2013 AUDI Q7 Owner´s Manual

fall f rom a lift if the re is a change in ve­
h icle we ight d istr ibut ion and balance.
This might happen, for examp le, when
heavy components such as the engi ne
b lock or transmiss io n are removed .
- Whe n removing heavy components like
these, ancho r vehicle to ho ist o r add cor­
r e spond ing w eig hts to ma intai n the cen ­
te r of g ravity . Othe rwise, the vehicl e
mi ght til t or slip off th e hoi st, causi ng
s er ious perso nal inju ry.
(D Note
- Be awa re of th e f ollowing po in ts b efore
li fting t he vehi cle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission housing, the
front or rear axle or the body side
members. This could lead to serious
damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­ ance between the hoist and low parts
of the vehicle .
Emergency situations 319
•
•

320 General information
General information Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::>page 322. This sec ­
tion provides general information, notes and
restrictions which apply to this data .
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker.
Fig. 282 Veh icle Ide ntific atio n Number (VlN) p late: lo ­
cation on driver 's sid e das h panel
Fig. 283 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
b le from the outside through the windshield
r:::> fig . 282 . You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select !CAR lfunc tion button>
Systems*
control button > Vehicle ID number (V IN) or
ICARI function button >
Car systems * control
button >
Servicing & checks > VIN number . The
vehicle identification label
is located in the luggage compartment under
the cargo floor cover.
The label¢
fig. 283 shows the following vehi­
cle data :
(D Production control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is you r assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
time the vehicle was manufactured . You can
find this sticker on the left door jamb.
It
shows the month and year of production and
the ve hicle ident ification number of your vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carr ier .
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are Listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oi l and coolant, plus maximum load, wh ich in­
cludes passenger weight (lSO lbs/68 kg per
Ill>

designated seating position) and luggage
w eight ~&. .
Gros s Axle W eight Rating
The G ross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle
q .&. .
Vehicle capacit y weight
The vehicle capac ity we ight (max . load) is list­
ed on the driver 's side B-p illar.
Roof weight
The maximum permissible roof weight is 2 20
lb (100 kg ).
The roo f weight is made up o f
the we ight of the roof rack system and the
weight of the object be ing transported
q page 84, Loading the roof rack.
..&, WARNING
- The Gross Vehicle Weight Rat ing for yo ur
vehicle, found on the sa fe ty compliance
label on the driver's side B -pillar , must
never be exceeded under any circumstan­
ces. Exceeding the Gross Vehicle Weight
Rating of your vehicle is likely to damage
your vehicle, and such damage will not be covered by your Lim ited New Vehicle
Warranty . Exceeding the Gross Vehicle
We ight Rating will also change the per­
formance and handli ng characterist ics of
yo ur vehicle , which cou ld cause a crash
result ing in serious in jury or death.
- The Gross Vehicle Weight Rat ing for your
vehicle would be exceeded if yo ur vehicle
is simultaneous ly equipped with Pano r­
amic sliding sunroof; third-row seating;
trailer towing equipment (factory or
dealer-installed), and running boards
(dealer-installed) . UNDER NO CIRCUM­
STANCES MAY ALL SUCH ITEMS BE IN­
STALLED ON T HE SAME VEHICLE .
- The actual Gross Axle Weight Rat ing at
the front and rear axles shou ld not ex ­
ceed the perm iss ible weights, and their
combination must not exceed the G ross
Vehicle Weight Rat ing .
Gene ral in formation 32 1
-Exceeding perm iss ible weight ratings can
result in veh icle damage, acc idents and
personal injury.
([) Note
-The ve hicle capacity weight figu res apply
when the load is d istr ibuted evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to
the rear axle as poss ible so that the vehi­
cle's handling is not impaired .
- Do not exceed the maximum permissible
axle loads or the maximum gross veh icle
we ight. Always remember that the vehi­
cle's handling w ill be affected by the ex­
tra load. Therefore, ad just yo ur speed ac­
co rding ly.
- Always observe local regulat ions .
Dimensions
T he specifications refer to the basic model.
D ifferences may occur depending on the mod­
el type and op tions ordered , fo r example , tire
sizes .
Q) Note
When dr iv ing up steep ramps, on rough
r oads, over c urbs, etc. it is important to re ­
member that some parts of your vehicle,
such as spoi lers or exhaust system compo­
nents, may be close to the ground. Be
careful not to damage them .
•
•
I

322 Data
Data
280 hp, 6-cylinder engine, with all-wheel drive
Engine data Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dimensions (approx .)
Length (with license plate bracket)
Width (with outside mirrors folded) Height (unloaded)
Turning circle diameter (curb to curb)
Capacities (approx .)
Fuel tank
- Total capacity
- Reserve (of total capacity) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm) 280@ 4900
-6500
-·--295@ 2150 -4900
6 cylinder
-·~-182 .8 (2995)
3 .50 (89.0)
3 .33 (84 .5)
--· 10.5 : 1
Premium unleaded (91 AKI) Recommended for
maximum engine performance. Further details
¢page 256, Fuel supply
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39 .4 (12)
gal (liters) 26.4 (100)
gal (liters) 2.6-3.2 (10 -12)
Windshield and headlight* washer fluid container quarts (liters) 4.8 (4 .5)
Engine oil with filter change quarts (liters) 7.2 (6.8)

