-If swallowed and person is conscious,
rinse mouth with water for at least 15
minutes . Do not induce vomiting unless
instructed to do so by medical professio
nal. Get medical attention immediately.
(D Note
Liquid electrolyte leaking from broken mir
ror glass will damage any plastic surfaces
it comes in contact with . Clean up spilled
electrolyte immediately with clean water
and a sponge.
@ Tips
- Switching off the dimming function of
the inside rear view mirror also deacti
vates the automatic dimm ing function of
the exterior mirrors .
-Automatic dimming for the mirror only
operates properly if the light striking the
inside mirror is not hindered by other ob
jects.
- The automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected .
Sun visors
._[ _ __,!
Fig. 63 Driver's s ide: s un visor
The sun visors for the driver and passenger
can be pulled out of their brackets in the cen
ter of the vehicle and turned towards the
doors
(D .
The mirror light switches on when the cover
over the vanity mirror @opens .
Clear vision 5 7
Wiper and washer
system
Switching the windshield wipers on
Fig. 64 Win dshi eld w ipe r leve r
Move the windshield wiper lever to the corre
sponding position:
@-Windshield wiper off
CD-Interval mode . To extend/shorten the
wiper intervals, move the switch @to the
left/right. In vehicles with a rain sensor* the
wipers turn on in the rain once the vehicle
speed exceeds approximately 2 mph (4 km/h) .
The higher the sensitivity of the rain sensor* is
set (switch @to the right), the earlier the
windshield wipers react to moisture on the
windshield. In some models, you can switch
rain sensor mode off and switch intermittent
mode on in the MMI* . Select:
!CAR I function
button
> Car systems* control button > Driver
assist
> Rain sensor. In intermittent mode,
you can adjust the interval time using the@
switch.
@ -Slow wiping
® -Fast wiping
©-Single wipe
® -Clean the windshield. To eliminate water
droplets, the windshield wiper performs one
afterwipe operation after several seconds
while driving . You can switch this function off
by moving the lever to position ® within 10
seconds of the afterwipe operation. The after
wipe function is reactivated the next time the
ignition is switched on.
...
-Never use the cupholder or adapter as an
ashtray- risk of f ire.
(D Note
Only dr ink containe rs with lids should be
carried in the cupholder. Liquid could spill
out and damage your vehicle's e lectronic
equipment or sta in the upholstery, etc.
Glove compartment
The glove comportment is illuminated and
con be locked.
Fig. 78 Glove compartment
.. To open the glove compartment, pull the
handle in the direct ion of the arrow
r:::;, fig. 78
and swing the cover down to open.
.. To close the glove compartment, push the
glove compartment lid upward unt il the lock
engages.
The glove compartment can be locked using
the mechanical key
r:::;, page 33.
On the r ight side in the glove compartment is
a holder with the key body into which the
emergency key must be clipped to be able to
start the vehicle.
A WARNING
To reduce the risk of persona l injury in an
accident or sudden stop, always keep the
glove compartment closed whi le driving.
S ea ts a nd s to rage 67
Luggage compartment
General information
A WARNING ~
Read and follow the important safety pre-
cautions on
r:::;, page 124, Stowing lug
gage.
Enlarg ing th e luggage compartm ent
The backrests con be folded forward either
separately or together.
Fig. 79 Luggage compartment: release lever
Folding the b ackre st forward
.. Pull the release lever in the direction of the
arrow to fold the backrest forward .
Fo ldi ng t he back res t b ack into th e upr ight
po sition
.. Fold the backrest back up again until it
latches securely
r:::;, _& .
A WARNING
The backrest must be securely latched so
objects cannot slide forward out of the
luggage compartment during sudden
braking.
0 Note
When folding the backrest forwa rd, make
sure the rear safety be lts a re in the belt
guides so they do not become pinched in
the backrest lock and damaged. Othe r ob
jects shou ld be removed from the rear
bench seat to protect the backrest from
damage.
68 Seats and storage
Tie-downs
The luggage compartment is equipped with
four tie-down rings to secure luggage and
other items.
Fi g. 80 Luggage compartment: tie-downs
.. Secure objects us ing e lastic cords attached
to the tie-downs¢
fig. 80 .
.. Observe the safety notes¢ page 125.
Securing the ski sack
Applies to vehicles: with ski sack
Long objects such as skis or snowboards can
be transported in the ski sack.
Fig. 8 1 Luggage compartment : Securi ng the ski sack
Fig. 82 Rear benc h seat : secu ring the sk i sack
.. Fold both backrests forward ¢ page 67. ..
