2013 Alfa Romeo 4C brake

❒If it is necessary to proceed downhill
with transmission in neutral (N) for
unexpected reasons, bearing in mind
that this practice is highly inadvisable,
remember that when gear
engagement is requested, the
system will automatically engage the
best gear to permit the correct
transmission of drive torque to the
wheels, according to the speed
of the car.
❒ When necessary, it is possible to
engage 1st gear, reverse (R) or
neutral (N) with the engine off, the
key at MAR-ON and the brake
pressed. In this case, change gear
leaving at least 5 seconds between
one gear change and the next, in
order to safeguard the operation of
the hydraulic system, and the pump
in particular.
❒ For uphill departures, it is advisable
to accelerate gradually but fully
immediately after releasing the
handbrake or the brake pedal; this
allows the engine to temporarily
increase the number of revs and
tackle the steepest gradients with
more torque at the wheels.
SAVING FUELAlfa Romeo has designed and built the
vehicle using technologies, materials
and devices able to reduce negative
environmental impact. Here are some
suggestions to further contribute to
environmental protection.
GENERAL
CONSIDERATIONS
Car maintenance
Have checks and adjustments carried
out in accordance with the “Scheduled
Servicing Plan”.
Tyres
Check the tyre pressures at least once
every four weeks: if the pressure is
too low, consumption levels increase as
resistance to rolling is higher.
Climate control system
The use of the climate control system
leads to higher fuel consumption. If the
temperature outside permits, try to
use ventilation only.
109
24-9-2013 11:50 Pagina 109
WARNING
89) The Launch control function is
only available in the Dynamic or
Race mode. Regardless of what is
explicitly indicated in the
description of these modes, the
ESC and ASR systems are
deactivated during operation of
the Launch Control function. This
means that vehicle dynamic
control is always the responsibility
of the driver. Therefore pay the
utmost attention when using the
Launch Control. Take into account
traffic and road surface conditions
and during manoeuvres make
sure there is enough room in the
area concerned.

SNOW TYRESUse snow tyres of the same size as the
normal tyres provided with the car:
the dedicated Alfa Romeo Dealership
will be able to advise you on the most
appropriate tyre to use.
Only use these tyres in the event of ice
or snow on the roads.
For the type of tyre to be used, inflation
pressures and the specifications of
snow tyres, follow the instructions given
in the "Wheels" paragraph in the
"Technical specifications" chapter.
90)
The performance of these tyres on
low-grip surfaces are reduced
considerably when the tread depth is
below 4 mm. They should be replaced
in this case.
Due to the specific characteristics of
snow tyres, in normal weather
conditions or on long motorway
journeys, the performance of these
tyres is lower than that of standard
tyres. Their usage should therefore be
restricted in accordance with their
type approval.IMPORTANT When using snow tyres
with a maximum speed index below the
one that can be reached by the car
(increased by 5%), place a notice in the
passenger compartment, plainly in
view, which states the maximum speed
allowed by the snow tyres (as per EC
Directive).
All four tyres should be the same brand
to ensure greater safety when driving
and braking as well as making the
car more responsive. It is inadvisable to
change the rotation direction of tyres.
Refer to the "Raising the car" section in
the "In an emergency" chapter for
further details on how to raise the car
correctly.
WARNING
90) The maximum speed for snow
tyres marked “Q” is 160 km/h,
while it is 190 km/h for “T” tyres
and 210 km/h for "H" tyres. The
highway code speed limits must
however always be complied with.
CAR INACTIVITYIf the car is to be left inactive for longer
than a month, observe the following
precautions:
❒park the car in covered, dry and if
possible well-ventilated premises and
slightly open the windows;
❒ check that the handbrake is not
engaged;
❒ disconnect the negative battery
terminal and check the battery
charge. Repeat this check once
every three months during storage.
For optimum preservation of the
battery charge, it is advisable to use
the charge-holder (for versions/
markets, where provided, or
alternatively, available from
Lineaccessori). For more details on
its operation, refer to the attached
Supplement;
❒ if the battery is not disconnected
from the electrical system, checks its
state of charge every thirty days;
❒ clean and protect the painted parts
using protective wax;
111
24-9-2013 11:50 Pagina 111

REPAIRING A WHEELGENERAL
INSTRUCTIONS
The car is equipped with a quick tyre
repair device called the "Fix&Go
automatic" kit.
92) 94)
To use it, follow the instructions below.
93) 95) 96)
12)
2)
"Fix&Go automatic" KIT
It is located in the luggage
compartment.
The kit includes:
❒bottle A fig. 80 containing sealant
and fitted with: filling tube B and
adhesive label C with the wording
“max. 80 km/h” to be placed in
a clearly visible position (e.g. on the
dashboard) after repairing the tyre;
❒ compressor D complete with
pressure gauge and connectors;
❒ an information leaflet fig. 81,
providing instructions for using the kit
correctly. This booklet should be
given to the persons charged with
handling the tyre treated with this kit;
❒ a pair of gloves located in the side
compartment of the compressor;
❒ adaptors for inflating different
elements. IMPORTANT The sealant is suitable for
use at temperatures in the range from
−20°C to +50°C. The sealant has an
expiry date. INFLATION PROCEDURE
Proceed as follows:
97)
❒
engage the handbrake, unscrew the
tyre valve cap, take out filler hose A
fig. 82 and tighten ring nut B on
the tyre valve;
❒ make sure that switch A fig. 83 for
the compressor is in position 0 (off),
start the engine, insert the plug
into the cigar lighter socket on the
central tunnel (see fig. 84) and switch
on the compressor by bringing
switch A fig. 83 to I (on);
❒ inflate the tyre to the pressure
indicated in the “Wheels” paragraph
in the “Technical data” chapter. In
order to obtain a more precise
reading, check the pressure value on
pressure gauge B fig. 83 with the
compressor off;
80
A0L0076
81
A0L0077
82
A0L0078
115
24-9-2013 11:50 Pagina 115