Data
333 hp, 6-cylinder engine, with all-wheel drive
Engine data
Maximum output SAE net
Maximum torque SAE net
No. of cylinders
Displacement
Stroke
Bore
Compression ratio
Fuel
Dim ension s (appro x.)
Leng th (with license pla te bracket)
Width (with outside mirrors folded) He igh t (unloaded)
T urning circle diameter (curb to curb)
Capacit ies (appro x.)
Fuel tank
- Total capacity
- Reserve (o f total capacity) 333@ 5500 - 6500
hp@rpm
lb-ft@ rpm
-~~-
CID (cm3
)
in (mm)
in (mm)
--·
325 @ 2900 - 5300
6 cylinder
182 .8 (2995)
3 .50 (89.0)
3 .33 (84.5)
10.5 : 1
Premium unleaded (91 AKI) Recommended for
maximum engine performance. Further details
<=> page 256, Fuel supply
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39 .4 (12)
gal (liters) 26 .4 (100)
gal (lite rs) 2 .6 -3.2 (10 -12)
Windshield and headlight* washer fluid container quarts (liters) 4 .8 (4 .5)
Engine oil with filter change quarts (liters) 7
.2 (6 .8)
323
•
•

324 Data
240 hp, 6-cylinder engine, with all-wheel drive
Applies to vehicles: with diesel engine
Engine data
Maximum output SAE net
Maximum torque SAE net
No . of cylinders
Stroke
Bore
Compression ratio
Fuel
Dimen sions (approx .)
Length (with license plate bracket)
Width (with outside mirrors folded)
He ight (unloaded)
Turning circle diameter (curb to curb)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity) hp@ rpm
lb-ft@ rpm
CID (cm
3 )
in (mm)
in (mm) 240@ 3500 - 4000
-·--406@ 1750 - 2250
6 cylinder
-•--
181.1 (2967)
3 .60 (91.4)
3.27 (83 .0)
~-· 16.8: 1
ULSD-Diesel No. 2 Further details<=>
page 257, Die­
sel fuel
in (mm) 200.3 (5089)
in (mm) 78.1 (1983)
in (mm) 68.4 (1737)
ft (m) 39.4 (12)
gal (liters) 26.4 (100)
gal (l iters) 2.6-3.2 (10-12)
Windshield and headlight* washer fluid container quarts (liters)
4.8 (4.5)
Engine oil with filter change quarts
(liters) 8.1 (7. 7)

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
If you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage ;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment ;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside North America .
Consumer Information 325
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, service or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduction. Service Manuals and liter­
atu re are availabl e to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty
&
Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures ,
in very dusty regions, when towing a tra iler
very frequently, etc., some serv ice work
shou ld be pe rformed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter .
® For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus min imizi ng adverse
effects on the environment .
Important considerations for you and
your vehicle
The increasing use of electronics , sophisticat­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technica l ..,_
•
•

326 Consumer Inf ormation
comp lexity of today's automobi les, have
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Also, s afety an d e nvir onm ent al con­
cerns place very strict limits on the nature of repairs and adjustments to engine and trans ­
miss ion pa rts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment avai lab le to specially trained
workshop personnel in order to assure proper
performance, reliab ility and safety of the vehi­
cle and its many systems .
Improper ma intenance, adjustments and re ­
pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­ ranty. Therefo re , proof of servici ng in accord­
ance w it h the ma intenance sched ule may be a
condition for upholding a poss ible warranty
claim made within the warran ty period.
Above all, operational safety can be adve rsely
affected, c reating unnecessary risks for you
and your passengers.
If in doubt about any serv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give your authorized
Audi dealer the opportunity to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, or iginal parts
and tra ined spec ialists to keep your vehicle
running properly .
Performing lim it e d m aint en anc e y ourself
The fo llowing pages describe a limited num­
ber of procedures which can be performed on
you r vehicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and ca refully follow the instruc­
tions given. Always rigorously obse rve the
WARNINGS p rovided .
Before you ch eck anything in th e engin e
compartme nt, alway s read an d heed all WARNINGS
¢ & a
nd ¢ & in Working in the
engine comportment on page 264 .
A WARNING
--Serious personal in jury may occur as a re-
sult of improperly performed mainte­ nance, adjustments or repa irs.
- Always be extremely careful when work­
ing on the vehicle. Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r isk personal
in jur y.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re­ spect to the ve hicl e, or are uncerta in how
to proceed .
- Do not do any work withou t the proper
too ls and equipment . Have the necessary
work done by your authorized A udi deal ­
er or anothe r properly equipped and
qualified workshop.
- The engine compar tment o f any motor
vehicle is a potentially hazardous area. Never reach into the area around or
touch the rad iator fan. It is temperature
control led and can sw itch on suddenly -
even when the engine is off and the igni­
tion key has been removed. The rad iator
fan switches on automatically when the coo lant reaches a certai n tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always remove the ign ition key befo re
a nyone gets under the veh icle.
- Always suppor t your veh icle with safety
s tands if it is necessary to work under­
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this pur ­
pose and co uld co llapse causing serio us
personal injury.
- If you must work unde rneath the vehicle
wit h the wheels on the ground, a lways
make sure the vehicle is on leve l ground,
that the wheels are always secure ly
blocked and that the engine cannot be
started.