2013 AUDI Q7 spare tire

What do I do now?
Jack, tools and
inflatable spare tire
Tools
The tool kit is located in the luggage com­
partment under the cargo floor cover.
F ig . 257 Luggage compa rtme nt: ve hicle tool ki t
The on board tool kit includes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt cove rs*
- Wheel bolt wrench
- Alignment pin for changing wheels
- Screwdriver with reversible blade
- 10 x 13 open ended wrench
- Towing eye
@ Tips
Some of the onboard items listed above
are prov ided on certa in models only or are
optional extras .
What do I d o now ? 301
Jack and folding chocks
The jack and the folding chocks are located in
the luggage compartment under the cargo
floor cover.
F ig . 258 Luggage compar tme nt ve hicle jack and fold ·
i ng chocks
--------
F ig. 259 Opening fo ldi ng chocks
Vehi cle jack
The jack is located under the tool kit
¢ fig . 258. Before storing the jack, make sure
it is wound back down as far as it will go.
Folding chocks
Two unassembled fo lding c hocks are attached
to the foam section at the front with the jack
¢fig . 258.
Re lease the two hook-and-loop fasteners, and
remove the two chocks. To use the chocks, you
first have to raise the support plate
¢ fig . 259 (D and then insert the locking plate
with the two "tabs" into the elongated ho les
in the base plate @¢.&. .
A WARNING
-The chock cannot fulfill its function and
may lose its stability if the "tabs" on the
support p late are not inse rted co rrectly
into the elong ated holes in the base

302 What do I do now ?
plate. If this happens, the vehicle may
start to move while a wheel is being changed.
- Never use the folding chocks if they are
damaged or if they have not been assem­
bled correctly.
A WARNING
Improper use of the vehicle jack can cause
ser ious persona l injuries.
- Never use the jack supplied with your
Audi on anothe r vehicle, particularly on a
heavier one. The jack is only suitable for
use on the vehicle it came w ith.
- Us ing a bumper jack to raise the vehicle
will damage the bump er system. The
jack may slip, causing in jury.
- Never support your veh icle on cinder
blocks, b ricks or other objec ts. These
may no t be ab le to suppor t the load and
c ou ld cau se injury whe n they fail.
- Never start o r run the engine while the
vehicle is supported by the j ack.
- If you must wo rk under the vehicle, al­
ways use safety stands specifically de­
signed for this purpose.
- Always make su re the inf latable spare
ti re and even a flat tire a re se cu red in
pla ce and not loose, otherwise t hey
c ou ld f ly forward, causing personal in jury
to passengers in the veh icle in an acc i­
dent o r sudden mane uver.
Removing bass box
Applies to vehicles: with bass box
Before the inflatable spare tire can be taken
out, the bass box must be removed .
Fig. 260 Spare wheel well: Bass box
Removing bass box
" Squee ze the locking tabs ¢ fig. 260 (!) of
the connector .
" Disconnect the connector @and place the
lead to one side.
" Turn t he large screw counter-clockwise.
" Carefully
remove the bass box.
Installing bass bo x
" Carefully place t he bass box in the wheel.
The insc ription "FRO NT" on the bass box
m ust face forward .
" Reconnect the connector that was removed.
" Secure the bass box with t he large screw.
· Inflatable spare tire
The inflatable spare tire expands to its full di­
ameter when it is inflated.
Fi g. 2 61 In flatable spare t ire w ith compressor
Removing inflatable spare tire
" Lift up the cargo floor us ing the handle .
" Tu rn the large screw¢
fig. 261 co unter-
clockwise.
" Remove the bass box as required
¢page 302.
" Take out the inflatable spare tire .
" Always sto re the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
¢page 171.
Stowing the inflatable spar e tire
" Release the air by unscrewing the valve
stem.
" Screw the valve stem back in afterwards .
" Wait a few hours befo re p lacing the wheel
in the spare whee l we ll
r=:, _.&.
" Install the bass box as required r=:, page 302 . ..,.