Slide the ski sack from the luggage com ·
partment through the opening ¢
A with
the zipper at the rear.
.. To secure the ski sack in the luggage com
partment, hang the hooks ®¢
fig. 81 in
the rear tie-downs .
.. Tighten the strap@¢
fig. 82 on the ski
sack to prevent the objects in the sack from
sliding.
_& WARNING -
- The s ki sack is in tended only fo r the
transportat ion of sk is and other light ob
jects . To reduce the risk of serio us per
sonal injury, never transport heavy or
pointed objects in the ski sack .
- When braking rapid ly or during an acci
dent, the load could be displaced and
cause injury to occupants.
- Sharp edges on the load must be covered
for protection. A lways fasten the belt
tightly around the sack and its contents
¢fig. 82.
-For safety reasons, do not transport
more than two pairs of skis in the ski
sack.
- You must secure the ski sack with the
strap after load ing.
- Make sure that all objects you are trans
port ing with the backrests folded for
ward are secured. They could slide
around d uring sudden b rak ing maneu
vers and cause injuri es.
(i) Tips
- Never stow the ski sack away when it is
st ill wet or damp (for example, snow
melting from skis). Allow it to dry com
pl etely before stow ing it away.
- When transporting sk is or snowboards,
t ighten the securing strap between th e
bind ings.
- Pos ition skis i n the sk i sack with the
pointed ends facing the front and ski
poles with the pointed e nds facing the
rear.
switching recirculation mode on when driving
through a tunnel or when sitting in traffic
c::>_& .
The IAU TOI button or I@ F RONT I button
switches recircu lation mode off .
IAUTO I Switching automatic mode on
Automatic mode mainta ins a constant tem
peratu re in side the vehi cle. Air temperature,
airflow and air distribution are controlled au
tomatically.
Adjusting the temperature
Temperatures between 60 °F (+16 °C) and
84
°F (+ 28 °C) can be set . Outside of this
range,
LO or HI will appear in the climate con
trol system display. At both of these settings,
the climate control system runs continuously
at maximum cooling or heating power. There
is no temperature regu lation.
~ Adjusting the airflow
You can adjust the airflow manually to suit
your needs . To have the airflow regulated au
tomatically, press the IAUTO ! button.
~Adjusting the air distribution
You can manually select the vents where the
a ir will flow. To have the air d istr ibution regu
lat ed automatically, press the
IAUTOI button.
~ Adjusting seat heating*
Pressing the button switches the seat heating
on at the highest sett ing (level 3). The LEDs
indicate the temperature leve l. To reduce the
temperature, press the button again. To
switch the seat heating off , press the button
repeatedly until the LE D turns off.
After 10 minutes, the seat heating automati
cally switches from level 3 to level 2.
[ill Adjusting seat ventilation*
Pressing the button switches the seat ventila
tion on at the highest setting (level 3) . The
LE Ds ind icate the ventilat ion level. To reduce
the ventilation leve l, press the button aga in.
To switch the seat ventilat ion off, press the
button repeatedly until the LED turns off.
Warm and cold 71
l F RON T I Switch the defroster on/off
The w indshield and side windows are defrost
ed or cleared of condensation as quickly as
possible . The maximum amount of air flows
main ly from the vents below the windshield.
Recirc ulation mode switches off. The tempera
ture should be set to 72
°F (22 °() or higher.
The temperature is controlled automatically.
The
! AUTO I button switches the defroster off.
lliil R EAR ! Switching rear window heater
on/off
The rear window heater on ly operates when
the engine is running .
It switches off auto
matically after a few minutes, depending on
the outside temperature.
To prevent the rear window heater from
switching off automatically, press and hold
the
l oo REARI button for more than 2 seconds.
This remains stored until the ign ition is
switched off .
Air vents
You can open and close the center and rear air
vents using the thumbwheels . The levers ad
just the direction of the airflow from the
vents.
In vehicles with a 3-zone deluxe automatic cli
mate control system*, you can adjust the air
temperature in the rear by turn ing the thumb
whee l toward the red side to make it warmer
or toward the b lue side to make it cooler .
A WARNING
-Do not use the recirculation for extended
periods of time. The windows could fog
up since no fresh air can enter the vehi
cle. If the windows fog up, press the air
recircu lation button again immediately
to switch off the air recirc ulation func
tion or se lect defrost.
