2013 Alfa Romeo 4C ESP

IMPORTANT
12) Punctures caused by foreignbodies can be repaired if the
damage does not exceed 4 mm on
the tread and on the shoulder of
the tyre. Do not use the repair
kit if the tyre was damaged as a
result of being used when
underinflated.
IMPORTANT
2) Dispose of the bottle and thesealant properly. Dispose of the
components in compliance with
national and local regulations.
CHANGING A BULB
13)101) 102) 103)
GENERAL
INSTRUCTIONS
❒Before changing a bulb check the
contacts for oxidation;
❒ replace blown bulbs with others of
the same type and power;
❒ after replacing a headlight bulb,
always check its alignment;
❒ when a light is not working, check
that the corresponding fuse is intact
before changing the bulb. For the
location of fuses, refer to the
paragraph “If a fuse blows” in this
chapter.
IMPORTANT
13) Halogen bulbs must be handled
by holding the metallic part only.
Touching the transparent part
of the bulb with your fingers may
reduce the intensity of the
emitted light and even reduce the
lifespan of the bulb. In the case
of accidental contact, rub the
lamp with a cloth and spirit and
leave to dry.
WARNING
101) Modifications or repairs to theelectric system that are not
carried out properly or do not take
the system technical
specifications into account can
cause malfunctions leading to the
risk of fire.
102) Halogen bulbs contain pressurised gas; in the case of
breakage they may burst.
118
IN AN EMERGENCY
24-9-2013 11:50 Pagina 118

REPLACING
EXTERIOR BULBSFRONT LIGHT CLUSTERS
These contain the bulbs for the side
lights/daytime running lights (DRL),
dipped beam headlights, main beam
headlights and direction indicators. The
bulbs are arranged as follows fig. 87:ASide lights/daytime running lightsBDipped/main beam headlightsCDirection indicators
To replace the bulbs for the dipped and
main beam headlights and for the
direction indicators open the
corresponding protective flaps on the
inner wheel arch fig. 88 that can be
located by steering the wheel
completely. A - direction indicator bulb protective
flap
B - dipped/main beam headlight bulb
protective flap
Side lights/daytime
running lights (DRL)
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
Dipped/main beam
headlights
To change the bulb, proceed as follows:
❒
steer the wheel completely;
❒ open the protective flap B fig. 88 by
rotating the fixing screw;
❒ take out the electric connector A fig.
89 and then rotate the bulb holder B
clockwise and remove it; ❒
extract the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
❒ close the protective flap B fig. 88.
Direction indicators
Front
To change the bulb, proceed as follows:
❒ steer the wheel completely;
❒ open the protective flap A fig. 88 by
rotating the fixing screw;
❒ take out the electric connector A fig.
90 and then rotate the bulb holder B
clockwise and remove it;
❒ extract the bulb and replace it;
❒ refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;87
A0L0091
88
A0L0092
89
A0L0093
122
IN AN EMERGENCY
24-9-2013 11:50 Pagina 122

REPLACING FUSESGENERAL INFORMATION
Fuses protect the electrical system:
they intervene (blow) in the event of a
fault or improper action on the system.
When a device does not work, check
the condition of its fuse: the filament
A fig. 101 must be intact.
If it is not, replace the blown fuse with
another with the same amperage (same
colour).
105) 106) 107) 108) 109)
14)
B = intact fuse;
C = fuse with damaged filament.FUSE LOCATION
The fuses are grouped in two fuse
boxes located in the engine and
passenger compartments.
Engine compartment fuse box
This is located next to the battery fig.
102: to access the fuses, undo screws
A and remove cover B.
The number identifying the electrical
component corresponding to each fuse
is shown on the back of the cover.
After replacing the fuse, make sure you
close cover B on the fuse box.
15)
Dashboard fuse box
This is located under the dashboard in
the area in front of the passenger seat.
To access the fuse box fig. 105 remove
the protective panel, following the
procedure described below:
❒
undo the four screws A fig. 104;
❒ to locate the fifth locking screw,
remove block B and remove plastic
cover C;
101
A0L0102
102
A0L0137
103
A0L0104
126
IN AN EMERGENCY
24-9-2013 11:50 Pagina 126