• Secure the wheel with the large screw.
• Fold the cargo floor back down.
After using the inflatable spare wheel
The inflatable spare tire can be re-used as
long as it is not damaged and is not worn
down to the tread wear indicators~.&. .
When you let the air out of the inflatable
spare tire, it does not assume its folded shape
again for several hours. Until then, it cannot
be placed back in the spare wheel well and
stowed securely.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the inflatable spare tire is more than 6
years old, use it only in an emergency
and with extreme caution and careful
driving .
- The inflatable spare tire is intended only
for temporary and short-term use .
It
should be replaced as soon as possible
with the normal wheel and tire.
- The tire pressure value for the inflatable
spare tire is located on the driver's side
B-pillar ~page284,
fig . 252.
-Maximum permissible speed is 50 mph
(80 km/h).
- Avoid full-throttle acceleration, heavy
braking, and fast cornering.
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for several hours . Until then, it
cannot be placed back in the spare wheel
well and stowed securely.
- Never drive with more than one inflata­
ble spare tire.
- For technical reasons, the use of tire
chains on the inflatable spare tire is not
permitted. If it is necessary to drive with
tire chains, the inflatable spare wheel
must be mounted on the front axle in the
event of a flat in a rear tire. The newly
available front wheel must then be in­
stalled in place of the rear wheel with
What do I do now? 303
the flat tire. Installing the tire chain be­
fore mounting the wheel and tire is rec­
ommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard braking or in an accident.
Never store the inflatable spare tire or
jack and tools in the passenger compart­
ment.
(D Note
- The inflatable spare tire has been devel­
oped specifically for this vehicle model.
It must not be exchanged or used for
other vehicle models. Similarly, inflata­
ble tires from other vehicle models must
not be used.
- Normal summer or winter tires must not
be installed on the inflatable tire rim.
Inflating inflatable spare tire
• Remove the compressor from the luggage
compartment ~
page 302, fig. 261.
• Unscrew the valve stem from the spare tire.
• Screw the tire filler hose from the compres­
sor firmly onto the valve of the spare tire.
• Insert the plug from the compressor into an
outlet of the vehicle~
page 87.
• Switch the compressor on .
• Let the compressor run until the value
specified on the tire pressure label is
reached
~ page 284, fig. 252. Switch the
compressor off after running for 12 minutes
at the most -danger of overheating!
A WARNING
-
The compressor and the tire filler hose can
become extremely hot while they are run­
ning -danger of burns!
(D Note
Switch the compressor off after running
for 12 minutes at the most -danger of
overheating! Allow the compressor to cool
down for a few minutes before you use it
again .
•
•

304 What do I do now?
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang ­
ing a wheel .
• After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop ¢,& .
• All passengers should
leave the car and
move to a safe location (for instance, behind
the guardrail) ¢
A-
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally ¢,& .
• Move
selector lever to position P <=> ,&.
• If you are towing a trailer: unhitch the trail­
er from your vehicle.
• Block the diagonally opposite wheel wi th
the folding chocks or other objects.
• Take the
jack and the inflatable spare tire
out of the luggage compartment
¢page 301.
11. WARNING
=
You or your passengers could be injured
while changing a whee l if you do not fol­
low these safety precautions :
- If you have a f lat tire,
move a safe dis­
tance off the road . Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists .
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed with the fold­
ing chocks or other objects. When one
front whee l is lifted off the ground, plac­
ing the Auto mat ic Transmission in "P"
(Park) will
not prevent the vehicle from
moving .
-
-Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- After installing the inflatable spare tire,
make sure that you replace the flat tire/
wheel in its storage area properly and
tighten the knurled retaining screw se ­
curely .
' Changing a wheel
When you change a wheel , follow the se­
quence described below step-by-step and in
exactly that order .
l. Activate the vehicle jack mode (only
vehicles with Adaptive Air Suspension)
¢ page 159.
2. Remove the decorative wheel cover* . For
more details see also ¢
page 305, Deco­
rative wheel covers
or ¢ page 305,
Wheels with wheel bolt caps.
3. Loosen the wheel bolts¢ page 305.
4. Locate the proper mounting point for the
jack and align the jack be low that point
¢ page 306.
5. Lift the car with the jack¢ page 306.
6. Remove the wheel with the flat tire and
then install the
inflatable spare tire
¢page 307 .
7. Tighten all whee l bolts lightly.
8.
Lower the vehicle with the jack .
9. Use the wheel bolt wrench and
firmly
tighten all wheel bolts¢ page 305.
10. Rep lace the decorative wheel cover*.
11. Deactivate the vehicle jack mode (only
vehicles with Adaptive Air Suspension)
¢page 159.
A WARNING
Always read and follow all WARNINGS and
inf ormat ion¢ .&.
in Raising the vehicle on
page
307 and ¢page 308.

