2013 AUDI A6 spare wheel

264 What do I do now?
&_ WARNING
You or your passengers could be injured
while changing a wheel if yo u do n ot fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis­
tance
off the road. Turn off the engine,
turn the emergency flashers on and use other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- T o help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
ja ck, always fully set the parking b rake
and bloc k the whee l diagona lly opposite
the whee l being changed. When one
front whee l is lifted off the gro und, plac­
ing the Automat ic Transmiss ion in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced t ire i n the luggage com­
partment
¢ page 132.
Before chang ing the wheel, yo u m ust acti­
vate the jacking mode, so that the auto­ mat ic cont rols for the Adaptive Air S us­
pens ion* do not make it more difficult to
lift the vehicle with the jack
c> page 266.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
~page 266.
-
2. Remove the decorative wheel cov er* . For
mo re details see also ¢
page 265, Deco­
rative wheel covers
or c> page 265,
Wheels with wheel bolt caps.
3 . L oosen the wheel bolts¢ page 265.
4. Locate the proper mounting point for the
jack and alig n the jack below that point
¢ page 266 .
5.
Raise the car with the jack¢ page 266.
6. Remove the wheel with the flat tire and
then insta ll
the s pare ¢page 267.
7. Tighten all whee l bolts lightly.
8 . Lower the vehicle with the jack .
9. Use the wheel bolt wrench and firmly
t igh ten al l w heel bo lts¢ page 265.
10. Rep lace the decorat ive wh eel co ver* .
11. Deactivate the vehicle jack mode* in the
MMI:
ICARI f u nction button > (Car )* sys­
tems
control button > Se rvicing & chec ks
> A ir susp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above
6 mph (1 0 km/h) .
&_ WARNING ,.__
Always read and follow all WARNINGS and
i nformat ion¢ &.
in Raising the vehicle on
page 266
and c> page 268.
After changing a wheel
A wheel change is not complete without the doing the following.
.,. Always store the vehicle tool kit, the jack *
and the rep laced tire in the luggage com­
partment
¢ page 132.
.,. Check t he ti re pressu re on the spare whee l
immed iate ly after mounting it .
.,. As soon as possib le, have the
tightening
torques
on all whee l bolts checked with a
t o rque wrenc h. The co rrect tighte ning tor ­
que is 90 ft lb (120 Nm).
.,. Have the flat tire
replaced as soon as possi­
b le.
(D Tips
- If you not ice th at the wheel bo lts a re
co rroded and difficult to turn while
changing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
ll-

-On hard, slippery surface (such as tiles)
use a rubbe r mat or similar to prevent
the jack from slipping .
- To he lp prevent injury to yourself and
your passengers:
- Do not raise the vehicle until yo u are
sure the jack is secu rely engaged.
- Passengers must not remain in the ve­
h icle when it is jac ked up.
- Make sure that passengers wa it in a
safe p lace away from the vehicle and
well away from the road and t raffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
r ai se the jack.
- Changes in temperatur e or load can af­
fect the height of the ve hicl e.
(D Note
Do not lift the ve hicle by the s ill. Position
the vehicle jack only at the des ignated
lift­
ing points on the sill. Othe rwis e, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­
mat ica lly at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles : wit h sill
Fig. 207 Sill: remov ing t he cover
.,. Pull the cover down to remove it c::> fig . 207.
.,. To install the cover again, inse rt it into the
retainers and then sw ing it upward unt il it
cl icks into place . T he cover m ust be flush
with the sill.
What do I d o now ? 267
@ Tips
Some models may also have a cover for the
rear vehicle lift po int.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing th e wheel.
Fi g. 208 Cha ngi ng a w heel: us ing th e screwd rive r ha n­
d le (w it h th e blade re m oved) to turn the bo lts
F ig . 209 Chang ing a whee l: a lig nment p in in sid e the
top hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing th e wheel
.,. Use the hexagonal socket in the screwd riv ­
er handle
to complete ly remove the top­
most wheel bolt and set it aside on a
clean
surface c::> fig. 208 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hol e
c::> fig. 209 .
.,. Then remove the other wheel bolts as de­
scribed above .
.,. Take
off the whee l leaving the alignment
pi n in the bolt hole
c::> (l).

