2013 AUDI A6 ECO mode

Tires an d wheel s 245
you have stored. The system does not recog ­
nize the load condition of your vehicle.
The effectiveness of the ti re pressu re monitor­
ing sys tem* will be impaired if you store nor ­
mal load pressures but then operate the vehi ­
cle at its maximum load¢,& .
See the illustration ¢
fig. 191 for the location
of the label on dr iver's side B-pillar (co lor of
the actual labe l and exact location on the ve­
hicle wi ll vary slig htly) .
Note that the fo llowing tab le is accurate a t
the t ime o f go ing to press and is subject to
I Model / II Tire de signation
c h ange. In the event of discrepancies, the ti re
pressure label is located on the driver's side B­
pillar always takes precedence .
T he table below lists the recommended cold
ti re inflat ion pressures for the Audi mode l
covered by your Owner's Literat ure at the vehi­
cle's capacity weight and the t ire sizes instal­
l ed on the respective models as orig inal
equipment, or as a factory option.
Tire pressure
Engine normal load condition full load condition
A6: 2 .0 lit er
4 -cylinder
A6: 3.0 liter
-
225 /5 5 Rl 7 97H
All Season
245 /45 Rl8 l0OH XL
All Season
255 /40 Rl 9 l00H XL
All S eason
255 /40 Rl9 l0OY XL
High Performance
255 /35 R20 97Y XL
High Perfo rmance
225 /55 Rl 7 97H
All Season
6-cylinder 245 /45 Rl8 l00H XL
All Seaso n
255 /40 Rl9 l0OH XL
All Season
255 /40 Rl9100Y XL
High Performance
255 /35 R20 97V XL
High Performance
S6: 255 /40 Rl 9100YXL
4.0
liter High P erformance
a -cy lind er
255 /35 R20 97V XL
High Performance front
PSI
ll kPA
32 220
230
33 230
32 220
35 240
35 240
35 240
35 240
36 250
39 270
39 270
44 300
rear front rear
PSI
ll kPA PSI ll kPA PSI ll kPA
29 200 35 240 38 260
32 220 35 240
38 260
32 220 35 240
38 260
32 220 33 230 36 250
32 220 38 260 41 280
32 220 38 260 41 280
32 220 38 260 41 280
32 220 38 260 41 280
33 230 39 270 42 290
36 250 44 300 46 320
35 240 42 290 44 300
39 270 46 320 48 330
XL= reinfor ced or extra load tire . It may al so appear a s xl , EXTRA LOAD , or RF on the tire side-
'
I
l
J
•
I
wall. ..,.
•
•

24 6 T ire s and whee ls
The correct tire pressure for the spare wheel is
located on a label on the driver's side B-pillar.
Because tec hnical changes may be made to
vehicle equ ipment dur ing the model year, a l­
ways compare the tire size designation on the
tire pressure labe l on your vehicle with the
tires on your vehicle . Make sure that the tire
si ze information on the vehicle label is the
same as the si ze of the tires on the vehicle.
This is especially important if the vehicle be ­
longs to someone else or you bought the veh i­
cle with different rims/tires or you bought the
vehicle as a p reviously owned vehicle.
Remember, your safety and that of your pas­
sengers also depends on mak ing sure that
l oad limits are not exceeded. Vehicle load in­
cludes everybody and everything in and on the
ve hicl e. These load limits are technically refer­
red to as the vehicle's Gross Vehicle Weight
Rating ("GVWR") . The Gross Ax le Weight Rat­
ing ("GAWR") is the maximum load that can
be applied at each of the veh icle's two axles.
The Gross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance st icker labe l located on the
driver 's side B-p illar . The tire pressure label on
your Aud i lists the maximum combined
weight of all of the occupants and luggage or
o ther cargo that the vehicle can carry. For the
l ocation of the tire pressu re labe l
i=:> fig. 191.
A WARNING
Overloading a vehicle can cause loss of ve ­
hicle control, a cras h or other accident, se­
r ious personal injury, and even death.
- Carrying more weight than yo ur vehicle
was designed to carry will prevent the
vehicle from handling properly and in­
crease the risk of a loss of veh icle con­
trol.
- The brakes on a veh icle that has been
overloaded may not be able to stop the
vehicle within a safe distance.
- Tires on a vehicle that has been overload­
ed can fail suddenly causing loss of con­
trol and a crash . -
Always make sure that the total load be­
ing transported - including the weight of
a trailer hitch and the tongue we ight of a
loaded trailer -does not make the vehi­
cle heavier than the vehicle's G ross Vehi­
cle Weight Rating.
A WARNING
-- I ncorrect tire pressures and/or underin-
flation can lead to a serious or fatal acci­
dent.
- I nco rrect tire pressures and/or underin­
flation cause increased ti re wear and can
affec t the handling of the vehicle .
- I nco rrect tire pressures and/or underin­
flation can a lso lead to s udden t ire fail­
ure, including a blowou t and sudden de­
flation, ca using loss of veh icle cont ro l.
Checking tire pressure
The correct tire pressure for the tires original­
ly installed on your vehicle is listed on the tire
pressur e label located on driver's side 8-pil ­
lar .
The recommended tire pressures are on the
t ir e pressure label and in the table
i=:> page 244, Cold tire inflation pressure.This
means that the pressure m ust be checked and
adjusted when the t ire has not been dr iven for
more than a couple of miles (kilometers) at
low speeds during the previous three hours.
Air in the tires expands when the tire heats up as a result of inter nal frict ion as it flexes in
u se . T he t ire pressure is higher when the tire
has warmed up t han whe n it is "co ld. "
It is the inflation pressure in a "co ld" t ire that
counts . The refore, you should never let a ir out
of a wa rm tire to match "Cold t ire inflat ion
pressure" recomme ndat ions
i=:, page 244 . The
t ir es wo uld then be unde rinflated and co uld
fail suddenly .
T he t ire pressure label on your Audi lists the
recommended co ld tire inflation pressures at
m aximum cap acity for the new, or ig inal
equipmen t tires tha t were on your vehicle at ..,.

