2013 AUDI A5 COUPE light

@ Tips
-Pressing the button~ several times
consecutively can trigger the overload protection. The sun shade can only be ex­
tended/retracted again after a brief wa it­
i ng per iod.
- The rear window sun shade only func­
tions when the veh icle inter ior is warmer
than 14°F (-10°C).
Wiper and washer system
Switching the windshield wipers on
Fi g. 45 Windshield wiper lever
Move the windshield wiper lever to the corre ­
spond ing position:
@ -Windshie ld w iper
off
CD -Interval mode. To extend/shorten the
wiper intervals, move the switch @to the
l eft/right. I n veh icles with a rain sensor* the
wipers turn on in the ra in once the vehicle
speed exceeds approximate ly 2 mph (4 km/h).
The highe r the sensitivity of the rain sensor* is
set (switch @to the right), the earlier the
windshie ld w ipers react to moistu re on the
windshie ld. In some models, you can switch
rain sensor mode
off and switch intermittent
mode on in the MMI*. Select:
ICAR I funct ion
button
> Car Systems contro l button > Driver
as sis t > Rain s en sor .
In inte rmittent mode '
you can adjust the interval time using the @
sw itch.
@ -Slow wip ing
® -Fast wiping
Clear vi sion 49
@ -Single wipe
® -C lean the w indshie ld. To elim ina te wate r
drople ts, the windsh ield w iper pe rform s one
afterw ipe operation after severa l se conds
whi le dr iving. You can sw itch this f unction
off
by moving the leve r to positio n® within 10
seconds of the afterwipe operat ion . The after ­
wipe function is reactivated the next t ime the
ignition is switched on .
Cleaning the headlights* . The headlight wash­
er system * operates only when the headlights
are o n. If you move the lever to position @,
the headlights are washed in intervals.
A WARNING
- The rain senso r is only intended to assist
the dr iver. The d river is st ill responsib le
for manually switc hing the wipers on ac­
cording to the vi sibility cond itions.
- The windsh ield may not b e treated with
wate r-repell ing windsh ield coating
agen ts. Un fa vo rable cond iti ons, s uch as
we tnes s, d arkn ess, low sun, can result in
increased g lare. Wiper blade c hatter is
a lso possib le .
- P rope rly f unct io ni ng win dsh ield wipe r
b lades are re quired for a clear view and
safe driving
~ page 50, Replacing
windshield wiper blades.
(D Note
- I n the case of frost, check whethe r the
w indshield wiper blades are frozen to
the winds hield. Switchi ng on the wind­
shield wipers can damage the wiper
blades!
- Pr ior to using a car wash, the windshield
w iper system must be sw itched
off ( lever
in posit ion @). T his he lps to prevent un­
intentional switching on and damage to
t he windsh ield wiper system.
@ Tips
- The windshiel d w ipers are switched off
when the ig nition is tu rned off. Act ivate
t he windsh ield wipers after the ignition

50 Clear vis ion
is sw itched b ack on by mov ing the
winds hield wiper lever to any position .
- Worn or dirty windshie ld wiper b lades
r es ult in streaking. This can affect the
rain sensor* function. Check your wind­
shield wiper b lades regularly.
- The was her fluid nozzles of the wind­
s h ield washer system are heated at low
temperatures when t he ignit ion is on.
- When stopping temporarily, (e .g . at a
traff ic light) the set speed of the wind­
shield wipers is automatically red uced by
one speed.
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
F ig . 4 6 Remov ing windshie ld w iper blade
Wiper service position /blade replacement
position
.. Swi tch the w indshield wiper s off (posi tion
@ ¢page 49, fig. 45).
.. Se lect:
ICARI f u nct ion button > Wind shield
wipers
> Ser vice po sition > on . Or
.. Se lect:
I CARI f u nction button > Car sy stem s
control button > Servicing & checks > Wiper
service position > On .
The windsh ield wipers
move into the service position .
Removing the wip er blade
.. Lift the w indshield wiper arm up from the
windshield.
.. Press the locking knob(!)¢ fig. 46 on the
wiper blade. Hold the wiper blade firm ly.
.. Remove the w iper blade in the direction of
the arrow .
Attaching the wipe r blade
.. Inst all the new wiper blade in t he reta iner
on the wiper a rm @ unt il you hear it click in ­
to p lace on the wiper arm.
.. Place the wiper arm back on the winds hield.
.. To bring the w ipers back into the original
position, press the windshield wiper lever .
Or
.. Select:
!CAR I function button> Windshield
wip ers
> Service po sition > off . Or
.. Select:
!CAR I function b utton> Car sy stem s
cont ro l butto n > Servicing & che cks > Wip er
s ervi ce po sition
> Off .
A WARNING
=
-If the windshie ld wipers smea r the wind-
shie ld, clean the wiper b lades with wind­
shie ld washer fluid. If the wiper blades
are ext remely dirty, you can a lso clean
them with a soft sponge o r cloth.
- For your safety, you shou ld replace the
wiper blades once or twice a year. See
your author ized Audi dealer for replace­
men t blad es.
(D Note
- The windshie ld w iper blades m ust only
be replaced when in the service pos ition!
Otherw ise, you risk damag ing the pa int
on t he hood o r the windsh ie ld w iper mo­
to r.
- Yo u should not move your veh icle or
press the windsh ield wiper lever when
the wipe r arms are folded away from the
w indshield. The winds hield wipers wo uld
move back into their or iginal position
and co uld damage the hoo d and wind ­
shield.
- T o help preven t damage to the w iper sys­
t em, always loosen blades w hich are fro ­
zen to the windshield before operating
w ipers .
- To help prevent damage to wiper b lades,
do not use gasoline, kerosene, paint
thinne r, or other solvents on or near the
w iper blades.

