2013 AUDI Q5 ignition

10 Instruments and warning/indicator lights
Instruments and warning/indicator Lights
Instruments
Instrument cluster and controls
The instrument cluster is your central source of information.
Fig. 3 Overv iew of the instrument cluster
Hybrid drive*: the instrument cluster var ies
c:> page98 .
(D Coolant temperature gauge 10
@ Tachometer . . . . . . . . . . . . . . . . 11
@ Warning/indicator lights . . . . . . 14
© ISETlbutton .. .. . . .. . . . . . . . . 11
® Display
- Driver information system 20
- Time and date display . . . . . . . 12
- Odometer . . . . . . . . . . . . . . . . 13
@ Reset button for trip odometer . 13
(j) Speedometer
@ Fuel gauge . . . . . . . . . . . . . . . . . 12
(D Tips
The illumination for the instrument cluster
lights up whenever you switch on the igni­
tion with the
vehicle headlights off . As
the daylight fades, the instrument cluster
illuminat ion likewise dims automatically
and will go out completely when the out­
side light is very low. This feature is meant
to remind you to switch on the headlights
when outside light condit ions become
poor.
Engine coolant temperature gauge
The engine coolant gauge q page 10, fig. 3 (D
only works when the ignition is on. To prevent
damage to your engine, please note the fol ­
lowing important po ints:
Engine cold
If the needle is at or close to the bottom of
the gauge, the engine has not yet reached its
operating temperature. Avoid high engine
speeds, heavy engine loads, and heavy throt ­
tle app lications.
Normal temperature
When the engine has reached its operating
temperature, the needle will move to the mid­
dle of the gauge and remain there . If the en­
gine is working hard at high outs ide tempera­
tures, the needle may move higher on the
gauge. This is not a cause for concern as long
as the . warning light in the instrument
cluster display does not illuminate. .,..

12 Instruments and warning/indicator lights
button. You can perform an Auto-Check se­
quence when the vehicle is stationary and the
ignition is turned on or when the vehicle is
moving s lower than 3 mph (5 km/h).
The number of keys programmed to the vehi­
cle is also displayed. The disp lay
L2 3/3 indi­
cates that three keys have been programmed.
This allows you to make sure you have re­
ceived all of the keys when you purchase a
used vehicle .
For examp le, if you on ly receive two keys, you
should take those keys to your authori zed
Audi dealer to have the missing key deactivat­
ed so it cannot be used . You should also re ­
port the m issing key to your insurance compa­
ny.
Calling up the driver information
A yellow or red symbol appears in the instru­
ment cluster display, usually with a driver
message . The driver message display disap ­
pears after about
5 seconds. The driver mes­
sage can be displayed aga in by briefly press­
ing the
! SET i button.
Setting the speed warning
By pressing the I SETI button briefly, you can
set threshold 1 of the speed warning while
you are dr iv ing
c:> page 94 . By ma inta in ing
p ressu re on the
ISETI button, you de lete the
warn ing threshold.
Digital clock with date display
Fig . 5 Instrument cl uste r: t im e an d date
M N
9 a:
l:l
Depending on the vehicle equipment level,
you may choose between the quartz clock or the GPS contro lled clock*
(!i in the radio or in the
MMI*. You can learn more about this in
the MMI manual or in the radio user's manual.
(D Tips
-When you switch off the ignition or open
the drive r door, the time, date, odome­
ter and temperature are displayed for an
add itiona l
30 seconds .
- Yo u can also call up the display with the
!SET i button r=> page 11 wh ile the igni­
tion is switched off.
Fuel gauge
The fuel gauge works only when the ignition is
on.
When the needle reaches the reserve mark,
the
c:> page 33 1] symbol appears in the in­
strument cluster d isplay as well as the mes­
sage
Please refuel. This message is meant to
remind you to
refuel.
The total tank capacity of your vehicle is listed
in
r=> page 292.
