2013 AUDI RS5 CABRIOLET flat tire

-Read the requir ed tire pressure from the tire
pressure label. The tire pressure label is lo­
cated on the driver's side B-pillar. The tire
pressure label lists the recommended cold
t ire inf lation pressures for the vehicle at its
maximum capacity weight and the tires that
were on your vehicle at the time it was man­
ufactured . For recommended tire pressures
for normal load conditions, please see chap­
ter ~
page 226.
- Turn the valve stem cap counter-clockwise
to remove it from the tire valve.
- Place the air pressure gauge on the valve .
- The tire pressures should only be checked
and adjusted when the tires are cold . The
slightly raised pressures of warm tires must
not be reduced.
- Adjust the tire pressure to the load you are
carry ing.
- Reinstall the valve stem cap on the valve .
When should I check the tire pressure?
The correct tire pressure is especially impor­
tant at high speeds. The pressure should
therefore be checked at least once a month
and always before starting a journey .
When should I adjust the tire pressures?
Adjust the tire pressure to the load you are
carry ing. After changing a wheel
or replacing
wheels you have to adjust the tire pressures
on all wheels. In addition, you must then initi­
alize the new tire pressures in the tire pres­
sure monitoring system*~
page 240.
A WARNING
Incorrect tire pressures and/or underinfla­
tion can lead sudden tire failure, loss of
control, collision, serious personal injury
or even death.
- When the
[9] warning symbol appears in
the instrument cluster, stop and inspect
the tires.
- Incorrect tire pressure and/or underinfla­
tion can cause increased tire wear and
can affect the handling of the vehicle and
stopping ability.
Tires and wheels 229
- Incorrect tire pressures and/or underin­
flation can also lead to sudden tire fail­
ure, including a blowout and sudden de­
flation, causing loss of vehicle control.
- The driver is responsib le for the correct
tire pressures for all tires on the vehicle.
The applicable pressure values are locat­
ed on a sticker on the driver's side B-pil­ lar.
- Only when all tires on the vehicle are fil­
led to the correct pressure, the tire pres­
sure monitoring system* can work cor­
rectly.
- The use of incorrect tire pressure values
can lead to accidents or other damage.
Therefore it is essential that the driver
observe the specified tire pressure values
for the tires and the correct pressures for
the function of the tire pressure monitor­ ing system*.
- Always inflate tires to the recommended
and correct tire pressure before driving
off.
- Driving with underinflated tires bend
more, letting them get too hot resulting
in tread separation, sudden tire failure
and loss of control.
- Excessive speed and/overloading can
cause heat build-up, sudden tire failure
and loss of control.
- If the tire pressure is too low or too high,
the t ires will wear prematurely and the
vehicle will not handle well.
- If the tire is not flat and you do not have
to change a wheel immediately , drive at
reduced speed to the nearest service sta­
tion to check the tire pressure and add
air as required.
(D Note
Driving without valve stem caps can cause
damage to the tire valves. To prevent this,
always make sure that factory installed
valve stem caps on all wheels are securely
mounted on the valve.
•
•

230 Tire s and wheel s
@ For the sa ke of the environment
Underinflated tires will a lso increase the
fue l consumption.
Tires and vehicle load limits
There are limits to the amount of load or
weight that any vehicle and any t ire can carry.
A vehicle that is overloaded w ill not handle
well and is more difficult to stop. Overload ing
can not only lead to loss of vehicle control, but can also damage important pa rts of the
vehicle and can lead to s udden tire failure, in­
cluding a blowout and sudden deflation that
can cause the vehicle to crash.
Your safety and that of your passenge rs a lso
depends on making s ure that load limi ts are
not exceeded . Vehicle load includes everybody
and everything in and on the vehicle. These
load limits are technica lly referred to as the
vehicle's
Gross Veh icle We ight R ating
("GVWR").
The "GVWR" includes the weight of the basic
vehicle, all factory installed accessories, a full
tank of f uel, oi l, coo lant and other fluids pl us
maximum load. The maximum load includes
the number of passengers that the vehicle is intended to carry ("seating capacity") with an
assumed weight of 150 lbs . (68 kg) for each
passenger at a des ignated seat ing pos ition
and the tota l we ight of any l uggage in the ve­
h icle. If you tow a trailer, the weight o f the
trai ler hitch and the tong ue weight of the
loaded trailer must be included as part of the
vehicle load.