268 What do I do no w?
P uttin g on the spare wheel
.. Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
L ike the rest .
.. Turn the jack handle cou nter -clockw ise to
lower the vehicle unt il the jac k is fully re­
leased.
.. Use the wheel bolt wrench to tighten all
wheel bolts firmly¢
page 265 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
(j) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel bo lts.
- When mounting tires with
unid irectional
tread design
make sure the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove al l dirt from these
surfaces before remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the tire .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optimum performance cha racter­
isti cs wit h regard to aquap lan ing, no ise and
wear .
- We recommend that you pay part icu la r at­
t ention to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new one and
have it insta lled on you r vehicle as soon as
possible to restore the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 251, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spar e imm e­
diately after install ation.
- Have th e whe el bolt tight ening torqu e
c hecked with a torque wrench as soon a s
pos sible by your author ized Audi de aler or
a q ualified service stat ion.
- With steel and allo y wheel r im s, the wheel
bolt s ar e cor re ctl y tightened at a torque of
90 ft lb (1 20 Nm ).
- If you noti ce th at the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be repl aced before you
check the t ightening torque. .,..

280 General information
General information
Explanation of
technical data
Some of the technical data listed in this man ­
ual requires further explanation .
The technical data for your vehicle is listed in
the charts starting on
r:::> page 282. This sec­
tion provides general information, notes and restrictions which apply to this data.
Vehicle identification
The key data is given on the vehicle identifica­
tion number (VIN) plate and the vehicle data
sticker .
Fig. 223 Veh icle Ide ntificat io n Number (VlN) p late: lo ­
cation on driver 's s ide das h panel
Fig. 224 The vehicle identi fication label -inside the
luggage co mpa rtmen t
The Vehicle Identification Number (VIN)
is located on the driver's side so that it is visi­
ble from the outside through the windshield
r:::> fig . 223. You can also display the Vehicle
Identification Number of your vehicle in the
MMI. Select: Function button
I CAR ! > (Car) *
systems
> VIN number . The
vehicle identification label
is located in the luggage compartment in the
spare wheel well.
The label¢
fig. 224 shows the follow ing vehi­
cle data :
(D Product ion control No .
@ Vehicle identification No.
® Type code number
@ Type designation/engine output in Kilo-
watts
® Engine and transmission code letter
@ Paint No./Interior
(f) Optional equipment No.'s
Vehicle data 2 to 7 are also found in your War­
ranty
& Maintenance booklet.
The safety compliance sticker
is your assurance that your new vehicle com­
plies with all applicable Federal Motor Vehicle
Safety Standards which were in effect at the
t ime the vehicle was manufactured . You can
find this sticker on the left door jamb .
It
shows the month and year of production and
the vehicle ident ification number of yo ur vehi ­
cle (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label
is located on the lock carrier.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
left door jamb.
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus fu ll fuel tank,
oi l and coo lant, plus maximum load, which in­
cludes passenger weight (150 lbs/68 kg per
Ill>

