Convertible child safety seats
Properly used convertible child safety seats
can help protect toddlers and children over
age one who weigh between 20 and 40 lbs . (9
and 18 kg) in a crash.
F ig . 162 Schematic overview: installat ion of the at
tachments appl icable to a LA TCH seat
.r
F ig. 163 Schem atic overview: installat ion of t he seat
using the vehicle 's s afety b elt system
.. When using the vehicle safety be lt to insta ll
a chi ld safety seat, you must f irst activate
the convertible locking feature on the safety
belt to prevent the child safety seat from
moving
c::> page 168 or install the seat using
the LATCH attachments.
.,. Push the child safety seat down with your
full weight to get the safety belt really t ight
so that the seat cannot
move forward or
s ideways more than one inch (2.5 cm)
c:;, page 168.
.,. Secure un used safety belts on the rear sea t
c:;, page 163.
A toddler or child is usually too large for an in
fant restraint if it is more than one year o ld
and weighs more than 20 lbs . (9 kg) .
Toddlers and ch ildren who are older than one
year up to about 4 years o ld and weigh more
than 20 lbs . (9 kg) up to 40 lbs. (18 kg) must
Child S afety 165
always be properly restrained in a child safety
seat certified for their size and weight
¢fig.162 and c::> fig .163 .
The airbag on the passenger side makes the
front seat a potentia lly dangerous place for a
child to ride. The front seat is not the safest
place for a child in a forward -facing child safe
ty seat. It is a very dangerous p lace for an in
fant or a larger ch ild in a rearward-facing seat.
A WARNING
Not using a child safety seat, using the
wrong child safety seat or imprope rly in
stalling a ch ild restraint increases the risk
of ser ious personal inju ry and death in a
coll is ion or other emergency sit uat ion.
- Ch ildren o n the front seat of any ca r,
even with Advanced Airbags, can be se ri
ously i njured or
even k ill ed when an air
bag inflates . A child in a rearward -facing
child safety seat installed o n the front
passenger seat will be serious ly injured
and can be k illed if the front airbag in
flates -
even with an Advanced Airbag
System .
-
-The inflating airbag will hit the ch ild
safety seat or infant carrier with great
force and will smash the child safety seat
and child agai nst the backrest, center
armrest, doo r or roof .
- Always install rea rward -facing chi ld safe
ty seats on the rear seat.
- If you must install a rearward fac ing
child safety seat on t he front passenge r
seat because of exceptional c ircumstan
ce s and t he
PASSENGER AIR BAG OFF
light does no t come o n and stay on, im
mediately insta ll the rearward-facing
child safety seat in a rear seating posi
tion and have the airbag system inspect
ed by your authorized A udi dealer .
- The rear side of the child safety seat
should be pos itioned as close as poss ib le
to the backrest on the vehicle seat.
- Always read and heed all WARNINGS
whenever using a child restrained in ave-
hicle is being used
c:;, page 129, Safety 11>
168 Child Saf ety
- If the PASS ENGER AIR BAG O FF li ght
does not come on and stay on, perform
the checks described
c:> page 148, Moni
toring the Advanced Airbag System .
-Take the child restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PASSEN
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Always read and heed all WARNINGS whenever using a child rest rained in ave
hicle is being used
c:> page 129, Safety
belts, c:>page
137, Airbag sy st em and
<:?v page 158, Important things to know.
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the rear seats and the front
pas senger 's seat can be locked with the con
vertible locking retractor to properly secure
child safety seats.
The safe ty belts eme rgency lock ing re tractors
fo r the re ar seats safe ty belts and for the
fro nt passenger's seat safety belt have a con
vertible locking retracto r fo r child restraints.
The safety belt must be locked so that belt
webbing cannot unree l. The retractor can be
activated to lock the safety be lt and prevent
the safety belt webbing from loosening up
during normal driving . A child safety seat can
only be properly installed when the safety belt
i s locked so that the child and child safety
seat will stay in place.