The
Gro ss Axl e W eight Rating ("GAWR") is
the maximum load that can be app lied at each
of the vehicle's two axles.
The G ross Vehicle Weight Rating and the
Gross Axle Weigh t Rating are listed on the
safety compliance sticker labe l located on the
driver's side B-pi llar . Audi has 4 seati ng posi­
tions, 2 in the front and 2 in the rear for tota l
seating capacity of 4 . Each seating position
has a seat belt¢
page 129, Safety belts.
T he fact that there is an upper limit to yo ur
vehicle's G ross Vehicle Weight Rating means
that the total weight of whatever is being car­ ried in the vehicle ( includ ing the weight of a
trailer hitch and the tongue weight of the
loaded tra iler) is lim ited . The more passen­
gers in the vehicle or passengers who are
heavier than the standard we ights assumed
mea n tha t less we ight can be carried as lug­
gage.
T he t ire pressure label on your Aud i also lists
the max imum combined weig ht of a ll of the
occupants and luggage or other cargo that
the vehi cle can carry . For the location of the
label¢
page 226, fig. 185.
.&, WARNING ~ -
Overloading a vehicle can cause loss of ve ­
h icle contro l, a crash or other accident, se­
rious personal injury, and even death.
- Ca rrying more weight than your vehicle
was des igned to carry wi ll prevent the
vehicle from handling properly and in­
crease the risk of the loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ith in a safe distance.
- Tires on a vehicle that has been overload­
ed can fail suddenly, including a blowout
and sudden deflation, causing loss of
control and a crash .
- Always make sure that the total load be­
ing transported -including the weight of
a trailer hitch and the tongue we ight of a
loaded trailer - does not ma ke the vehi­
cle heavier than the vehicle's G ross Vehi­
cle Weight Rating.
Determining correct load limit
U se th e exa mple b elow to ca l­
c ulat e th e total w eight of the

passengers and luggage or oth­
er things that you plan to trans­ port so that you can make sure
that your vehicle will not be
overloaded.
Steps for Determining Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OC­
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS"on your vehi­
cle's placard (tire inflation pressure label)
¢ page 226,
f ig. 185.
2. Determine the combined
weight of the driver and pas­ sengers that will be riding in
your vehicle.
3. Subtract the combined weight of the driver and pas­sengers from
"XXX" kilo­
grams or
"XXX" pounds
shown on the sticker
¢ page 226, fig. 185 .
4. The resulting figure equals
the available amount of car­go and luggage load capaci­
ty. For example, if the
"XXX"
amount equals 1400 lbs.
and there will be five 150
lbs. passengers in your vehi­
cle, the amount of available
Tires and wheels 231
cargo and luggage load ca­
pacity is 650 lbs. (1400-7
so
(5 X 150) = 650 lbs.)
5. Determine the combined
weight of luggage and cargo being loaded on the vehicle .
That weight may not safely
exceed the available cargo
and luggage load capacity
calculated in Step
4 .
6 .
If your vehicle will be towing
a trailer, load from your trail­
er will be transferred to your
vehicle . Consult this manual
to determine how this re­ duces the available cargo
and luggage load capacity of
your vehicle .
~check the tire sidewall
(¢ page 233 , fig. 189) to de­
termine the designated load
rating for a specific tire.
•
•
'

A WARNING
Sudden tire failure can lead to loss of con­
trol, a crash and serious personal injury!
- Never drive a vehicle when the tread on
any tire is worn down to the wear indica­
tors.
- Worn tires are a safety hazard, they do
not grip well on wet roads and increase
your risk of "hydroplaning" and loss of
control.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from t ires.
- Tires age even if they are not be ing used
and can fail suddenly, especially at high
speeds . Tir es that are more than 6 years
old can only be used in an emergency
and then with special care and at lower
speeds.
- Never mount used tires on your vehicle if
you are not sure of their" previous histo ­
ry ." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden tire failure
and loss of vehicle control.
Tires and wheels 233
New tires and replacing tires and wheels
New tires and wheels have to be broken in .
Fig. 189 Tir e specificat ion codes on t he s idewall o f a
tire
No. Description
CD Passenger car tire (where applicable)
@ Nominal width of tire in millimeters
® Ratio of height to width (aspect ratio)
© Radial
® Rim diameter code
® Load index and speed rat ing
(f) U.S. DOT tire identification number
® Audi Original tire
® Sever snow conditions
@ Tire ply composition and materials
used
@ Maximum load rating
@ Treadwear, traction and temperature
grades
@ Maximum permissible inflation pres-
sure
The tires and rims are essential parts of the
vehicle's design . The ti res and rims approved
by Audi are spec ially matched to the charac­
teristics of the vehicle and can make a major .,.