- Individuals with reduced sensitivity to
pain or temperature could develop burns
when using the seat heating function. To
reduce the risk of injury, these indiv idu
als should not use seat heating.
A WARNING ,~
- Always pay attention to the traffic
around you whe n the cruise contr ol is in
o peration . You are always responsi ble for
your s peed and the distance between
yo ur vehicle and other vehicles.
- For reasons of safety, cruise contro l
should not be used in the city, in stop
and-go traff ic, on twisting roads and
when road conditions are poor (su ch as
ice, fog, grave l, heavy rain and hydro
planing) -risk of accident.
- T urn off the cru ise control tempo rar ily
when entering turn lanes, highway exit
lanes or in construction zones.
- Please note that inadvertent ly "rest ing"
yo ur foot on the accelerator peda l causes
the cruise control not to brake. Th is is
because the cr uise control is overridden
by the driver's acce lerat ion.
- If a brake system malfunction such as
overheat ing occurs when the cruise con
tro l system is sw itched on, the braking
function in the system may be switched
off. The other cruise control f unctions re
main active as long as the i nd icator light
lij jUJ~i4 (US models) lli,'I (Canad ian mod
els) is on.
(D Tips
The brake lights illuminate as soon as the
bra kes apply automat ica lly.
Changing speed
.,. To increase/dec rea se the speed in incre
ments, tap the lever in the
0 10 d irection
~ page 82, fig. 94.
.,. To increase/dec rease the speed quickly, hold
the lever in the
0 10 direction unti l the de
s ired speed is displayed.
You can also press the accelerato r peda l down
to increase your speed, e .g. if yo u want to
pass someone. The speed yo u saved earlier
will resume as soon as you let off of the accel
erator pedal.
On th e ro ad 83
If, however, you exceed yo ur saved speed by
6 mph (10 km/h) for longer than 5 minutes,
the cr uise contro l wi ll be t urned off tempora
rily. The green symbol in the disp lay t urns
white. The saved speed remains the same.
Presetting your speed
You can preset your desired speed while the
vehicle is not moving.
.,. Switch on the ignition.
.,. Pull lever into position
(D ¢ page 82,
fig . 94.
.,. Press the lever in the 0 or O direction to
increase or decrease your speed .
.,. Release the lever to save that speed .
This function makes it possib le, for examp le,
to save the speed you want before dr iving on
the highway. Once on the highway, act ivate
the cr uise control by pulling the leve r toward
(D .
Switching off
Temporary deactivat ion
.,. Press the b rake pedal, or
.,. Press the lever in to posi tion @(n ot clicked
into place)
¢ page 82, fig . 94, or
.,. Drive fo r longer than 5 min utes at more
than 6 mph (10 km/h) above the stored
speed.
Switching off completely
.,. Press lever into position @(clicked into
place), or
.,. Switch the ignit ion off .
T he speed you saved will be retai ned if the
c ruise control has been swi tched off tempora
rily. To resume the saved speed, let up on the
brake and p ull the lever to position
(D .
Swi tc hi ng the igni tion off e rases the saved
speed.
gear. Drive to your authorized Audi dealer or
qualified repair facility immediate ly to have
the ma lfunction corrected.
[O] Transmi ssion m alfu nction: Sto p ve hicle
a nd shift t o park .
Do not continue driving. Select the P selector
lever position and see your authorized Audi
dealer or qualified repair facility for assis
tance.
(D Note
If the transmiss ion sw itches to emergency
mode, you shou ld take the vehicle to an
authorized Audi dealership as soon as pos
sible to have the condition corrected.
Selector lever emergency release
If the vehicle's power supply fails, the s elec
tor lever can be released in an emergency.
Fig. 101 Front center console: Removing the ash tray
i nser t
Fig. 102 Selector lever emergency release
.. To access the emergency release mecha
nism, remove the ashtray insert @ using the
release switch @r:!>
fig. 101 .
.. Loosen and remove the cap in the ashtray
mount.
T ra n sm iss io n 9 1
.. You now have access to a pin. Using a screw
driver or simi lar object, press the pin down
and hold it in that position
<=>fig. 102.
.. Now press the release button and move the
selector lever to the N position.
The selector lever can only be moved from the
P position if the key is in the lock and the igni
tion is switched on. If the power supply fails
(for example , the battery is discharged) and
the vehicle must be pushed or towed, move
the selector lever to the
N position first using
the emergency release.