❒if after 5 minutes it is impossible to
reach at least 1.8 bar, disconnect
the compressor from the valve and
power socket, then move the car
forwards approximately 10 metres in
order to distribute the sealant inside
the tyre evenly, then repeat the
inflation operation; ❒
if you still cannot obtain a pressure of
at least 1.8 bar within 5 minutes from
the compressor switching on, do
not drive off and contact a dedicated
Alfa Romeo Dealership;
❒ after driving for about 10 minutes
stop and check the tyre pressure
again; remember to engage the
handbrake;
❒ if a pressure value of at least 1.8 bar
is detected, restore the correct
pressure (with the engine running and
the handbrake engaged), resume
driving and drive with great care to a
dedicated Alfa Romeo Dealership.
98) 99) 100)
CHECKING AND
RESTORING TYRE
PRESSURE
The compressor can also be used to
check and, if necessary, restore the tyre
pressure.
Release quick connector A fig. 85 and
connect it directly to the valve of the
tyre to be inflated. REPLACING THE BOTTLE
Proceed as follows:
❒
release connector A fig. 86 and
disconnect tube B;
❒ turn the bottle to be replaced
anticlockwise and raise it;
❒ insert the new bottle and turn it
clockwise;
❒ insert connector A and tube B in their
housings.
83
A0L0079
84
A0L0080
85
A0L0081
86
A0L0082
116
IN AN EMERGENCY
24-9-2013 11:50 Pagina 116

BulbsTypePowerRef. Figure
Front side lights/Daytime running lights (DRL) LED--
Rear side lights LED--
Dipped/Main beam headlights (versions with
Bi-Halogen headlights) (for versions/markets,
where provided) H7
55 W D
Dipped/Main beam headlights (versions with
Bi-Xenon headlights) (for versions/markets, where
provided) D1S
35 W -
Dipped/Main beam headlights (versions with
Bi-LED headlights) (for versions/markets, where
provided) LED
--
Front direction indicators PY21W21 W B
Rear direction indicators PY21W21 W B
Side direction indicators WY5W5 WA
Brake lights LED--
3rd brake light LED--
Number plate lights W5W5 W A
Rear fog light W16W16 W A
Reversing light W16W16 W A
Roof light C10W10 W C
Luggage compartment light W5W5 W A
121
24-9-2013 11:50 Pagina 121

❒close the protective flap A fig. 88.
Side
To change the bulb, proceed as follows:
❒ adjust the lens A in the point shown
in figure fig. 91 to compress the
retaining clip B, then pull the cluster
outwards;
❒ turn the bulb holder B anticlockwise,
extract the bulb and replace it;
❒ refit the bulb holder B in the lens and
turn it clockwise;
❒ refit the cluster making sure that the
internal clip clicks into position. REAR LIGHT CLUSTERS
These contain the bulbs for the side
lights, direction indicators and brake
lights.
Direction indicators
To change the bulb, proceed as follows:
❒
remove the protective cap A fig. 92
(one for each side) on the side cover
of the luggage compartment.
❒ remove the second protective cap in
rubber B fig. 93 inserting the hand
inside the hole.
❒ rotate the bulb holder and extract it;
❒ replace the bulb by pressing it and
turning it anticlockwise;
❒ refit the previously removed
protective caps. Side lights/brake lights
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.90
A0L0094
91
A0L0095
92
A0L0096
93
A0L0134
123
24-9-2013 11:50 Pagina 123

REAR FOG LIGHT/
REVERSING LIGHT
104)
To replace the rear fog light bulbs A fig.
94 or the reversing lights B fig. 94
proceed as follows:
❒turn the bulb holder C fig. 95
anticlockwise, extract the bulb and
replace it. 3
rd
BRAKE LIGHTS
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
NUMBER PLATE LIGHTS
To replace the bulbs proceed as
follows:
❒ adjust the lens A in the point shown
in figure fig. 96 laterally to compress
the retaining clip, then pull the
number plate light cluster A out;
❒ turn bulb holder B fig. 97
anticlockwise, extract bulb C and
replace it.
WARNING
104) The rear fog light and the
reversing light are located close to
the exhaust pipes; take the
utmost care not to get burnt
during the bulb replacement.
94
A0L0097
95
A0L0126
96
A0L0136
97
A0L0099
124
IN AN EMERGENCY
24-9-2013 11:50 Pagina 124

❒at this point undo the fifth screw D
and remove the protective panel to
locate the fuse box.
WARNING
105) If a fuse blows again, contact a
dedicated Alfa Romeo Dealership.
106) Never replace a fuse with another with a higher amp rating;
DANGER OF FIRE. 107) If a general protective fuse
(MAXI-FUSE, MEGA-FUSE,
MIDI-FUSE) blows, contact a
dedicated Alfa Romeo Dealership.
108) Before replacing a fuse, make sure that the ignition key has
been removed and that all the
other services are switched off
and/or deactivated.
109) Contact a dedicated Alfa Romeo Dealership if a safety
system (airbags, brakes),
transmission system (engine,
gearbox) or steering system
general protection fuse blows.
IMPORTANT
14) Never replace a blown fuse withmetal wires or other material.
15) If you need to wash the engine compartment, take care not to
aim the jet of water directly at the
fuse box.
104
A0L0105
105
A0L0106
127
24-9-2013 11:50 Pagina 127