•

234 Tire s and wheel s
contribution to good road ho lding and safe
handling when in good condition and properly
inflated
¢ ,& .
We recommend that all work on tires and
wheels be perfo rmed by an authorized Audi
dea ler. They are familiar with recommended
proced ures and have the necessary spec ial
too ls and spare parts as well as the proper fa­
cilities for disposing of the old tires.
Authorized Audi dealers have the necessary information about techn ica l requ irements for
installing or changing tires and r ims.
Re placing t ires and whe els
Tires sho uld be rep laced at least in pairs and
not individua lly (for examp le both front tires
or both rear tires together).
Be sure to read and heed the information to
the tire pressure monitoring system*
¢page 240.
A lways buy rep lacement radial tires that have
the same specifications as the tires approved
for your vehicle by Audi. Replacement t ires
must always have the same load rating speci­
fication as the original equipment or approved
optional tires listed in the table
c:> page 226.
Aud i-approved specification ti res are specially
matched to your vehicle and its load limits,
and can contribute to the important road ho ld­
ing, driving characteristics, and safety of the
vehicle. The table (c:>page 226) lists spec ifica­
tions of the tires approved for the Audi mod­
els covered by your Owner's Literature .
The tire pressure labe l located on driver's side
B-pillar (c:>page 226, fig. 186) lists the speci­
f ications of the orig inal equipment tires in­
stalled on your veh icle at the time it was man­
ufactured.
Federal law requires t ire manufacturers to
p lace standard ized information on the s ide­
wall of all tires c:>fig. 189. This information
i dent ifies and describes the fundamental
characterist ics, the quality grade of the tire
and a lso provides a tire ident ificat ion number f
or sa fety standard ce rtification and in case of
a reca ll.
Tire specifications
Knowledge of ti re specificat ions makes it eas­
ier to choose the correct tires. Radial ti res
have the tire specifications marked on the
sidewa ll, for examp le:
P2 65 / 35 R1 9 98Y XL
This co nta ins the following information:
P Indicates the t ire is for passenger cars
(where app licab le)
2 65 Nominal tire width in mm of the tire
from sidewall edge to sidewa ll edge. In
general, the larger the number, the wider
the tire
35 Height/w idth ratio in percent (aspect ra-
t io)
R Tire construction: Radial
1 9 Rim diameter code (in inches)
98 Load rating code
Y Speed rat ing letter code
X L (or "xl", "EXTRA LOAD", or "RF" Indicates
t h at the t ire is a"Re inforced" or an " Extra
Load " tir e
M+S (or "M/S") Indicates that the tire has
some mud and snow capabi lity
The tires could also have the information of
direction of rotat io n
c:> page 222 .
Tire manufacturing date
The manufact uring date is also indicated on
the tire sidewall (possibly on ly on the inner
s ide of the wheel) :
"DOT ... 2212 ... "means, for examp le, that
the tire was produced in the 22nd week of 2012.
Speed rating (letter c ode)
The speed rating letter code on the whee ls in­
dicates the maximum permissible road speeds
c:> & in Winter tires on page 238 .
P up to 93 mph (150 km/h)
Q u p to 99 mp h (158 km/h)
R up to 106 mph ( 170 km/h)

S up to 110 mph (180 km/h)
T up to 118 mph (190 km/ h)
U up to 124 mph (200 km/ h)
H up to 130 mph (210 km/h)
V up to 149 mph (240 km/h)
1
)
Z over 149 mph (240 km/h)1
)
W up to 168 mph (270 km/h)1
)
Y up to 186 mph (298 km/h)1>
Your vehicle is no rma lly facto ry equipped with
tires , which possess excellent driving cha rac­
ter istics and give yo ur Audi opt imum driving
comfort .
U.S. DOT Tire Identification Numbe r (TIN)
and tire manufactur e date
This is the t ire's "serial n umber". It beg ins
with the le tte rs "DO T" and indicates that the
tire meets all federal standards . The next two
numbers o r letters indicat e the p lant wher e it
was manufactured, and the l ast four numbers
represen t the week and year of manufacture.