A lways remember: Even thoug h your veh icle is
eq uipped w it h an Advanced A irbag system, all
ch ildren , espec ia lly those 12 yea rs and yo ung
e r, should always ride in the ba ck seat proper
l y res traine d for thei r age and weig ht.
_& WARNING
Imprope rly insta lled child sa fe ty seats in
crease the risk of ser ious personal inju ry
and death in a collision. -
Always make sure that the safety belt re
tractor is locked when insta lling a child
safety seat. An unlocked safety belt re
tractor cannot hold the child safety seat in place dur ing no rma l dr iving o r in a
crash .
- Always buckle the child safety seat firmly in place even if a ch ild is not sitt ing in it .
A loose child safety seat can fly aroun d
du ring a s udden st op or in a colli sion.
- I f the backrest is not securely la tched,
the child and the child restraint will be
throw n forward toge ther with t he ba ck
rest and will strike par ts of the vehicle
interior. The child can be se riously in
jured or killed.
- Never inst all rearward-facing child safety
seats or infant ca rr iers on the front pas
senger seat . A child will be serious ly in
jured and can be killed when the passen
ger airbag i nflates.
- The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smash the child safety seat
and child aga inst the back rest , center
armrest, doo r or roof.
- Always install rearward-facing ch ild safe
ty seats or infa nt carriers on the rea r
seat .
- Forwa rd-facing child safety seats or in
fant car riers installed on the front pas
senger's seat may interfere with t he de
p loyment of t he a irbag and cause serious
i njur y to the child .
-It is safer to ins tall a forward-facing
child safety seat on the rear seat.
- Always read and heed all WAR NIN GS
whe neve r using a child restrai ned in ave
h icle i s being u sed
c:> page 158. Special
p reca utions apply when ins tal ling a child
safety seat on the fron t passenger seat
c:> page 138, Child restraints on the front
seat -some important things to know.
_& WARNING
--
Always take specia l precautions if you
must install a forwa rd or rearward-facing
child restraint on the front passenger's
seat in exceptional situations:
- Whenever a forward or rearward-facing
child restraint is installed on the front
passenger seat, the
PASSENGER AIR
BAG OFF
light must come on and stay on
whenever the ignition is switched on .
-If the PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described
~ page 148, Moni
toring the Advanced Airbag System .
- Take the child restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PASSEN·
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Improper installation of child restraints
can reduce their effectiveness or even
prevent them from providing any protec
tion.
- An improperly installed child restraint
can interfere with the airbag as it de
ploys and seriously injure or even kill the
<;hild.
- Always carefully follow the manufactur
er's instructions provided with the child
safety seat or carrier.
- Never place additional items on the seat
that can increase the total weight regis
tered by the weight-sensing mat and can cause injury in a crash.
_&. WARNING
Forward-facing child restraints:
- Always make sure the forward-facing
seat has been designed and certified by
its manufacturer for use on a front seat
with a passenger front and side airbag.
- Never put the forward-facing child re·
straint up, against or very near the in
strument panel.
- Always move the passenger seat into its
rearmost position in the seat's fore and
aft adjustment range, as far away from
the airbag as possible before installing
the forward-facing child restraint. The
Child Safety 169
backrest must be adjusted to an upright
position.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on .
_&. WARNING
"' Rearward-facing child restraints:
-A child in a rearward-facing child safety
seat installed on the front passenger
seat will be seriously injured and can be
killed if the front airbag inflates - even
with an Advanced Airbag System .
- The inflating airbag will hit the child
safety seat or infant carrier with great
force and will smash the child safety seat
and child against the backrest, center
armrest, door or roof.
-Always be especially careful if you must
install a rearward facing child safety seat
on the front passenger seat in exception
al circumstances.
