speed
immediatel y if the trail­
er shows the slightest sign of swaying .
Do not
try to stop the swaying by accelerating.
Observe speed limits . In some areas, speeds
for vehicles towing trailers are lower than for
regular vehicles .
A lways app ly brakes early. When driving
downhill, shift into a lower gear to use the en­
gine braking effect to slow the vehicle . Use of
the brakes a lone can cause them to overheat
and fail.
Coolant temperature
The coolant temperature gauge c:> page 10
must be observed carefully. The coo lant tem­
perature can increase if you drive on long in ­
clines in a low gear at high engine speeds. Re­
duce your speed immed iate ly if the L EDs in
the top part of the display turn on.
F or more information about indicator lights,
refer to. ~
page 16.
A WARNING
Anyone not properly restrained in a mov­
ing vehicle is at a much greater risk in an
accident . Never let anyone r ide in your car
who is not properly wear ing the restra ints
provided by Aud i.
Trailer towing tips
Important to know
Your veh icle hand les different ly when tow ing
-
a trailer because of the addit ional weight and
d ifferent weight distribution . Safety, perform­
ance and economy will greatly depend on how
carefully you load your trailer and operate
your ng .
Before you actually tow your trailer, practice
turning, stopping and backing up in an area
away from traffic. Keep practicing until you
Trailer towing 213
have become completely familiar with the way
your vehicle-trai ler combination behaves and
responds.
Backing up is difficult and requires practice .
Backing up with a t railer generally requires
steering action opposite to that when backing
up your vehicle without a tra iler.
Maintain a greater distance between your ve­
hicle and the one in front of you . You wi ll need
more room to stop. To compensate for the
trailer, you w ill need a larger than normal
turning radius.
When passing, remembe r that you cannot ac­
ce lerate as fast as you norma lly would be­
cause of the added load. Make sure you have
enough room to pass. After passing, allow plenty of room for your trailer before chang­
ing lanes again.
Avoid jerky starts, sharp turns or rapid lane changes.
(D Tips
- Do not tow a trailer during the break-in
period of your vehicle.
- If you tow a trailer, your Audi may re ­
quire more frequent maintenance due to
the extra load
c:> page 296.
Parking on a slope
Do not park on a slope with a trailer. If it can­
not be avoided, do so only a~er doing the fol­
lowing:
When parking:
.,. App ly the foot brake.
.,. Have someone p lace chocks under both the
vehicle and the trailer wheels .
.,. With chocks in place, slowly release the
brakes until the wheel chocks absorb the
load.
.,. Turn the wheels towards the curb .
.,. Apply the parking brake .
.,. Select the P selector lever posit ion .
When restarting after parking:
.,. Apply the foot brake.
•
•

232 Checking and filling
Checking and filling Engine hood
Releasing the engine hood
The engine hood is released from inside the
vehicle .
Fig. 193 Driver foo twell: release lever
AUD I
Fig. 194 Rocker switch un der the hood
Make sure the wiper arms are not raised up
from the windshield. Otherwise the paint
could be damaged .
.,. Pull the lever under the instrument panel in
the direction of the arrow
~ fig. 193.
.,. Raise the hood slightly~,&. .
... Press the rocker switch under the hood up­
ward
~ fig. 194. This releases th e catch.
... Open the hood.
&_ WARNING
Hot engine coolant can burn you.
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine compartment . Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood .
' Working in the engine compartment
Be especially careful whenever you work in
the engine compartment.
Whenever you must perform any work in the
engine compartment, for example checking
and filling different fluids, there is a risk of injury, burns and accidents. To prevent per­
sonal injury always observe the following
WARNINGS. The engine compartment of any
vehicle is a hazardous area
~ ,&. .
A WARNING
To help avoid injury, before you check any­
thing under the hood:
- Turn off the engine.
- Switch off the ignition .
- Apply the parking brake.
- Move selector lever to "P" (Park) .
- Always let the engine cool down. Hot
components will burn skin on contact.
- To reduce the risk of being burned, never
open the hood if you see or hear steam
or coolant escaping from the engine
compartment. Wait until no steam or
coolant can be seen or heard before care­
fully opening the hood.
- Keep children away from the engine com­
partment.
- Never spill fluids on hot engine compo­
nents . They can cause a fire .
- Never touch the radiator fan. The auxili­
ary electric fan is temperature controlled
and can switch on suddenly .
- Never open the coolant reservoir cap
when the engine is still warm . The cool­
ant system is pressurized and hot cool­
ant could spray out.
- Protect your face, hands and arm from
steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir.
- Do not remove the engine cover under
any circumstances. This increases the
risk of burns.
- If work on the fuel system or the electri­
cal system is necessary:

-Always disconnect the battery.
- Never smoke or work near heaters or open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch :
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the engine running:
- First, fully apply the parking brake,
move selector lever to "P" (Park).
- Always use extreme caution to prevent
clothing, jewelry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts. Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine.
- Minimize exposure to emission and
chemical ha zards c:::> & .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition ,
certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm .
Checking and filling 233
-Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam­
age to vehicle systems will occur.
(® For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly . If
you see spots from oil or other vehicle flu­ ids, have your vehicle inspected by an au­
thorized Audi dealer.
Closing the engine hood
.,. Pull the hood down until the pressure from
the struts is reduced.
"' Let the hood
drop down and latch in place.
Do not try to push it shut; it may fail to en­
gage
c:::> ,A .
A WARNING
-
A hood that is not completely latched
could fly up and block your view while driv ­
ing .
- When you close the engine hood, check it
to make sure the safety catch has proper­ ly engaged. The hood should be flush
with the surrounding vehicle body parts.
- If you notice while driving that the hood
is not secured properly , stop at once and
close it. •
•