Thousands of kilometres20 40 60 80 100 120
Months 12 24 36 48 60 72
Check condition and wear of rear brake pads and discs, and
operation of pad wear indicator ●●●●●●
Check and, if necessary, top-up fluid levels (engine cooling,
brakes, windscreen washer, etc.) ●●●●●●
Visually inspect condition of the accessory drive belt(s) ●
Inspect the conditions of toothed timing drive belt ●
Check handbrake lever travel and adjust, if necessary (or every 12
months) ●●●●●●
Check exhaust emissions/smokiness ●●●
Check engine control system operation (through diagnosis socket) ●●●●●●
Check and possible top up of oil level for the dual clutch
automatic transmission ●
Replace spark plugs (#) ●●
Replace accessory drive belt(s) ●
Replace toothed timing drive belt (*) ●(#) The following are essential to ensure correct operation and prevent serious damage to the engine: only use spark plugs of the same make and type which are
specially certified for such engines (see the information in the “Engine” paragraph in the “Technical specifications” section); strictly comply with the spark plug
replacement interval given in the Scheduled Servicing Plan; for spark plug replacement, it is advisable to contact the dedicated Alfa Romeo Dealership.
(*) Irrespective of the mileage, the timing drive belt must be changed every 4 years for heavy-duty use (cold climates, town use, long periods of idling) or at least every 5 years.
136
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 136

The plugs for topping the brake fluid and the windscreen washer fluid are located between the bonnet and the windscreen, by
respectively removing the suitable panel D and the suitable protection grid E; to top up, use the suitable kit supplied as
standard (see descriptions below).
19)111
A0L0153
140
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 140

ENGINE OIL
Check that the oil level is between the
MIN and MAX marks on the dipstick
A fig. 110.
For this check, take out the dipstick
from its seat, clean it with a lint-free
cloth, reinsert the dipstick; take it out
again and check the oil level.
116)
If the oil level is near or under the MIN
mark, add oil through the filler B fig.
110 until it reaches the MAX mark.
20)
Take out the engine oil dipstick A, clean
it with a lint-free cloth and reinsert it.
Extract the engine oil dipstick again and
check that the level is between the
MIN and MAX marks on the dipstick.
116)
The range between the MIN and MAX
levels corresponds to approximately
1 litre of oil.
Engine oil consumption
21)
3)
The maximum engine oil consumption
is usually 400 grams every 1,000 km.
When the car is new, the engine needs
to run in, therefore the engine oil
consumption can only be considered
stabilised after the first 5,000 - 6,000
km.IMPORTANT After adding or changing
the oil, let the engine run for a few
seconds and wait a few minutes after
stopping it before you check the level.
ENGINE COOLANT
22)
117)
The coolant level must be checked
when the engine is cold and must
range between the MIN and MAX
marks on the reservoir.
If the level is too low, unscrew reservoir
plug C fig. 110 and add the fluid
described in the "Fluids and lubricants"
paragraph of the "Technical
Specifications" chapter.
WINDSCREEN WASHER
FLUID
118) 119)
To check the windscreen washer fluid
level, proceed as follows:
❒
to avoid any interference during the
procedure, lift the windscreen wiper
blade according to the "Windscreen
wiper" paragraph in the
"Maintenance and care" chapter;
❒ loosen the 4 self-tapping screws A
fig. 112 using the supplied
screwdriver. Remove the bonnet
grille;
❒ release the plug from the opening; ❒
leaving the plug close to the opening,
put a finger on the central hole B fig.
113 in the plug and remove it: the
level can be seen on the control pipe
C fig. 114 due to capillarity;
❒ after the check, reinsert the plug B
with the control pipe C in the initial
position;
❒ reposition the bonnet grille and
tighten the 4 self-tapping screws A.
WARNING Re-close the plug holding it
horizontally (not directed towards the
bonnet) to prevent the opening tang
from remaining locked in a position
difficult to reach.
It is recommended to check the
windscreen washer fluid regularly, in
particular in driving conditions needing
a heavier use of the windscreen washer.
112
A0L0130
141
24-9-2013 11:50 Pagina 141