-A tight tether strap on a rearward-facing
child restraint attached to the front pas
senger seat can put too much pressure
on the weight-mat in the seat and regis
ter a heavier weight in the Advanced Air bag System. The heavier weight regis
tered can make the system work as
though an adult were on the seat and de
ploy the Advanced Airbag when it must
be suppressed causing serious or even
fatal injury to the child.
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
- If the PASSENGER AIR BAG OFF light
does not come on and stay on, immedi
ately install the rearward-facing child
safety seat in a rear seating position and
have the airbag system inspected by your
authorized Audi dealer. •
•
A WARNING ,~
After driving through water, mud, slush,
etc., the brakes may be slow to take effect
because of wet brake rotors and pads. Dry
the brakes first by braking carefully to re
store the full brak ing effect.
([) Note
Vehicle components such as the engine,
transmiss ion, suspension or electrical sys
tem can be severely damaged by driving
through wate r.
@ Tips
- Check the depth of the water before dr iv
i ng through it.
- Do not stop the veh icle, dr ive in reverse
or switch the engine off when driving
th rough water.
- Keep in mind that oncoming vehicles may create waves that raise the water
level and make it too deep for you r vehi
cle to drive through safely.
- Avoid dr iving through salt water because
i t can cause corrosion.
Warming up and
cooling down
By carefully warming up and cooling down
your vehicle, you can he lp ensure that it is not
overstressed unnecessarily during sporty driv ing.
When warming up, the vehicle is driven at a maximum engine speed of 6000 RPM in order
to raise the engine oil temperature to a mini mum of 140 °F (60 °C) . The tires also only
reach their full road holding capability once
they have warmed up .
The cooling fan can continue to run in your ve h icle after the engine is switched off. Howev
er, driving the vehicle to cool it down is part ic
ularly important . Du ring sporty driving, the
engine and brakes, the exha ust system, and
the transm ission all become ext remely hot.
Before you park the vehicle, you shou ld drive
Dri vin g and en vironm ent 185
it for a few miles/kilometers at light load in
the low rpm range to allow it to cool down.
Catalytic converter
It is very important that your emission con
trol system (catalytic converter) is function
ing properly to ensure that your vehicle is run
ning in on environmentally sound manner.
"" Always use lead-free gasoline c> page 202,
Fuel supply.
"" Never run the tank down all the way to emp
ty.
"" Never put too much motor o il in your engine
<=> page 212, ~ Adding engine oil .
""Never try to push- or tow-sta rt you r vehicle.
The catalyt ic converter is an efficient "clean
up" device bui lt into the exhaust system of
the ve hicl e. The cata lytic conve rter bu rns
many of t he pollutants in the exha ust gas be
fo re t hey are re leased into the atmosphere.
The exclusive use of unleaded fue l is critically
important for the life of the catalyt ic convert
er and proper funct ion ing of the engine.
A WARNING ~
- The temperature of the exhaust system
is high, both when driving and after stop
ping the engine.
- Never touch the exhaust tail pipes once they have become hot . This could result
in burns .
- Do not park or operate the vehicle in areas where the hot exha ust system may
come in contact with dry grass, brush,
fuel spill or other material wh ich can
cause a fire.
- Do not apply additional undercoating or rustproof ing on or near the exhaust
manifold, exhaust pipes, catalytic con
verter or heat shields . Dur ing driving, the
substanc e used fo r undercoating could
overheat and cause a fire. •
•
190 Cleaning and protection
Automatic car wash
Th e ve hicl e can be washed in almost any
modern automatic car wash .
The vehicle paint is so du rable that t he ve hicle
can normally be washed without problems in
an automatic car wash . However, the effect on
the paint depends to a large extent on the de
sig n of the facility, the filte ring of the wash
wate r, the type of wash and care mater ia l, etc.
If th e p aint ha s a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi
ately.
If necessary, use a different car wash.
Th e power top does no t require special pre
cautions be fore passing through a car wash.
However , the car mu st not be treated with
hot wa x after the wash cycle!