(D Note
Never run the tank completely dry! An ir­
regular supply of f uel can cause engine
misfiring and fuel could enter into the ex­
haust system. The catalytic converter
could then overheat and be damaged .

Instrument s and warning /indicator lights 13
Odometer
The odometer indicates the distance driven.
Fig. 6 Instrument cluster: odometer
Fig. 7 Instr ument cluster: reset button
The display of distance driven is shown in kilo­
meters "km" or in "m iles".
- USA models -Miles
- Canada models -Kilometers
You can switch from kilometers to miles or
vise versa in the radio or in the MMI*. You can learn more about this in the MM
I manual or in
the radio user 's manual.
Odometer /trip odometer
T he odometer shows the total number of kilo­
meters or m iles that have been driven on the
vehicle.
The trip odometer shows the distance driven s ince it was last reset.
It can be used to meas­
ure short distances . The last digit shows dis­
tances of 100 meters or 1/10 of a mile.
The trip odometer can be reset to zero by pressing the reset button
10 .019 fig. 7.
Malfunction message
If there is a malfunction somewhere in the in­
strument cluster,
dEF will appear in the trip
odometer and w ill stay on. Contact your au­
thorized Audi dea ler to have the prob lem cor­
rected.
{t) Tips
- When you switch off the ignition or open
the driver door, the time, date, odome­
t er and temperature are displayed for an
additional 30 seconds.
- You can also call up the display with the
!SET ! button ~ page 11 while the igni­
tion is switched off.

Instrument s and warnin g/indic ator ligh ts 15
USA model s: Parking brake
¢page 18
Canada m odel s: Park ing brake
¢page 18
USA model s: Brake malfunction
¢page 18
Canada mod els : Brake malfunc­
tion
¢page 18
In vehicles with adaptive cruise control* addi ­
tional indicator lights are displayed
¢ page 109.
.8, WARNING
-Failure to heed warning lights and other
important vehi cle information may result
in serious personal injury or vehicle dam­
age.
- Whenever sta lled or s topped for rep air,
move the vehicle a safe distance off the
road, stop the engine, and turn on the
emergency flasher
¢ page 52.
- The engine compartment of any motor vehicle is a potentially hazardous area.
Before you check anything in the engine
compartment, stop the engine and let it
cool down. Always exercise extreme cau­
t ion when working under the hood
¢ page 226, Engine compartment
(D Tips
Many functions are monitored by the Auto­
Check system ¢
page 2 7. Malfunctions
or faults will be identified either w ith a red
symbol (pr iority 1 -Danger!) or with a yel­
low symbol (prior ity
2 -Warning).
EPC Electronic power control
This warning/indicator light monitors the
electronic power control .
The~ warn ing/ indicator light (Electron ic
Power Control) illuminates when you turn on
the ignition as a function check.
(D Tips
If this warning/indicator light illuminates
while yo u are driving, then there is a mal­
funct ion in the engine electronics. Have
the malfunct ion corrected as soon as pos­
sible by your authorized Audi dealer or
qualified workshop .
;;,/C; Electronic Stabilization Control
(ESC)
If the JiJ indicator lamp blinks whi le driving,
the ESC or ASR (Anti-Slip Reg ulation) is active­
ly regu lating.
If the
DJ i ndicator lamp illuminates , the sys­
tem has switched the ESC off . In th is case, you
can switch the ignition off and then on to
switch the ESC on again . The system is func­
tion ing complete ly when the indicator lamp
switches off.
If the
II indicator lamp illuminates , the ESC
was switched off with the
I ~ O FF I button .
Stabiliza tion contr ol (ESC /ABS ): Fa ult! See
o wne r's manual
If the DJ indicator lamp and the ti] ABS ind i­
cator lamp illum ina te and the driver message
appears, the ABS or electron ic different ia l loc k
is malfunctioning . This a lso interrupts the
ESC. The brakes still function with their nor­
mal power, but ABS is not active .
Drive to your author ized A udi dealer immedi­
ate ly to have the ma lfunction corrected.