_& WARNING
-You or your passengers could be injured
while changing a wheel if you do not
follow these safety precautions:
- Position the jack only at the designated
lifting points and align the jack. Other­
wise, the jack could slip and cause an
injury if it does not have sufficient hold
on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping .
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
(D Note
Do not lift the vehicle by the sill. Position
the jack only at the designated lifting
points on the sill. Otherwise, your vehicle
will be damaged.
What do I do now? 307
Taking the wheel off/installing the inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
Fig. 267 Chan gin g a w hee l: alignment p in inside the
to p ho le
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows :
Removing the wheel
.. Remove the topmost wheel bolt completely
and set it aside on a
clean surface.
.. Screw the threaded end of the
alignment
pin from the tool kit hand-tight into the
empty bolt hole
~ fig . 267.
.. Th en remove the other wheel bolts as de­
scribed above.
.. Take off the wheel leaving the alignment
pin in the bolt hole
~ 0.
Putting on the inflatable spare tire
.. Inflate the inflatable spare tire ~ page 303
and push the wheel over the alignment pin.
.,. Screw in and tighten all wheel bolts
slight­
ly.
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest .
.. Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bolts firmly ~
page 305. Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.

308 What do I do no w?
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
- When mounting tires with
unid irection al
tread design
make sure the tread pat­
tern is pointed the right way
¢ page 308 .
-The wheel bolts should be clean and easy
to turn. Check for d irt and corrosion on
the mat ing surfaces of both the wheel
and the hub . Remove all dirt from these
su rfaces before remount ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in
the right direction.
Using a spare t ire w ith a tread pattern
int ended fo r use in a specific direct ion
When us ing a spa re tire w ith a t read patte rn
i n te nded for use in a specific direction, p lease
note the fo llowing:
- The direction of rotation is marked by an ar­
row on the side of the tire .
- If the spare t ire has to be in stalled in the in ­
correct d irection, use the spare tire only
temporarily since the t ire will not be able to
a chieve its optimum perfo rmance character­
ist ics w ith reg ard to aquapl ani ng, noise and
wea r.
- We recommend tha t you pay pa rticular at ­
tent ion to this fact du ring wet weather and
that you adjust your speed to ma tch road
conditions .
- Replace the fla t tire w ith a new one and
have it installed on your veh icle as soon as
poss ible to restore the handling advantages
of a unid irect iona l tire .
Notes on wheel changing
Please read t he i nfo rmat ion Q page 291 , New
tires and replacing tires and wheels
if yo u are
go ing to use a spa re tire which is different
from the tires on yo ur vehicle.
After you change a tire:
- Check the tire pressure on the spar e imm e­
diately after installation .
- Ha ve the wheel bolt tightening torque
ch ecked with a torque wr ench as soon a s
po ssible by your authorized Audi deal er or
a qua lifi ed workshop.
- With steel and alloy wheel rim s, the wheel
bolt s are corre ctly tightened at a torque of
120 ft lb (160 Nm) .
- If you notice that the wheel bolts ar e cor ­
roded and difficult to turn while changing
a tir e, they should be repla ced before y ou
c h eck the tightening torque .
- Re pla ce the flat tire wi th a new on e and
have it in stalled on y our vehi cle a s soon a s
po ssible. Remount the wheel cover.
Until th en , dr iv e with extra car e and at re­
duc ed sp eed s.
&_ WARNING
-
- If you a re going to eq uip your vehi cle
with tires or rims which differ from those
which were factory installed, then be
sure to read the information
Q page 291,
New tires and replacing tires and
wheels.
- Always make s ure the damaged wheel o r
even a flat tire and the jack and tool kit
are property secured in the luggage com­
partment and are not loose in the pas­
senger compartment .
- In an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
ve hicle .
- Always store damaged wheel, jack and
too ls securely in the luggage compa rt ­
ment. Othe rwise, in a n accident o r sud­
den maneuve r they could f ly forwa rd ,
causing inj ury to passengers in the ve hi­
cle .

