2013 AUDI A5 COUPE bolt pattern

-Do not raise the vehicle until yo u are
sure the jack is securely engaged.
- Passenge rs must not remai n in the
ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then contin ue to
ra ise the jack.
CD Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
Taking the wheel off /installing the spare
tire
Follow these instructions step-by-step for
changing the wheel.
Fi g. 189 Changing a wheel: using the screwdrive r han ­
dle (with the blade removed) to turn the bolts
Fig . 1 90 Changing a wheel: alignm en t pin ins ide t he
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
What do I d o now ? 257
Removing the wheel
.,. Remove the topmost whee l bolt completely
with the
he xagonal so ck et in the screwdriv ­
er handle (vehicle tool kit)
o fig. 189 and
set it aside on a
clean surface .
.,. Screw the threaded end of the
alignment
pin from the tool kit hand-t ight into the
empty bolt hole
o fig. 190.
.,. Then remove the other wheel bolts as de ­
scribed above .
.,. Take
off the whee l leav ing the a lignment
pi n in the bolt hole
o(D .
Putting on the inflat able spar e tire
.,. Push the spare tire over the alignment p in.
.,. Screw on the wheel bo lts and tighten them
slightly us ing the hexagonal socket .
• Remove the a lignment pin and inse rt and
tighten the rema ining wheel bolt slightly
like the res t.
.,. Turn the jack hand le co unter -clockwise to
lower the veh icle until the jack is fully re ­
leased .
.,. Use the wheel bolt wrench to tighten all
wheel bo lts f irm ly
o page 255 . Tighten
them
in a crisscross pattern, from one bolt
to the (approximately) opposite one, to keep
the wheel centered .
• Perfo rm the steps required afte r changing
the wheel
o page 254, After changing a
wheel.
T he hexagonal socket makes it easie r to re­
move th e wheel bo lts from the rim. Care
sho uld be taken when remov ing the reversib le
blade .
CD Note
When removi ng or insta lling the whee l,
the r im cou ld hit the bra ke roto r and dam­
age the roto r. Work carefu lly and have a
second person to help you .
(l} Tips
-When mount ing tires w ith unidir ectional
tread de sign
make sure the tread pat ­
tern is pointed the right way
o page258. II>-

258 What do I do now?
-The w heel bolt s should be clea n and easy
to tu rn. Check for dirt and corrosion on
t h e mat ing s urfaces o f both the whee l
and the h ub. Remove a ll dirt from these
su rfaces befor e remo unt ing the wheel.
- Do no t use the hexagona l socket in the
screwdriver handle to l oosen o r ti gh ten
t h e wheel bo lts .
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire w it h a t read patte rn
in te nded for use in a specific direction, p lease
n ote t he follow ing:
- The direction of rotation is marked by an
ar­
row on the side of the tire .
-If the spare t ire has to be installed in the in­
correct d irection, use the spare tire only
temporarily si nce the t ire will not be able to
achieve its optimum perfo rma nce character ­
ist ics w ith r ega rd to aquaplani ng, noise and
wea r.
- We recommend tha t you pay particular at ­
tent io n to this fact du ring wet weathe r and
t h at you a djust your spee d to matc h roa d
condition s.
- Re place the fla t tire w ith a n ew on e and
h av e it installed o n your ve hicle as soon as
p ossib le to res tore the ha nd ling ad vantages
o f a un idirect ional t ire.
Notes on wheel changing
Please rea d the information c::> page 242, New
tires and replacing tires and wheels
if you are
go ing t o use a spare t ire which is different
from the tires on your ve hicle.
Afte r you change a tire :
-Check the tire pressure on the spare imme­
diately after installation. -
Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lbs. (120 Nm).
- If you notice that the wheel bolts are cor ·
roded and difficult to turn while chang ing
a tire , they should be replaced before you
check the tightening torque .
- Replace the flat tire w ith a new one and
have it installed on your vehicle as soon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re·
duced speeds.
A WARNING ..__ -
- If you are going to equ ip your ve hicle
wit h tir es o r rims which differ from th ose
which w ere fac tory i nstalled, then be
s ure to read the information
c::> pag e 242 ,
N ew t ires and repl acin g tires and
wheels.
- Always make sure the dam age d wheel o r
eve n a flat tire and t he jack and to ol kit
a re p roperly secu red in the lugg age com­
p art ment and are no t loose in the pas ­
sen ger compartment.
- In an a cci dent or sudde n maneuver they
co uld fly forwa rd, in juring a nyone in the
veh icle.
- Always s to re damage d whee l, jack an d
too ls sec urely in the l ugga ge com pa rt­
ment. Othe rwise, in a n accide nt or s ud­
den maneuver they co uld f ly forwa rd,
causing inj ury to passe ngers in the ve hi­
cle .
(I) Note
Do not use comme rcially ava ilab le tire
sea lants. Ot herwise , th e e lectr ica l comp o­
nents of the tire pressu re monitoring sys­
tem* w ill no longe r work pr oper ly and th e
se nso r fo r th e tire pressure moni tor ing
syst em* will have to be repla ced by a
qu alifie d w ork s hop .