For more information about the ESC
¢ page 197.
flit !t Safety systems
The fl (U SA models) ;fll (C anada models) in­
dicator light monitors the sa fety systems (e .g.
airbags, pretensioners) and illuminates for a
few seconds each time you switch the ignition on.
If the
fl (USA models) ! El (Canada mode ls)
indicato r light does not go o ut, or if it illumi-
nates while you are driving, or if it starts to ..,.

16 Instrum ent s and w arn ing /indic ato r light s
blink, then there is a ma lfunction somewhere
in the system.
If the light does not illuminate
when you switch the ignition on, this also
means there is a malfunction.
A WARNING
If you have a malfunction in the safety sys­
tems, contact your author ized Audi dealer
immediately. Otherw ise the safety sys­
tems may not work properly in an acci­
dent.
U) Tire pressure monitoring system -
telltale indicator lamp
Appl ies to vehicles: with tire pressure monitoring system
The warning/indicator light appears in the
event of a significant loss of tire pressure or if there is a malfunction.
The indicator light IE illuminates to check
the function when you switch on the ignition.
If the
IE symbol remains on or blinks after
you switch on the ignition, the re is a loss of
tire pressure or a system malfunction.
If there
is a system malfunction, see your authorized
Aud i dealer as soon as possible.
Detai led information on the tire pressure
mon itoring system can be fou nd in
¢page 266.
¢ Q Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left B or the right II
turn signal, the ind icator light blinks. When
you use the emergency flashers, both indica­ tor lights flas h.
If one of the turn s ignal light bulbs burn out,
the turn signa l wi ll blink tw ice as fast as nor­
mal.
This does not apply, however, in towing mode.
The indicator light does no t flash if a turn s ig­
nal is out on the trailer or the tow ing vehicle.
Addit ional info rmation on the turn sig nals
¢page 52.
~,1 ¢ Trailer turn signal assembly
Applies to vehicles: with towing hitch
The indicator light also blinks if the turn sig­
nal is operated when towing a trailer.
The ind icator light. bli nks when the turn
s ignal is used, if a trailer has been properly
con nected to the vehicle .
If one of the turn signa l bulbs on the trailer is
burned out or defective, the ind icator light
will not blink when you use the turn signals.
(D Tips
For vehicles with a factory installed towing
hitch or a trailer hitch that was installed
l ater according to factory spec ificat ions,
the trailer turn signal assembly is actuat­
ed.
,(t Safety belts
This warning/indicator light reminds you to
put on your safety belt.
The . warn ing/ indicator light illum inates
when the ignition is switched on to remind
the driver and (o n USA models only) any front
passenger to put on the safety be lt . Addit ion­
ally, an audib le warn ing tone w ill also sound .
For more Informat ion
¢ page 149, Safety
belt warning light.
o Malfunction Indicator Lamp (MIL )
The Ma lfunction Indicator Lamp (MIL) is part
of the On-Board Diagnos tic (OBD II) sys tem.
T he symbo l
(4 lights up when the ignition is
tu rned on and will turn off after the eng ine
has started and has settled at a constant idle
speed. This indicates that the MIL is working
properly.
The warning light ill uminates when the re is a
malfunction in the engine electronic system.
Contact your a uthorized Audi dea ler and have
the malfunction corrected. .,..

Instruments and warning/indicator lights 17
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
c::> page231.
F or mo re in forma tion
c::> page 26.
!§:D High beam
The II warning/indicator light illuminates
when the high beams are on o r whe n you use
the head light flasher. For mo re in format ion
about us ing the high beams, see
c:> page 52 .
CRUISE/"(-) Cruise control
The M;\1)~14 (USA models) Iii (Canada models)
war ning/ indica to r li ght illum inates when the
cru ise contro l is act ivated.
ABS/( @) Anti-lock brake system (ABS)
This warning/indicator light monitors the ABS
and th e electronic differ ential lock (EDL).