@ Tips
Where snow chains are mandatory oncer­
tain roads, this normally also applies to
veh icles with all-wheel dr ive.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of whee l bolts is matched to the
factory insta lled rims . If different rims are fit­
ted, the correct wheel bolts with the right
length and correctly shaped bolt heads must
be used. This ensures that wheels are f itted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same model
<=> page 287.
.&_ WARNING
Improperly tightened or maintained wheel
bolts can becom e loose caus ing loss of
cont ro l, a co llision and serious persona l in­
Jury .
- Always keep the wheel bolts and the
threads in the wheel hubs clea n so the
w heel bolts can t urn easily and be prop ­
erly t ightened .
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose while d riving if greased or
oi led, even if tightened to the specif ied
torque.
- Only use whee l bolts that belong to the
rim being installed .
- Never use different whee ls bolts on your
vehicle.
- Always maintain the co rrect tighten ing
torq ue for the wheel bo lts to reduce the
risk of a wheel loss . If the tightening tor­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cle is moving. If the tightening torque is
too high, the whee l bolts and threads
Tire s an d wheel s 257
can be damaged and the whee l can be­
come loose.
(D Note
The specified torque for the whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm) . Torq ue whee l bolts diago­
nally. After changing a whee l, the torq ue
must be checked as soon as possible with a
torque wrench -preferably by an author­
i zed Audi dealer or qualified workshop.
Low aspect ratio tires
You r Aud i is facto ry-equ ipped w it h low aspect
ra tio tires. These tires have been tho ro ughly
tested and been se lec ted spe cifically for you r
model for their superb perfo rmance, road fee l
and handling under a variety of driving condi­
tions. Ask your authorized Audi dealer for
more details .
T he low aspect ratio of these t ires is ind icated
by a numera l of
55 or le ss in the tire's s ize
designation. The numera l represents the ratio
of the t ire's sidewa ll height in relation to its
tread width expressed in percentage. Conven­
tiona l tires have a he ight/w idth rat io of 60 or
more .
The performance of low-aspect -ra tio tire s is
particularly sens it iv e to improper inflation
pressure. It is therefore important that low
aspect ratio t ires are inflated to the specified
pre ssure and that the inflation pressur e is
regularly che cked and maintain ed. Tire pre s­
s ures should be checked at least on ce a
m onth and alwa ys before a long trip
¢ page 246, Checking tire pressure .
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damage d mo re
easily by impact w ith potholes, curbs, g ull ies
or ridges on t he road, partic ularly if the tire is
u nderinflated.
Ill>-
•
•