The wax could
adversely affect the power top and even dam
age the fabric ove r a period of time.
The power top does not have to be washed ev
e ry time you use a car wash . The power top
can be spared if the car wash facility is equ ip
ped with manually adjustable roof brushes or
rollers.
Before going through a car wash, be sure to
take the usual precaut ions such as clos ing the
windows . Remove antenna if applicable.
I f yo u have installed additional accessories on
the vehicle - such as spoilers, etc. - it is best to
ask the car wash operator i f these should be
removed.
On ly use car washes where the vehi cle re
mains stationary and the cleaning equipment
moves around the vehicle wh ile washing and
drying. It is not recommended to use car
washes where the vehicle is moved forward on
a conveyer.
A WARNING
- Always read and heed all WAR NIN GS and
ot he r i nforma tio n
¢ page 189.
(D Note
- Before wash ing the ve hicle in an auto
matic ca r wash, please make su re to re
tract the exter ior mir rors to prevent
them from be ing damaged .
- Compare the w idth of yo ur vehicle with
the width of the tunne l at the facility.
- Compa re the track of yo ur vehicle with
the distance between the g uide rails of
the facility -there is a risk of damage to
the whee ls and tires.
Washing the vehicle by hand
A lot of water is needed when washing a vehi
cle by hand.
.,. Before yo u start washing, ma ke s ure you
have read a nd understood the WARNINGS
¢ .&, .
.,. First soak all dried d irt unt il it is soft, then
r inse it off .
.,. As you clean yo ur vehicle, start w ith t he roof
and wo rk your way down to t he bo ttom, us
ing a sponge, a s ponge g love or a clean
br ush .
.,. Rinse the s ponge o r th e sponge g love o ften,
flushi ng it clean eac h time .
.,. Use spec ia l car shampoo only for very persis
tent dirt .
.,. Rinse the car t ho roughly with water.
.,. Use a chamo is leather to gently wipe the ex-
t er ior d ry .
U se a separate sponge for cleaning the
whee ls, door s ills and othe r regions exposed
to road dirt . In this way, yo u w ill not scratch
t h e pa int w ith coarse pa rticles imb edded in
t h e sponge the next time you wash t he ca r.
A WARNING
- W ash your vehicl e only when the ign ition
is swi tched o ff to re duce the r isk o f a
crash .
- Always re ad and heed a ll WA RNIN GS and
o ther in fo rm ation
¢ page 1 89 .
Windows
Clear vision to all sides.
Clean all windows regularly to remove road
film and car wash wax buildup.
• Remove snow from windows using a brush.
• Use a plastic ice scraper to remove ice from
windows and mirrors.
• Remove other residue on the windows with
a spray-on glass cleaner .
• Wipe the windows dry w ith a clean p iece of
cloth or kitchen paper towel.
The best way to remove snow from windows
and mirrors is to use a brush. Use a non -abra
sive
p la stic ic e scrap er -better still, a spray
de icer - to remove
ic e from windows and mir
r ors.
T he windows must not be cleaned with insect
remover or wax s ince these can interfere with
the function of the w indshield wiper blades
(chatter).
O il, grease, or silicone residue can be removed
w ith
glass cleaner or silicon e re mover. H ow
ever, wax residue requ ires the use of a special
l y form ulated solvent. P lease contact your au
thor ized Audi dealer for adv ice on safe prod
ucts for wax removal.
W indows shou ld a lso be cleaned on the inside
at regular i nterva ls.
Never dry w indows with the same chamois
that you use to dry painted surfaces . Wax resi
due on the chamois can impair vision through
the windows.
.8, WARNING
- Alw ays re ad and heed all WARN INGS and
other information
~ page 189.
- The windshie ld m ust not be treated with
water-repe llent m aterials. They can i n
crease glare under poor visib ility condi
tions such as wetness, darkness, or whe n
the sun is low on the horizon . In addi
t ion, they can cause the windshield wip
ers to chatter.