The
E (USA models) I ii] (Canada models)
warn ing/ indicato r light w ill come on for a few
seconds when the ig nition is swi tc h ed o n. The
light w ill go ou t aft er an au tomatic check se­
qu enc e is co mple ted .
There is a malfunction in the ABS when :
-The warni ng/ indicator lig ht d oes not ill umi­
nate whe n you switc h on the ignition .
- The warning/ indicator lig ht d oes not go out
after a few seconds .
- The warning/ ind icator lig ht ill uminates
wh ile driving.
The brake system will still respond even
without the assistance of the ABS system.
See your authorized Audi dealer as soon as
possible to restore full braking performance.
For more informat io n regarding the ABS
c:> page 19 7.
The ABS warn ing light and the brake warn­
ing light come on together. The ABS will not
work and you will notice a change in braking
re sponse and performance . Malfunction in the brake system
If t
he bra ke w arn in g ligh t c::> page 18 and
t he A BS warning ill uminate together there
may be a malfunction in the ABS, and the re
may also be a malfunction in the brake system
i tse lf
c:> A .
In the even t of a malfunction in the brake
system
the warning/ind icator light 1111
( U SA mode ls)/ . (Canada models) in the in­
strument cl uster flashes. By press ing the
jsET I
button , yo u can br ing up a d river message
which expla ins the malfunct io n in more de­
t a il. Please no te
c:> pag e 29.
Malfunction in the electronic differential
lock (EDL)
The EDL works together w ith the ABS . The
ABS wa rning lig ht w ill come on if there is a
malfu nction in the EDL sys tem
c:> page 197 .
See your author ized Audi dealer as soo n as
p oss ibl e.
_&. WARNING
- If the li!I (USA m ode ls)/ [I] (Canada
mo dels) warning light does not go ou t,
or if it comes on whi le dr iving , th e ABS
system is not wor king pro per ly . The vehi­
cle can then be sto pped on ly w it h the
standa rd b rakes (with out ABS). You w ill
not have the protect io n ABS p rov ides .
C ontact your au thorized A udi dealer as
s oon as p ossibl e.
- USA models: If the
1111 warning light
an d th e
m:SJ war ning light come on to­
g eth er, the rear wheel s co u ld loc k up
first under h ard br akin g. Rear w heel lock­
u p ca n caus e loss of vehicle control and
a n accident . H ave yo ur vehicle re pa ire d
imme diate ly by yo ur authorize d Au di
dea le r o r a qua lified wor kshop . Drive
slowly and avo id sudden, hard brake ap­
plications .
- Canada models: If the brake warning
light . and the ABS warning li ght
ii]
come on togethe r, the rear wheels could
l o ck up first und er hard braking. R ear
-

18 Instrum ent s and w arn ing /indic ato r light s
wheel lock- up can cause loss of vehicle
control and an acc ident. Have your vehi­
cle repaired immediately by your author­
ized Audi dea ler or a qualified workshop.
Drive slowly and avo id sudden, hard
brake applicat ions .
1:1.\.f(®) Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake.
W ith the parking brake app lied and the igni­
tion turned on, the. (USA models)/ . (Can­
ada models) warning/ind icator light illumi­
nates . After the ignition has been turned off,
the warning/ind icator light continues to i llu­
minate for about 30 seconds. If the parking
b rake is applied with the ignition turned off,
the warning/ind icator light illuminates for
about 30 seconds .
The warning/indicator light will go out when
the park ing brake is released.
If the war ning/ indicator light flas hes cont i nu­
ously
after appl ying the park ing b rake, brak­
ing fo rce is not sufficient to preve nt the vehi­
cle from roll ing uninten tionally. Please no te
the following:
- If the slope of the g round is too steep to
par k the vehicle , the add itiona l dr ive mes­
sage appea rs
Caution: Vehicl e parked to o
steep.
- In the event of a par king brake malfunct ion,
the ye llow
Ill symbol appears in the inst ru­
ment cluster d isplay and the dr iver message
Parking b rake malfunction! is displayed.