264 What do I do now?
&_ WARNING
You or your passengers could be injured
while changing a wheel if yo u do n ot fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis­
tance
off the road. Turn off the engine,
turn the emergency flashers on and use other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- T o help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
ja ck, always fully set the parking b rake
and bloc k the whee l diagona lly opposite
the whee l being changed. When one
front whee l is lifted off the gro und, plac­
ing the Automat ic Transmiss ion in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced t ire i n the luggage com­
partment
¢ page 132.
Before chang ing the wheel, yo u m ust acti­
vate the jacking mode, so that the auto­ mat ic cont rols for the Adaptive Air S us­
pens ion* do not make it more difficult to
lift the vehicle with the jack
c> page 266.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
~page 266.
-
2. Remove the decorative wheel cov er* . For
mo re details see also ¢
page 265, Deco­
rative wheel covers
or c> page 265,
Wheels with wheel bolt caps.
3 . L oosen the wheel bolts¢ page 265.
4. Locate the proper mounting point for the
jack and alig n the jack below that point
¢ page 266 .
5.
Raise the car with the jack¢ page 266.
6. Remove the wheel with the flat tire and
then insta ll
the s pare ¢page 267.
7. Tighten all whee l bolts lightly.
8 . Lower the vehicle with the jack .
9. Use the wheel bolt wrench and firmly
t igh ten al l w heel bo lts¢ page 265.
10. Rep lace the decorat ive wh eel co ver* .
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI f u nction button > (Car )* sys­
tems
control button > Se rvicing & chec ks
> A ir susp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above
6 mph (1 0 km/h) .
&_ WARNING ,.__
Always read and follow all WARNINGS and
i nformat ion¢ &.
in Raising the vehicle on
page 266
and c> page 268.
After changing a wheel
A wheel change is not complete without the doing the following.
.,. Always store the vehicle tool kit, the jack *
and the rep laced tire in the luggage com­
partment
¢ page 132.
.,. Check t he ti re pressu re on the spare whee l
immed iate ly after mounting it .
.,. As soon as possib le, have the
tightening
torques
on all whee l bolts checked with a
t o rque wrenc h. The co rrect tighte ning tor ­
que is 90 ft lb (120 Nm).
.,. Have the flat tire
replaced as soon as possi­
b le.
(D Tips
- If you not ice th at the wheel bo lts a re
co rroded and difficult to turn while
changing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
ll-

@ Tips
The disc harged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charg ing the
battery, never connect the negative
ground cable to the battery negat ive post
because the ba ttery manager system must
be ab le to detect the battery's state of
charge. Always connect the negative
g round cab le to the negative ground pos t
of t he battery manager cont ro l unit.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described b elow!
Fi g. 21 4 Eng ine co mpar tment : connecto rs for jum p
s tar t cab les and ch arg er
F ig. 215 Jump start in g w ith t he ba ttery of a not her ve ·
hi cle :
@-booster battery, ®-disc harged ve hicle bat ­
te ry
The procedure described below fo r connecting
jumper cables is intended to provide a jump
start for your veh icle.
Vehicle with discharged battery :
• Turn off ligh ts and accessories, move leve r
of automatic t ransmission to N (Neutral) o r
P ( Par k) and set pa rking brake .
Emergenc y situ ation s 2 7 5
Connect POSI TIVE(+) to POSITIVE(+)
(red )
• Open the red cover on the positive te rminal
¢ fig. 214 .
1. Connect one end of the red positive cable
on the jump sta rt bolt
¢ fig. 215 (D (bolt
under the red cover = "positive") of the ve ­
hicle to be started @.
2 . Connect th e othe r end to the pos itive ter-
mi na l@ of the booster battery @.
Connect NEGATIVE( -) to NEGATIVE(-)
(black )
3. Connect one end of the black negative ca­ ble to the negat ive termi na l@ of the
booster b attery @.
4. Connect the othe r end to the jump start
pin @ (bo lts w ith hex head bolt = "nega ­
tive") of the vehicle to be started @.
Starting the engine • Sta rt the engine of the veh icle w ith the
booste r ba tte ry @ . Ru n the engine at a
moderate speed.
• Start engine wit h discha rged vehicle battery
@ in the usual manner.
• If the eng ine fails to sta rt, do not keep the
starter c ranking for longer than 10 seconds.
Wait for about 30 seco nds a nd the n try
aga in .
• With eng ine runni ng , remove j umper cab les
from both vehicles in the exact
reverse o r­
de r.
• Close the red cover on the posi tive term inal.
T he battery is v ented to th e outside to p rev ent
gases from en ter ing the veh icle in ter io r. Ma ke
s ur e th at the jumper clamps are well connec t­
ed with their meta l parts in full con ta ct w ith
the battery term inals.
,8. WARNING
To avoid se rious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable man ufac ­
ture r. If in doubt, call for road service .
- Ju mpe r cables m ust be long enough so
that the veh icles d o not touch.
-