Seats and storage
General recommen­
dations
Why is your seat adjustment so important?
The safety belts and the airbag system can
only provide maximum protection if the front
seats are correctly adjusted.
There are various ways of adjusting the front
seats to provide safe and comfortable support
for the driver and the front passenger. Adjust
your seat properly so that :
- you can easily and quick ly reach all the
switches and controls in the instrument
panel
- your body is properly supported thus reduc­ ing physical stress and fatigue
- the safety belts and airbag system can offe r
maximum protection
¢ page 142.
In the following sections, you will see exactly
how you can best adjust your seats .
There are special regulations and instructions
for installing a child safety seat on the front passenger's seat. Always follow the informa­
tion regard ing child safety provided in
¢ page 166, Child Safety.
.&_ WARNING
-
Refer to ¢ page 124, Driving Safely for
important information, tips, suggestions
and warnings that you should read and fol­
low for your own safety and the safety of
your passengers.
.&_ WARNING
Incorrect seating position of the driver and
all other passengers can result in serious
personal injury.
- Always keep your feet on the floor when
the vehicle is in motion -never put your
feet on top of the instrument panel, out of the w indow or on top of the seat cush­
ion. This app lies especially to the passen-
S eat s an d sto rage 53
gers . If your seating position is incorrect,
you increase the risk of injury in the case
of sudden braking or an accident . If the
airbag inflates and the seating position
is incorrect, this cou ld result in pe rsonal
in jury or even death.
- It is important for both the driver and front passenger to keep a distance of at least 10 inches (25 cm) between them­
selves and the steering wheel and/or in­
strumen t panel. If you're s itting any
closer than th is, the airbag system can ­
not protect you properly. In addition, the
front seats and head restraints m ust be
adj usted to your body height so that they
can give you max imum protect ion.
- Always try to keep as much distance as
possible between yourself and the steer­
ing wheel or instrument panel.
- Do not adjust the driver's or front pas­ senger's seat whi le the vehicle is moving.
Your seat may move unexpectedly, caus­
ing sudden loss of veh icle control and
pe rsonal injury. If you adjust you r seat
while the veh icle is moving, you are ou t
of posit ion.
Driver's seat
The correct seat position is important for safe
and relaxed driving .
We recommend that you adjust the dr iver's
seat in the follow ing manner:
.., Adjust the seat in fore and aft direction so
that you can easily push the pedals to the
floor wh ile keeping your knees slightly bent
¢ .&, in Why is your seat adjustment so im ­
portant? on page 53.
"" Adjust the seatback so that when you sit
w ith your back against the seatback , you can
s ti ll grasp the top of t he steering wheel.
... App lies to vehicles with adjustable head re­
straints: Adjust the head restraint so the up­
per edge is as even as possible wit h the top
of your head. If that is not possib le, try to
adjust the head restraint so that it is as .,.