Have the malfunction repaired as soon as
possible by an authorized A udi dealer or any
other qualified workshop.
BRAKEl< CD> Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction.
The .. (USA mode ls) • (Canada models)
light ill uminates when the ign ition is turned on
. It goes out afte r the engine has been
started. This indicates that the brake warning
li ght is functioning properly.
If the br ake w arning light do es not light up
when the engine i s cranking , there ma y be a
malfunction in the elect rical sy stem . In thi s
ca se , conta ct an authorized Audi dealer .
If the brake sys tem warn ing/in dicator light
flashes, there is a b rake system ma lfunction.
By pressing the
! SET ! button, you can bring up
a driver message wh ich explains the malfunc ­
t ion in more detail
c> page 29.
If the ABS fai ls, the ABS warning/indicator
li ght
r4:B (USA models)/ 11] (Canada models)
flashes together with the brake system warn­
ing/indicator light
c> &. .
(USA mode ls): If the warning light .. and
the warning light
Ei] ill uminate together, im­
med iate ly contact your authorized Aud i dea ler
or qualified workshop to have all brake pads
inspected
c> page 33.
When the light comes on, an audible warning
s ignal is also given .
&_ WARNING
--= =
-USA models: If the .. warning light
and the
a warning light come on to­
gether, the rear whee ls could lock up
fi rst under hard braking. Rear wheel lock­
up can cause loss of vehicl e co ntrol and
an ac cident . Have yo ur vehicle repaired
immed iate ly by yo ur au thori zed Aud i
dealer o r a q ua lified workshop. Drive
slowly and avoid sud den, hard brake ap ­
plications .
-Canada models: If the brake warning
light . and the ABS warn ing light
[iJ
come on together, the rear wheels could
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
control and an accident . Have your vehi­
cle repaired immed iately by your author­
ized Audi dealer or a qualified workshop .
Dr ive s low ly and avoid s udden, hard
b rake applications.
~

20 Driver information display
Driver information
display
Introduction
General notes
The driver information display inside the in­
strument cluster provides you, the driver,
with much useful information.
Fig. 9 Instrument cluster: center display
Information from the driver information sys­
tem is shown in the display in the center of
the instrument cluster.
When you turn on the ignition and while you
are driving, some functions and vehicle com­
ponents are scanned for their operat ing sta­
tus. Malfunctions or required service proce­
dures are signaled audibly and shown by red
and yellow lighted symbols and reminders to
the driver in the display.
The driver is also shown information about ra­
dio and CD operation and directions for the
navigation system*. You can find additional
information on these subjects in the radio or
MMI* manual.
The illustr ations in the instrument panel dis­
play differ in some of the vehicles .
The driver information system provides the
following functions:
Sound system display
¢page20
Outside air temperature r:::;, page 21
Digital speedometer r:::;, page 21
Open door- and luggage com-llr:::;, page 21
partment warning
Service interval display
¢page 22 r:::;,page
27
Driver information r:::;,page 27
Speed warning r:::;,page93
Trip computer r:::;, page 23
Tire pressure monitoring sys-r:::;, page 266 1
tern*
Digital clock with date dis play
r:::;, page 12
Odometer and trip odometer ¢page 13
Selector lever position r:::;, page 123
¢page95
Adaptive cruise control* Energy flow display* ¢page 107
---,.--
r:=;,page 103
¢j) Tips
In the event of a malfunction either a red
or yellow icon appears in the display. Red
symbols indicate
Danger r:::;, page 28. Yel­
low symbols indicate a
Warning
¢page 31.
Sound system display
Fig. 10 Display: sound system
(0
"' .... 9 a:
~
If priority 1 or priority 2 faults are not shown
by the Auto Check Control, the name of the ra­
dio station you are tuned to or the frequency
and the reception range are shown in the up­
per area of the displ ay.
When the CD is in use , the title of the track
being played is shown. The CD changer dis­
plays the number of the current CD (CD
1 to
CD6).