Seat adjustment Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Driver's seat . ... ...... ... .. .. .. .. .. 50
Front passenger's seat . . . . . . . . . . . . . . . 51
Front seats . . . . . . . . . . . . . . . . . . . . . . . . SO
H ead restraints
Safety guide lines . . . . . . . . . . . . .
. . 53, 130
so .... ..... .. .. .. .. ..
Seat belts
WhyYOU M USTwearthem . .. .. .. .. . 136
Sea t hea ting/vent ilation (automatic cli-
mate con trol) . . . . . . . . . . . . . . . . . . . . . . . 68
Seat hea ting (climate control) . . . . . . . . . . 66
Seating position Driver ... .. .. .. ........... .. .. .. .
Front passenger .......... .... .. .. .
H ow to adjust the front seats . .. . ... .
Incorrect seat position ......... ... . . 127
128
128
130
Occupants .. .... .. .... ... .. .. .. .. . 127
R ear passengers . . . . . . . . . . . . . . . . . . . 129
Seat memo ry . . . . . . . . . . . . . . . . . . . . . . . 54
Seats Comfo rt seat side view . . . . . . . . . . . . . . 55
Seat symmetry . . . . . . . . . . . . . . . . . . . . . 55
Seats (number) . ........... .. .. .. ... 136
Select ive unlock feature ..... .. .. .. .. .. 34
Selector lever . .... ..... ... .. .. .. ... 105
Sel ecto r leve r eme rgency r elease . .. .. . 11 1
Service and disposal Safety belt pretens ioner . . . . . . . . . . . . 143
Service in terval disp lay ... ... .. .. .. .. .. 27
Shift buttons ................. .... .. 109
Ship (transporting your veh icle) . .. .. .. . 278
Side airbags
D escr ipt io n . .. ... ..... ... .. .. .. ... 165
How t hey work . ... .... ... .. .. .. ... 166
side assist . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Ad justing the brigh tness ... .. .. .. .. .. 96
Sensor r ange
Side assist
............ .... .. .... 9 5
Activating and deactivating . . . . . . . . . . . 96
C lea ning senso rs ............ .. .... 211
Side curtain airbags ........ .. .. .. .. . 168
Descr ipt ion . ............. .... .. .. .
168
H ow they work ... .. ...... .. .. .. .. . 169
Safety instructions ........... .... . . 169
Side ma rker lights . ..... ... .. .. .. .. .. 41
Ski s ack 63
Index 299
Sliding/tilting s unroo f
Emergency closing . .. ... .... ... .. .. . 40
Open ing and closing . .. ..... ... .. .. . 40
Snow cha ins .. .. .. .... ........... .. 256
Socket . .. .. .. .. .. .. . ... ...... ... .. . 56
Sources of information abo ut child re-
straints and their use .. ... .... ... .. . .
Spa ce-savi ng spa re tire ........... ... .
Spare tire ... .. .. .. .... ............ . 189
2 62
262
Speed limi ter ... .... . ... ...... ... .. . 30
Speedometer ..... .. ................ 27
Speed rat ing letter code .............. 252
Speed warning system ........... .. .. .
Sport d iffe rential .................. . . 7
9
98
Ind icator lig ht ... .. . .. .... .... .. .. . 22
Star button . . . . . . . . . . . . . . . . . . . . . . . . . 24
Star t-Stop-System . . . . . . . . . . . . . . . . . . . 76
En gine does not swi tched off .... ..... 78
E ngine sta rts a utomat ica lly .. ... .. .. . 78
In dicator lights .... . .. ..... ... .. .. . 77
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 79
Starting/stopp ing the engine .... .. .. . 77
switching off/on . . . . . . . . . . . . . . . . . . . . 78
START ENG INE STOP button ... ... .. .. . 71
Starting from rest .. .. .. .. ...... .... . . 75
Starting off w ith a trailer ......... .... . 76
St arti ng the engine ............. .... . 71
Steering El ectr ica lly adjus table steering wheel .. 70
Manually adjustable stee ring wheel .... 70
also refer to Electro-mecha nica l powe r
ass ist .. .... .. .... ... .......... .. 19 6
Steering wheel Easy entry feature . . . . . . . . . . . . . . . . . . 71
Ind icator light . .. .. ..... ........... 18
Stee ring w heel heat ing ......... .. .. . 69
Steering wheel column Adjust ing electrically . . . . . . . . . . . . . . . . 70
Adjust ing ma nually . . . . . . . . . . . . . . . . . 70
Steering wheel with tiptronic ... ... .. .. 109
Steps for determin ing correct load limi t . 24 9
Stopping the eng ine ............. .... . 73
Storage
. . .. .. .. .... . ... ...... ... .. . 57
S tronic tra nsmission
L aunc h Control Prog ram ........ .. .. 110
S tronic ® ... .. .. .. ................. 105
•
•