For example, the numbers 2212 mean that
the t ire was produced in the 22nd week of
20 12. Th e other numbe rs a re marketing co ­
des that may or may not be used by the t ire
manufacturer. This informa tion is used to con­
tact consume rs if a t ire defect requires a re­
call.
Audi Original tire
T ires with the ident ificat ion "ROl" have been
specia lly matched w ith your Audi. We re com­
mend using only these t ires be ca u se they
meet the highest standards rega rding safety
and dr iving characteristics when used correct ­
l y. Your authorized A udi dealer wi ll gladly pro ­
vide you with more information .
Tire ply composition and materials used
The number of p lies ind icates the n umbe r of
l ayers of rubber-coated fabri c in the t ire. In
general, the greater the number of plies, the more weight a tire can s upport . Tire manufac ­
turers a lso must indic ate the mate rials in the
ll Fo r tires wit h a m ax im um s pee d ca pabil ity over
1 4 9 mp h (24 0 k m/h) , tire m an ufa ctur ers somet ime s
use th e let ters "ZR."
Tire s an d wheel s 235
tire, which incl ude stee l, nylon, po lyester, and
others .
Maximum Load Rating
This number ind icates the max imum load in
kil ograms and po unds that can be ca rr ied by
the tire .
Tire quality grading for treadwear ,
tract ion , and temperature resistance
T read wear, t raction and tempe ra tur e grades
<:!vpage 236 .
Maximum Permissible Inflation Pressure
This number is the greatest amount of a ir
pressure that should ever be put in the tire
u nder norma l dr iv ing cond itions .
.&_ WARNING
-Using incorrect o r unm atc hed tires and/
or wheels or improper tire and wheel
comb inat ions can lead to loss of control ,
collision and serio us personal in jury.
- A lways use t ires, rims and whee l bolts
that meet the specifications of original
factory- insta lled tires or other combina­
tions that have been specifically ap­ proved by the vehicle manufacturer.
- Tires age even if they are not being used
and can fai l sudden ly, especially at hig h
speeds. Tires that are more than 6 years
old can only be used in an emergency
and then w ith special care and at lower
speeds .
- Never mo unt used tir es on your veh icle if
you are not sur e of the ir "previo us histo­
ry ." O ld used tires may have been dam­
a ged even thoug h the damage cannot be
seen tha t can lead to sudden tire f ail u re
and loss of vehicle control.
- All f our whee ls must be fitte d wit h ra dial
tires of the same type, size (rolling cir­
cumference) an d the same tread pattern .
.
Driving with different tires reduces ~
•
•

236 Tire s and whee ls
vehicle handling and can lead to a loss of
control.
- If the replacement tire is not the same as
the tires that are mounted on the vehicle
- for example with winter tires - only use
the replacement t ire for a short period of
t ime and dr ive with extra care . Refit the
normal road wheel as soon as safely pos­
sible.
- Never drive faste r than the maximum
speed for which the tires on your veh icle
are rated because ti res that are driven
faster than their rated speed can fail
sudden ly.
- Overloading t ires cause heat build-up,
sudden tire failure, including a blowo ut
and sudden deflation and loss of control.
- T emperature grades app ly to tires that
are properly inflated and not over or un­
derinflated.
- For technical reasons it is not a lways
possible to use wheels from othe r
vehicles -in some cases not even wheels
from the same vehicle model.
- If you install wheel trim discs on the ve­ hicle whee ls, make sure that the air f low
to the brakes is not blocked . Reduced air­
flow to the brakes can them to overheat, increasing stopping distances and caus­
ing a collision .
- Run flat tires may only be used on
vehicles that were equipped w ith them
at the factory . The vehicle must have a
chassis des igned for run flat t ires and a
factory-installed t ire pressure monitor­
ing system* that indicates a loss of ti re
pressure. Incorrec t use of run flat tires
can lead to vehicle damage or accidents .
Check with an authorized Audi dea ler or
tire spec ialist to see if your vehicle can be
equipped with run flat tires . If run flat
tires are used, they must be installed on
all four wheels. M ixing tire types is not
permitted .
(D Note
-For technica l reasons, it is not genera lly
possible to use the wheel r ims from oth- er vehicles.
This can hold true for wheels
of the same vehicle type.
- If a rep lacement tire is different from
the tires that you have mounted on your
vehicle (for example winter tires or wide profile tires), then use the rep lacement
tire for a short period of time only and dr ive with extra care. Replace the flat tire
w ith the tire match ing the others on your
vehicle as soon as possible.