Cleaning and protec tion
@ Note
- Never use warm or hot water to remove
snow and ice from w indows and mirrors .
Th is could cause the glass to crack.
- To prevent damage to the wires of the
rear defogger, do not place any adhesive
st ickers on the ins ide of the rear w indow
over the wires.
- To help prevent dirt from scratching the window, always scrape in a forward di
rection - pushing the scraper away from
you - never back and forth.
- Water leak ing from the inside of the rear
w indows may damage sens itive electrical
compone nts located either under the
rear parcel shelf or in the rear trunk area.
Always ensure tha t water never lea ks
t hro ugh the body section of the vehicle.
Yo u can do th is by using waterproof pro
tection over the vehicle's electrical com
ponents (e.g . when install ing window
tinting) .
- Damage or malfunction of electrical
components due to water damage or any
other o utside infl uence is not covered by
the Audi New Veh icle Limited Warranty.
See your Warranty
& Maintenance book
let for addit ional details about your war
ranty.
Cast (light) alloy wheels
Cast (light) alloy wheels require special care .
• Wash the wheels with a sponge or hose
brush every other week.
• For deep clean ing afterwards, use on ly a
ded icated
acid-fr ee cast alloy wheel cleaner .
• Rub a coat of
liquid wa x onto the rims every
three month. Be su re to reach and treat all
pa rts of the rim.
To preserve the decorative appearance of the cast alloy wheels, some special care is neces
sary. In addi tion to road dirt and salt, brake
dust is also co rrosive . If left on fo r too long,
brake dust can cause pitting.
IJI>
195
•
•
196 Cleaning and protection
Use only special acid -free cleaners form ulated
for a lloy rims. Safe products are available at
your author ized Audi dealer . Never leave the
cleaner on the rims longer than specified on
the label.
If no t rinsed off promptly, the acid
contained in some cleaners can attack the
threads on the wheel bolts .
Never use abras ive or metal polishing clean
ing agents. If the protective coating has been
chipped, e .g . by k icked up road dirt, touch it
up as soon as poss ible.
A WARNING
- Moist ure and ice on brakes may affect
braking efficiency ~
page 178. Test the
br ake s ca refully each time you wash the
vehicle.
- Always read and heed all WARNI NGS and
other informa tion ~
page 189.
Body cavity sealing
-
The body cavity sealing does not need to be
checked.
A ll body cavities wh ich could be affected by
corrosion have been thoroughly protected at
the facto ry.
T his sea ling does not require any inspection or
addit io nal treatment. If any wax should seep
out of the cav ity when the ambient tempera
ture is high, it can be removed w it h a plastic
scrape r and a su itab le so lven t.
A WARNING
So lvents can be dange rous.
- B enzine is flammable and t oxic.
If you
use benzine for removing the w ax, keep
spar ks, flame and lighted cigaret tes
away. Never dump benzine on t he
ground, into open streams or down sew
age drains.
- Be sure to observe all safety and env iron
menta l regulations . Follow all instruc
t ions on the container.
- Always read and heed all WAR NIN GS and
other information
¢ page 189. Chassis
Have the undercoating checked for damage
from time to time.
The lower body shell of your Aud i is also thor
oughly protected against cor ros io n.
Any damage to the unde rcoating ca used by
road ha zards should be repaired prompt ly.
A WARNING ....__
Too much undercoating in the wrong p la
ces can cause a fire.
- Do not app ly additional undercoating or
r u stp roof ing on or near the exhaust
manifold, exhaust pipes, catalytic con
ver ter or heat shields. While driving, the
substance used fo r undercoating could
overhea t and cause a fire.
- Always read and heed all WAR NINGS and
o ther info rmation ¢
page 189.
Exhaust tail pipes
Road salt and o ther co rrosive materials w ill
damage the mate ria l in the e xhaus t ta il pipes
i f they are not cleaned regular ly . Do not clean
the tail pipes with w hee l cleaner, pa int polish,
c h rome polish or other ab rasive cleane rs .