Index 337
-----------------------------------.......
Hill hold
Starting on hills 110
H omelink ® universal remote contro l 161
Hood Opening 264
Release lever ............. ... ... .. 264
H orn ..... .. .. .. .. .. .... ... .. .. .... . 8
H ow are c hild restra int system anchors re -
la ted to child sa fe ty ........ .. .. .. .. . 218
H ow many airbags does my vehicle have? 191
H ow often sho uld I check my tire pres-
sures? . ..... .. .. ... ..... ... .. .. ... 287
H ow sa fe ty belt pre tensione rs wo rk . .. . 18 2
H ydroplani ng ............. .... .. ... 291
I
Ignition key . . . . . . . . . . . . . . . . . . . . . . . . 105
I gnition lock . .... ......... .... .. .. . 10 5
M alfunct ion . . . . . . . . . . . . . . . . . . . 34, 3 7
Ignition lock pos itio ns ...... .. .. .. .. . 105
Important things to do before driving . . 165
I mp ro perly wor n safety be lts . .. .. .. .. . 18 2
Indicato r lights . . . . . . . . . . . . . . . . . . . . . . 14
A irbag system .............. .... .. 195
P ASSENGER AIR BAG OFF ...... ... .. 195
Infant seats . ............. .... .. ... 211
I nfl atable spare t ire ........ .. .. .. .. . 30 2
I nflating ... ... .. ..... ... .. .. .. ... 30 3
Install ing ch ild safety seats
Safety belts . . . . . . . . . . . . . . . . . . . . . . 215
Instal ling the upper tet her strap on the
anchorage . .. .. ........... .. .. .. ... 223
I nstrument cluste r ill umination . ... .. .. 13
Instrumen ts and cont rols . ...... ... ... 10
Gene ral i llus tra tion ....... .. .. .. .. ... 8
Inter ior lights
Front .. .. .. .. .... ...... ... .. .. .. .. 61
Rear .. ... ... ................ .... . 61
Intermittent w iping
Ra in sensor . .... ......... .... .. .. .. 63
J
Jac k 301
J ump-start ing .... ...... ... .... .. ... 3 14
J umper cables ............. .... .. ... 315
K
Key ... ... .. .. .... ... .. .. ..... ... .. . 38
Battery replacement . .. ..... ... .. .. . 40
Coded settings ..... . .. .. ..... ... .. . 91
Convenience opening and closing of win -
dows ....... .. ...... ............. . 53
Emergency key . . . . . . . . . . . . . . . . . . . . . 38
Key rep lacement . . . . . . . . . . . . . . . . . . . 38
Master key . . . . . . . . . . . . . . . . . . . . . . . . 38
Valet key . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Key coded settings Climate controls .. .... ............. . 91
Keyless ent ry remote cont ro l ... ... .. .. . 38
K ick-down
t ipt ron ic® . .. .. .. .... ........... .. 140
L
LATC H 218
Desc ription .. .. .. .. . ...... ...... .. 219
G ui dance fixtures for lower anc ho rages 220
Installing a ch ild restr aint ....... .. .. 22 1
L oca tion . ... .... .. . .. .. ..... ... .. 219
Mo unting and releasing the anchorage
hoo k ... .. .. .... .. . .. .. ..... ... .. 221
Late ra l ang le .. .. .. .... ........... .. 238
Leather ...... .. .. .... ............. 252
Cleaning .. .. .. .. .. . .. .... .... .. .. 253
Leve l adj ustment
refer to Adapt ive A ir Suspension . 155, 157
L ift ing jack . .. .. .. .... ............. 306
Lifting vehicle . .. .. .. . ....... ..... .. 318
Light Exte rior lig hting i n the mirror housing . . 59
l eav ing home .. .. ................. . 59
also refer to Amb ience lighting .... .. . 62
Ligh ting
refer to Ambience lighting . . . . . . . . . . . 62
Light ing in the m irror housing . ... ... .. . 59
Lights ... .. .. .. .. .. ............... . 57
Coming h ome . . . . . . . . . . . . . . . . . . . . . . 58
Daytime runn ing lights ............ .. 58
E mergency flashe rs . . . . . . . . . . . . . . . . . 60
E xterior lig hts ... .. . .. .... .... .. .. . 58
F ron t fog lights . . . . . . . . . . . . . . . . . . . . 58
H ead ligh ts .. .. .. .... ............. . 57
Hig h beam . . . . . . . . . . . . . . . . . . . . 57 , 60
•
•