WARNING
113) The Alfa Romeo 4C is designedand produced for road use, in
compliance with the current
regulations. Vehicle use in the
track must be considered as
occasional and in any case under
the responsibility of the user.
The vehicle CANNOT be modified
or tampered with for any reason,
this would alter the Manufacturer
homologation and/or safety
requirements. Using a modified or
tampered product relieves the
Manufacturer from any
responsibility on it and may
expose people to serious risks.
114) Never smoke when performing operations in the engine
compartment. Flammable gases
and fumes may be present, with
the risk of fire.
115) Be very careful when working in the engine compartment if the
engine is hot: risk of burns. 116) If the engine oil is being topped
up, wait for the engine to cool
down before loosening the filler
plug, particularly for cars with
aluminium plug (for versions/
markets, where provided).
WARNING: risk of burns!
117) The cooling system is pressurised. If necessary, only
replace the plug with another
original one or the operation of
the system may be adversely
affected. Do not remove the
reservoir plug when the engine is
hot: risk of burns.
118) Do not travel with the windscreen washer reservoir
empty: the windscreen washer is
essential for improving visibility.
Repeated operation of the system
without fluid could damage or
cause rapid deterioration of some
system components.
119) Certain commercial additives for windscreen washer fluids are
inflammable. The engine
compartment contains hot
components which may set it on
fire. 120) Brake fluid is poisonous and
highly corrosive. In the event of
accidental contact, immediately
wash the affected parts with
water and mild soap. Then rinse
thoroughly. Call a doctor
immediately if swallowed.
121) The
symbol on the container
indicates a synthetic brake fluid,
which is different from a mineral
fluid. Using a mineral fluid will
damage the special rubber seals
of the braking system beyond
repair.IMPORTANT
3) Used engine oil and oil filters contain substances which are
harmful to the environment. You
are advised to go to a dedicated
Alfa Romeo Dealership to have
the oil and filters changed.
144
SERVICING AND MAINTENANCE
24-9-2013 11:50 Pagina 144

AIR CLEANERFor cleaner replacement, contact a
dedicated Alfa Romeo Dealership.
BATTERYBattery A fig. 118 does not require the
electrolyte to be topped up with distilled
water. A periodic check carried out at
a dedicated Alfa Romeo Dealership
is, however, necessary to check
efficiency.
REPLACING THE
BATTERY
122) 123) 124) 125)25)4)
If necessary, replace the battery with
another original battery with the same
specifications. Follow the battery
manufacturer's instructions for
maintenance.USEFUL ADVICE FOR
EXTENDING THE LIFE OF
YOUR BATTERY
To avoid draining your battery rapidly
and maintain its efficiency over time,
carefully observe the following
instructions:
❒
when you park the car, ensure that
the doors and tailgate are properly
closed, to prevent roof lights inside
the passenger and luggage
compartments respectively from
staying on;
❒ switch off the roof lights; the car is,
however, equipped with a system
which switches the interior lights off
automatically;
❒ do not keep accessories (e.g. radio,
hazard warning lights, etc.) switched
on for a long time when the engine
is not running;
❒ before performing any operation on
the electrical system, disconnect
the negative battery cable.
IMPORTANT If the charge level remains
under 50% for a long time, the battery
is damaged by sulphation, reducing
its capacity and efficiency at start-up.118
A0L0138
145
24-9-2013 11:50 Pagina 145