58 Seats and storage
they are stored, these seat profiles can be
se lected at any time .
I n addition to the driver's seat settings, you
can also stor e and access the exterior mir ror
adj ustment settings* using the remote con­
trol key or memory button .
Remote control key
Applies to vehicles: with seat memo ry
To assign the driver 's seat settings to the re­
mote control key when locking the vehicle, the
function must be activated in the radio or
MMI*
.. Se lect :
ICARI function button > Seat adjust­
ment > Driver's seat > Remote control key
>
on.Or
> Select: ICARI function button> Car systems
control button > Vehicle settings > Seats>
Driver's seat> Remote control key> On .
@ Tips
If you do not want another d river's set­
tings to be assigned to the remote key,
switch off the memory function using the
radio or MMI* or the
ION/OFF I button
qpage58.
Memory buttons
Applies to vehicles: with seat memo ry
F ig. 57 Driver's doo r: memory function buttons
The memory buttons are located in the driv­
e r's door.
Switching the memory function on/off
.. Press the !ON/O FF I button to switch the
memory function on/off. The word
OFF
lights up when the memo ry function is
switched off . Seat profiles are not stored .
Storing a seat profile
.. Press the ISETI button. When the word SET
lights up, the memory is ready to store set­
tings .
.. Press a memory button
dil or~) briefly. A
tone conf irms that the sett ings were stored.
Accessing a seat profile
.. If the driver's door is open, press a memory
but ton.
.. If the driver's door is closed, press and hold
the memory button until the seat adjust­ ment is complete.
A WARNING
- For safety reasons, the seat setting can
only be recalled when the vehicle is sta­
tionary -otherwise you risk having an ac­
cident.
- In an emergency the recall procedure ca n
be cancelled by pressing the
ION/OF F!
sw itch or by tapping the memory but­
tons.
Ashtray
Fig. 58 Center co nsole: ashtray
Opening/closing
.. To open the ashtray, slide the cover up
qfig. 58.
.. To close the ashtray, press down on the cov-
er. ..,.

Emptying the ashtray
• To remove the insert , slide the latch to the
right
r:!) fig. 58 -arrow-.
• To install the insert , press it down into the
mount.
A WARNING
Never put waste paper in the ashtray . Hot
ashes or other hot objects in the ashtray
could set waste paper on fire.
Cigarette Lighter
Fig . 59 Fron t cen te r con so le: cigarette ligh ter
• Press the cigarette lighter in.
• Remove the cigarette lighter when it pops
out.
A WARNING
The cigarette lighter only works when the ign ition is switched on. Incorrect usage
can lead to serious injuries or burns. For
this reason, children should never be left
unattended in the vehicle because this in­
creases the risk of injury .
(D Note
The cigarette lighter can be damaged if
you connect electrical accessories to it .
Storage
General overview
A WARNING
-Always remove objects from the instru­
ment panel. Any items not put away
Seats and storage 59
could slide around inside the vehicle
while driving or when accelerat ing or
when applying the brakes or when driv­
ing around a corner .
- When you are dr iving make sure that
anyth ing you may have placed in the cen­
ter conso le or other storage locations
cannot fall out into the footwells . In case
of sudden braking you would not be able
to brake, dep ress the clutch or acce le r­
ate.
- Any pieces of clothing that you have
hung up must not interfere wit h the driv­
er's view. The coat hooks are designed
only for lightweight clothing. Never hang
any clothing with hard, pointed or heavy
objects in the pockets on the coat hooks.
During sudden braking or in an accident -
especially if the a irbag is deployed -
these objects could injure any passen ­
ge rs in side the vehicle.
Cupholder
Fig. 60 Cen ter c on sol e: fr ont cupholde r
Fig. 61 Rea r armrest: rear cupho ld er
Opening rear cupholders
• To open the cupholder, press on the symbo l
'i@ ¢ fig. 61 . ....