Clean the tail pipes with car care products
t h at are suitable for sta inless steel.
Your a uthorized Audi dea ler can prov ide clean
ing products that have been tested and ap
proved for your vehicle .
Care of interior
Infotainment components
The Rad io/MM !* disp lay may be cleaned w ith
a soft cloth and comme rcially-ava ilable "LCD
cl eaner". The clot h should be coated lightly
whe n the cleaning solution w hen clea ning t he
display.
T he M MI* con trols m ust be clean ed first wi th
a b rush so tha t dirt does not en ter the uni t or
enter between the buttons an d the housing.
The n wiping the controls with a cloth ..,.
temperatures stay below freezing point for l ong periods.
Detergent add itives in the o il w il l make fresh
oil look dark after the eng ine has been run
ning fo r a short time . This is norma l and is not
a reason to change the oi l more often than
recommended.
D am ag e or m alfun ction s due to lack of
ma intenanc e
It is essential that you change your oil at the
r ecommended inte rva ls using only engine o il
t hat complies with A udi oi l standard
VW 502 00 . Your Limited New Vehicle War
ranty does not cover damage or malfunctions
due to fa ilure to fo llow recommended mainte
nance and use requ irements as set forth in
the Audi Owner's Manual and Warranty
&
Maintenance book let . Your dealer will have to
deny warranty coverage u nless you present to
the dea ler p roof in the fo rm of Serv ice or Re
pa ir Orde rs that all s chedu led maintenance
was pe rformed in a t imely manner .
Engine oil consumption
The engine in your vehicle depends on an ade
quate amount of oil to lubricate and cool all
of its moving parts.
In o rder to provide effective lubrication and
cool ing of internal engine components, a ll in
ternal combustion eng ines consume a certa in
amo unt of o il. Oil consumption varies from
engine to engine and may change significantly
over the life of the engine. Typ ica lly, engines
with a specified break-in period (see
¢
page 184) consume more oil during the
break-in per iod than they consume after oil
consumption has stabilized .
Under normal conditions, the rate of oil con
sumpt ion depends on the quality and viscosity
of the oil, the RPM (revo lutions per m inute) at
which the engine is operated, the ambient
temperature and road condit ions. Furthe r fac
tors are the amount of o il d ilution from wate r
condensation or fuel residue and the ox ida
tion level of the oil. As any engine is s ubje ct to
Checkin g and fillin g 211
wear as mi leage builds up, the oil consump
tion may increase over time until replacement
of worn components may become necessary.
Wi th a ll these variab les coming into p lay, no
standard rate of oil consumpt ion can be es
tablished or specified. There is no alternative
to regular and frequent check ing of the o il lev
el, see
Note .
If the yellow engine oil leve l warning symbo l
1\1 in the instrument cluster lights up , you
shou ld check the oil leve l as soon as possib le
¢
page 212. Top off the oil at your earliest
convenience
¢ page 212.
A WARNING
Before you check anythi ng i n the engine
compartment, always read a nd heed all
WARNINGS¢ .&.
in Working in the engine
c ompartment on page 207.
(D Note
Driving w ith an insufficient o il level is like
ly to cause severe damage to the engine .
(D Tips
- The oil pressure warning display. is
not an indi cator of the oil le vel. Do not
rely on it . Instead, check the oil level in
your engine at regu lar intervals, pref
erably ea ch time you r efuel, and alway s
before going on a long trip .
-If you have the impression you r engi ne
c ons umes ex cess ive amoun ts of o il, we
recommend that you consul t an a uthor
ized Aud i dea ler to have the cause of
your concern properly diagnosed. Keep in mind that the accurate measurement of
oil consumption requ ires great care and
may take some t ime. An authorized Aud i
dealer has instructions about how to
measu re oil consumption accurately.
-
•
•