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding yo ur warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
I f you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that:
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside North America .
Consumer Information 285
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, serv ice or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduct ion. Service manuals and lit­
erat ure are available to order from the Audi
T echnical Literature Ordering Center at:
www.audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a m inimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty
&
Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures,
in very dusty regions, when towing a trailer
very frequently, etc., some serv ice work
shou ld be pe rformed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air filter.
® For the sake of the environment
By regularly maintaining your veh icle, you
help make sure that emission standards
are maintained, thus min imiz ing adverse
effects on the environment .
Important considerations for you and
your vehicle
The increasing use of electronics, sophistica t­
ed fuel injection and emission contro l sys-
tems, and the genera lly increasing technica l ..,_
•
•

294 Index
------------------------------------
Data .... ....... ......... ... .... . 282
Start-Stop-System . . . . . . . . . . . . . . . . . . 76
start ing .. .. ................ ..... .. 71
Startingwithjumpercables .. .. ..... 274
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Engine compartment ........ .... ... . 227
C losing the hood .......... ... .... . 226
Opening the hood ................. 225
Safety instructions ........ .. .. .... . 225
Working in the engine compartment .. 225
Engine coolant .................... . 232
Adding coolant ............ ... .... . 233
Checking the engine coolant level .... . 232
Expansion tank ........... .. .. .. .. . 232
Malfunction symbol ....... .. .. .... .. 16
Radiator fan .............. ... .. .. . 234
Temperature gauge ........ ..... .. .. 11
Engine oil ... ................ ..... . 227
Adding .. .... ........... .... .... . 230
Additives . .. ............. .. .. .. ... 230
Changing .... ... .... .... .. .. .. .. . 231
Check ing the engine oil level .. .. .. .. . 230
I ndications and cond it ions requ iring ex-
tra checking .. ........... .. .. .... . 230
I ndicator light ........... .. .. .. .. .. 18
O il consumption .......... .... .... . 229
Oil grades . ................. ..... . 227
Oil level symbol .................... 21
Pressure malfunction ....... ... .. .. .. 17
Recommended oil check intervals ..... 230
Sensor defective . . . . . . . . . . . . . . . . . . . . 21
Specification and viscosity .. .. .. .. .. . 227
Engine sound .............. ... .... .. 98
E ng ine speed limitation ....... .. .. .. . . 21
Engine start-stop mode
refer to Star t-Stop-System ... .. .. .. .. 78
Engine start system (indicator lights) . ... 18
Environment Break-in period ......... .. .. .. .. .. . 199
Cata lytic converter ........ .. .. .. .. . 200
Disposing of your vehicle battery . ... . 239
Driving at high speeds .............. 202
Driving to minimize pollution and noise 201
Fuel . .. .. ............... .. .. .... . 222
Fuel economy ............ .... .... . 201
Leaks under your vehicle ... .. .. .. .. . 225
Lett ing the vehicle stand and warm up . 202
Proper disposal of drained brake fluid . 235 Proper disposal of d
rained engine cool-
ant ..... ..... .. .. .............. . 233
Proper disposal of drained eng ine
oil . . . . . . . . . . . . . . . . . . . . . . . . . 230,231
Recycling used engine oil ........ .... 230
Unleaded fuel .. .. ................ . 220
What should I do with an old battery? . 239
ESC (Electronic Stabilization Control) Warning/indicator lights ........ .. .. . 19
Event Data Recorder (EDR) ........ .. .. 192
Exhaust tail pipes .. .......... ...... . 214
Expansion tank .... ................ . 232
Exterior lighting . ... ............ .. .. . 41
Exterior mirrors Adjusting ..... .. .. ........ ...... .. 48
Dimming .. .. .. .. .. ..... ...... .. .. . 48
Heating ...... ... .. .............. .. 48
Exterior temperature display ...... .. .. . 23
F
Fastening
Booster seats . . . . . . . . . . . . . . . . . . . . . 180
Convertible child safety seats . . . . . . . . 178
Infant seats ... .. ............. .... 177
Floor mats . ..... .. ................ . 131
Foot pedals ..... .. ..... ........... . 131
For the sake of the environment Gasoline fumes and the environment .. 222
Reducing engine noise by early upshift-
ing ...... .... ... .. ................ 11
Refueling ... .. .. ....... ...... .. .. 222
Sav ing fuel by early upsh ifting . .. .. .. . 11
Four- zone automatic climate control . .. . 67
Front airbags
Description .... .. ................ . 149
How they work ... ................ . 155
Frontal coll is ions and the laws of phys ics 137
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . 50
Adjusting ... .. .. ....... ...... .. .. 128
Child restraints in the front seat ...... 147
Fuel Additives .. .... .. ............. .... 220
Blended gasoline .............. .... 220
Current consumption .............. .. 24
Economy messages (efficiency program) 26
Fuel filler flap emergency release ... .. 223