Spare wheel
Applies to vehicles: with spare wheel
The spare wheel is stored in the wheel well
underneath the floor panel in the luggage
compartment.
F ig. 21 6 Luggag e compartme nt: spare wheel
Taking out the sp are whee l
• Lift the cargo floor by the plast ic handle
c:> fig . 216.
• Hook the hand le into the luggage compart ­
ment weather strip .
• Turn the large screw
c:> fig. 216 counter­
clockwise.
• Take out the spare tire.
• Always store the vehicle tool kit, the jack*
and the replaced tire i n the luggage com­
partment
c:> page 140 .
• Unhook the ca rgo floor before closing the
rear lid.
& WARNING
Loose items in the passenger compa rt­
ment can cause serious pe rsonal in jury
during hard braking or in an accident.
- Never store the spare wheel or jack and
tools in the passenger compartment.
@ Tips
Check the inflat io n press ure of the spare
tire periodically to keep the tire ready for
use.
-
What do I d o now ? 273
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel.
• After you experience a tire failure, pull the
car well away from mov ing traffic and try to
reach
le vel ground before you stop c:> ,&.
• All passengers should leave the car and
move to a safe location (for ins tance, behind
t he guardra il)
c:> ,& .
• Engage the parking brak e to prevent your
vehicle from rolling unintentionally
c:> ,& .
• Move sele ctor lever to po sit ion Pc:> &_ .
• If you are towing a trailer, unhitch the trail­
er from your vehicle.
• Take the
jack and the spare tire out of the
luggage compartment
c:> page 271,
c:> page
272 .
& WARNING
You o r you r passengers could be i njured
while changing a wheel if you do not fo l­
low these safe ty pre caut ions :
-I f you have a flat tire, move a safe d is­
tance off the road. Turn off the e ngine,
turn the emergency flashers on and use
other warning devices to a lert other mo­
torists .
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possib ly slipping off the
jack, always full y set the parking brake
a nd b lock the wheel d iagonally opposite
the wheel be ing changed. When one
front wheel is lifted off the ground, plac­ ing the Au tomatic Transmission in "P"
( P ar k) will
not prevent the vehicle from
mov ing .
- Before you chang e a whee l, be s ure the
g round is level and firm. If necessary,
use a sturdy board un der the jac k.
-

276 What do I do n ow ?
ho ld on to the car to keep your ba lance
and take care not to slip .
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed .
Fig. 220 Sill panels : m ark ings
Fig . 22 1 Sill: posit ion ing t he veh icle jack
.. Activate the vehicle jack mode in the MMI:
I CAR ! function button > Ca r sys tem s control
button>
S ervicing & checks > Air susp .:
jack mod e > On .
.. Engage the parking brake to prevent your
vehicle from ro lling u ninten tionally.
.. Move the
se lector l ever to po siti on P .
.. Find the marking (imprint) on the sill that
is nearest the wheel that will be changed
o
fig. 220 . Behind the marking, there is a
lifting point on the s ill for the vehicle jack .
.. Turn the
ve hicle jack located under the lift­
ing point on the si ll to raise the jack until its
arm @o
fig. 221 is located under the des ­
i gnated plastic mount o ,& o0.
.. Align the jack so that its arm@o
fig. 221
engages in the designated lifting po int in
the door sill and the movable base @ lies
flat on the gro und. The base @ must be
ver­
tical
under the lifting point @. ..
Wind the jack up fu rther until the f lat t ire
comes off the ground o
.&,.
Position t he vehicle jack only under the desig ­
nated lifting points on the si ll
c:> fig. 220.
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other location
c:> .&, c:>Q).
An un stable surfac e under the jack ca n cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or simi lar support
under the jack. On
hard, slipper y surfaces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
c:> .&, .
A WARNING ~
-You or your passengers co uld be injured
while changing a wheel if you do no t fo l­
low these safety p reca utio ns:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack co uld
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always prov ide a firm base for
the jack on the ground. If necessa ry,
u se a st urdy boa rd under the jack.
- On hard, s lippery su rface (such as t iles)
use a rubber mat or sim ilar to prevent
the jack from slipping.
- To help prevent injury to yo urself and
your p asse ngers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic .
- Make sure jack pos ition is correct, ad ­
just as necessary and then continue to
raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.

Fuse s and bulb s 281
Luggage compartment fuse assignment
Fig. 228 Luggage compartment: fuse pa nel with plastic bracket
Fuse panel @ (black ) Fuse panel @ (b la ck)
No . Equi pment Amps No. Equipment Amps
[ru button, data logger, diag-
11 Dynamic
steering
5
l nostic
connector, BCM -1,
5
Selector lever, BCM-2 5
adaptive light ing system
Audi side assist
5
2 Networking gateway 5
Engine control module 5
3 adaptive air suspension
5
Starter 40
4 Parking system 5
Left headlight/Headlight
16 10/5
5 Steer
ing column lever
5
range control system
6 Suspension control system
5 Fuse panel
@ (red ) sensor
Belt tensioners, airbag con-
No. Equipment Amps
7 trol module 5
l Left
reversible be lt tens ione r 25
Heated washer fluid nozzles, 2
Right reversible belt ten-
25
Homelink (garage door sioner
8 opener), night vision system 5 Starter diagnos
is, DC/DC
control module, sport differ-3 c onverter (Start-Stop-Sys-5
ential, ioni zer tern )
9
Electromechan ica l parking
5 4 DC/DC converter 7,5
brake contro l modu le 5 Image pro cessing 7 ,5 -
10
Rear seat heating, cooler, in-
5
terior rearview mirror