cannot fall out into the footwells. In case
of sudden braking you would not be able
to brake or accelerate.
- Any articles of clothing that you have
hung up must not interfere with the driv­
er's v iew. The coat hooks are designed
only for lightweight clothing. Never hang any clothing w ith hard, pointed or heavy
objects in the pockets on the coat hooks.
During sudden braking or in an accident -
especially if the airbag is deployed -
these objects cou ld injure any passen­
gers inside the vehicle .
- To reduce the r isk of personal injury in an
accident or sudden stop, always keep the
glove compartment closed while driving.
- Read and fo llow all WARN INGS
~ page 161, Important safety instruc­
tions on the side airbag system.
- Hang clothes in such a way that they do
not impair the driver's vision .
- T he coat hooks must only be used for
lightweight clothing. Do not leave any
heavy or sharp edged objects in the pock­
ets which may interfere with the side cur­
tain airbag deployment and can cause personal injury in a crash.
- Do not use coat hangers for hanging clothing on the coat hooks as this can in­
terfere with proper deployment of the
side curtain airbags in an accident.
- Do not hang heavy objects on the coat
hooks, as they could cause personal in­
jury in a sudde n stop.
- Always keep the compartment above the
rearview mirror closed while driving to
reduce the risk of injury in the event of
sudden braking maneuvers or a col lision.
(D Note
Objects located on the rear shelf that rub
aga inst the rear w indow cou ld damage the
heating wires for t he rear w indow defog­
ger.
S ea ts a nd s to rage 61
@ Tips
-A vent slot is located between the shelf
and the rear w indow . Do not block the
vent with any items you may place on the
rear window she lf.
- Do not place bu lky items on the rear win­
dow shelf as they could restrict or block
the driver's vision in the rear view m irror.
Roof rack
Description and mounting location s
Additional cargo can be carried with a roof
luggage rack.
F ig . 63 Roof rack attachmen t po ints
.,. Always read and follow the i nstructions pro­
vided by the roof rack manufacturer when
installing the roof rack system.
If luggage or cargo is to be carried on the
roof, you must observe the fo llowing:
- Yo ur vehicle has aerodynam ic rai n gutters
mo lded into the roof. This is why conven­
tional roof luggage racks cannot be used.
We recommend using roof racks from the
Audi orig inal accessories program.
- On ly use roof racks approved for your vehi­
cle. These approved roof racks are the bas is
for a complete roof rack system. Addit ional
attachments or carrier systems are needed
to transport luggage and sports equipment.
We recommend using roof racks from the
Audi orig inal accessories program .
- When installing the roof rack, make sure it
is only mounted on the designated locations
on the roof
Q fig . 63 . ..,.

66 Seat s a nd s tor ag e
8_ WARNING
-
- The ski sack is intended only for the
transportation of skis and other light ob ­
jects . To reduce the risk of serious per­
sonal injury, never transport heavy or
pointed objects in the ski sack.
- When brak ing rapidly or during an acci­
dent, the load could be displaced and
ca use injury to occupants.
- Sharp edges on the load must be covered
for protect ion. Always fasten the belt
t ightly around the sack and its contents
¢ fig. 70.
-For safety reasons, do not transport
more than two pairs of skis in the ski
sack .
- You must sec ure the ski sac k with the
st rap after loading.
- Make su re a ll objects that you are t rans­
porting in the pass-through are secured.
Otherwise they cou ld slide around during
sudden braking maneuvers and cause in­
jury.
(D Tips
- Never stow the sk i sack away when it is
still wet or damp (for examp le, snow
melting from skis). Allow it to dry com­
plete ly before stowing it away.
- When transporting skis or snowboards, tighten the securing strap between the bindings.
- Position skis in the ski sack wit h the
pointed ends facing the front and ski
po les with the pointed ends facing the
rear.
- You can lock or un lock the pass-through
u sing the mechanical key. This prevents
any access to the luggage compartment
from the vehicle interior .
Parcel shelf
The parcel shelf behind the rear seatback can
be used to car ry light items of cloth ing .
8_ WARNING
No heavy or hard objects should be p laced
on the parcel shelf. They are a hazard to
the veh icle occupants during s udden brak­
i ng . The is a risk of injury .
(D Note
Please make sure that the heating w ires
for the rear window defogger are not dam ­
age by abrasive objects .
(D Tips
To ensure problem-free ven tilation , the
vent ilation slots between the rear window
and the pa rcel she lf must not be covered .

68 Warm and cold
Operation
We recommend pressing the IAUTOI button and setting the temperature to 72 °F (22 °C) .
Fig. 71 Automat ic cl imate control system: control
Fig. 72 3-zo ne de luxe automatic cl imate contro l' : contro ls
Press the buttons to turn the funct ions on or
off. Use the d ials to adjust the temperature,
the blower speed and the a ir distribution . The
LED in a button will light up when the func­
tion is switched on. The settings are disp layed
for a few seconds in the radio or MMI* display .
In vehicles with a 3 -zone deluxe automat ic cl i­
mate control systems*, the dr iver and front
passenger side can be adjusted separately .
The settings are also displayed in the climate
control sys tem display.
IOFF I Switching the climate control
system on/off
The IOFFI button switches the climate control
sys tem on or off . It also switches on when you press the knob. Airflow from outside
is
blocked when the climate control system is
switched off .
IAC I Switching cooling mode on/off
The air is not coo led and humidity is not re­
moved when cooling mode is switched off .
This can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is below ze ro .
1- 1 Switching recirculation mode on/off
In recircu lation mode, the air inside the vehi­
cle is c irculated and filtered. This prevents the
unfiltered air outside the vehicle from enter­
ing the vehicle interior . We recommend