92 Audi adaptive cruise control and braking guard
Audi adaptive cruise
control and braking
guard
Introduction
App lies to vehicles: with Audi adaptive cruise co ntrol
The adaptive cruise control system assists the
driver by regulating vehicle speed and helping
to maintain a set distance to the vehicle
ahead, within the limits of the system .
If the
system detects a moving vehicle up ahead,
adaptive cruise control can brake and then ac
celerate your vehicle. This he lps to make driv
ing more comfortable on long highway
stretches.
The braking guard system can warn you about
an impending collision and initiate braking
maneuvers
c:::> page 98.
Adaptive cruise control and braking guard
have technical limitations that you must
know, so please read this section carefully, un
derstand how the system works and use them
properly at all times.
General information
General information
Applies to vehicles: with Audi adaptive cruise co ntrol
Fig. 103 Front of the vehicle: Position of radar senso r
The area that contains the radar sensor
c:::> fig. 103 must never be cove red by stickers
or other objects or obstructed with dirt, in
sects, snow or i ce that will interfere with the
adaptive cruise control system and braking
guard. For information on cleaning, refer to
c:::> page 193. The same applies for any modifi
cations made in the front area . T
he function of the adaptive cruise cont rol
system and braking guard is limited under
some condit ions:
- Objects can only be detected when they are
within sensor range
c:::>page 94, fig . 106.
-The system has a limited ability to detect
objects that are a short d istance ahead, off
to the side of your vehicle or moving into
your lane.
- Some kinds of vehicles are hard to detect;
for examp le motorcycles, vehicles with high
ground clearance or overhanging loads may
be detected when it is too late or they may
not be detected at all.
- When driving through curves
c:::> page 93.
- Stat ionary objects c:::> page 93 .
A WARNING
-
Always pay attention to traffic when adap-
tive cruise contro l is switched on and brak
ing guard is active. As the driver, you are
still respons ible for starting and for main
tain ing speed and distance to other ob
jects. Braking guard is used to assist you.
The driver must always take action to avoid
a col lision. The driver is always responsible
for braking at the correct time.
- Im proper use of adaptive cruise con trol
can cause collisions, other accidents and
serio us personal injury.
- Never let the comfor t and convenience
that adaptive cruise control and braking
guard offer distract you from the need to
be alert to traffic conditions and the
need to remain in full control of your ve
h icle at a ll times,
- Always remember that the adaptive
cru ise contro l and brak ing guard have
lim its -they will not s low the vehicle
down or maintain the set distance when
you drive towards an obstacle or some
thing on or near the road that is not
mov ing, such as vehicles stopped in a
traffic jam, a stalled or disabled vehicle.
If registered by the radar sensor, vehicles
or obsta cles that are not moving can
trigger a co llision warning and if
94 Audi adaptive cruise control and braking guard
Audi adaptive cruise
control
Description
Applies to vehicles: with Audi adap tive cruise co ntrol
Fig. 106 Detection range
What can Audi adaptive cruise control do?
The adaptive cruise control works in conjunc
tion with a radar sensor installed in the front
of the vehicle¢
page 92, fig. 103, which is
subject to designated system limits
¢
page 94. Stationary objects are disregard
ed .
On open roads w ith no traffic, adaptive cruise
control works like a regular c ruise control sys
tem. The stored speed is maintained. When
approaching a moving vehicle detected up
ahead, the adaptive cruise control system au
tomatically slows down to match that vehi
cle's speed and then maintains the distance
that the driver previously stored. As soon as
the system does not detect a vehicle up
ahead, adaptive cruise control accelerates back up to the stored speed.
Which functions can be controlled?
When you switch adaptive cruise contro l on,
you can set the current speed as the "control
speed"
¢ page 94, Switching on and off.
When driving, you can stop cruise control
¢
page 96 or change the speed ¢ page 95
at any time.
You can also set the distance to the object
ahead and set the adaptive cruise control driv ing program
¢page 96.
Switching on and off
Applies to vehicles: with A udi adapt ive cruise contro l
Fig. 107 Selecto r lever: sw itching on/off
Fig. 108 Instrument cluster: Audi adaptive cruise con
trol
You can set any speed between 20 mph and
95 mph (30 and 150 km/h).
Indicator lamps and messages in the instru
ment cluster disp lay inform you about the cur
rent system status and settings.
Switching Audi adaptive cruise control on
.,. Pull the lever towa rd you into position@
¢
fig. 107. ACC standby appears in the in
strument cluster display.
Setting the speed and activating
regulation
.,. To set the current speed, press the ISETI but-
ton¢
page 11, fig. 4. The set speed is .,..