- Never drive without the valve stem cap .
The valves could get damaged .
® For the sake of the environment
D ispose of o ld tires in accordance with the
local requirements .
Uniform tire quality grading
-Tread wear
- Traction AA A B C
- Tempe rature ABC
Quality grades can be found where applicab le
on the t ire s ide wall between tread shou ld er
and maximum section width c> page 233,
fig. 189 .
For exampl e: Tread wear 200 , Traction AA,
Temperature A.
All passenger car t ires must conform to Feder­
al Safety Requirements in addition to these
grades.
Tread wear
T he tread wear grade is a comparative rating
based on the wear rate of the t ire when tested
u nder controlled conditions on a specified
government test course .
For example, a tire graded 1S0 would wear
one and one ha lf (11/2) times as well on the
gover nment course as a t ire graded 100 .
The relative performance of tires depends upon the actual conditions of their use, how­
ever, and may depa rt s ignificantly from the
norm due to va ria tions in d riving hab its, serv­
ice practices and differences in road character-
istics and climate.
ll-

Traction
The traction grades, from highest to lowest,
a re AA, A, Band
C. Those grades represent the
tire's ability to stop on wet pavement as
measured under controlled conditions on
specified government test surfaces of asphalt
and concrete . A tire marked C may have poor
traction performance¢ .&..
Temp eratu re
The temperature grades are A (the highest),
B, and
C, representing the tire 's resistance to
the generat ion of heat and its ability to dissi­
pate heat when tested under controlled condi­
tions on a specified indoor laboratory test
wheel.
Sustained high temperature can cause the
material of the tire to degenerate and reduce
tire life, and excessive temperature can lead
to sudden tire failu re ¢ .&. .
The grade C corresponds to a level of perform­
ance which all passenger car tires m ust meet
u nder the Federa l Motor Ve hicle Safety Stand­
ard No. 109. Grades Band A represent higher
l eve ls of pe rformance on the laboratory test
wheel than the m inimum required by law.
_& WARNING
Th e traction grade assigned to this tire is
based on stra ight-ahead b raking t raction
tests, and does not include acceleration,
cornering , hydrop laning or peak traction
character istics.
A WARNING
The temperature grade for this t ire is es ­
tablished for a t ire that is properly inflated
and not overloaded. Excessive speed, un­
derinflation, or excessive loading, either
separate ly or in combination, can cause
heat buildup and possibl e tire fa ilu re.
-
Tire s an d wheel s 237
Winter tires
Winter tires can improve vehicle handling on
snow and ice . At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires.
In some heavy snow areas, local governments
may require true w inter o r "snow" tir es, those
with very deeply cut t read. These tires should
o nl y be used in pairs and be installed o n all
f o ur wheels . Make sure you p urchase snow
ti res that are the same size and cons truc tion
type as the other tires on yo ur vehicle .
You r vehi cle is equipped wi th a ll w heel d rive,
th is w ill imp rove trac tion duri ng win ter driv­
ing, even with the standa rd tires. However, we
strong ly recommend that you always equip all
fo ur wheels on your vehicle with correctly fit­
ted winter tires or a ll-season tires, when win ­
ter road cond itions are expected. This also im­
proves the veh icle's brak ing performance and
reduces stopping d ista nces .
Summer tires provide less grip on ice and
snow.
Winter tires (snow tires) must always be fitted
o n all fo ur whee ls .
As k your au thori zed A udi d ealer or qualified
workshop for permit ted
winter tire size s. Use
o nl y radial winter ti res .
Win ter tires lose their effec tiveness whe n the
tread is worn down to a dep th o f 0.15 7 inch
(4 mm) .
Only d rive w it h w inte r tir es under w inte r con­
di tions. S umme r tir es handle bette r whe n
t h e re is no s now o r ice on the ro ad s an d the
temperature is above 45 ° F (7 °C) .
I f you have a flat t ire, see notes on rep lace­
ment wheel¢
page 233 .
Please always remember that winter tires may
have a lowe r sp eed rating than the tires o rig i­
nally i nstalled on your veh icle at t he time it
was ma nufactu red. Please see ¢
page 234,
Speed ra ting (letter code)
for a lis ting o f th e
speed ra ting lette r codes and the max imum
speed at which the tires can be driven .
111>-
•
•