2013 Acura TL turn signal

I N S T R U M E N T P A N E L I N D I C A T O R S
O n / O f f I n d i c a t o r s
M a l f u n c t i o n I n d i c a t o r s
If an indicator remains on, there may be a \3problem; see your dealer\b
Charging system
Low brake fluid, Brake system
Low oil pressure
SHAWD*(Super Handling AllWheel Drive)
VSA®
(Vehicle Stability Assist)
Malfunction indicator lamp(check engine light)
TPMS (blinks)(Tire Pressure Monitoring System)SRS(Supplemental Restraint System)
ABS (Antilock Brake System)EPS(Electronic Power Steering System)
OFF
PASSENGER AIRBAGPASSENGER AIRBAG OFF
(above audio panel)
SIDE AIRBAG OFF
VSA OFF
Fog lights on
Headlights on
Turn signals/hazards on
CRUISE CONTROL on
CRUISE MAIN on
High beams on
Briefly appear with each engine start\b Red and \3amber indicators are most critical\b
Blue and green indicators are used for general \3information\b See your Owner’s Manual
for more information\b
*if equipped
5
4
C o n d i t i o n I n d i c a t o r s
Action is needed by driver\b
Parking brake on:
ReleaseMessage indicator:
See MI\f
Door/trunk open:
Close door or trunkLow tire pressure (stays on):
Add air
Seat belt reminder:
Fasten seat belt(s)Low fuel:
Refill
BSI*(Blind Spot Information System)Keyless Access System
Immobilizer (blinks):
Use correct key
13 TL ATG_Tech_ATG_\ANEW STYLE 8/14/201\A2 2\f00 PM Page 4
*

B L I N D S P O T I N F O R M A T I O N ( B S I ) S Y S T E M ( A d v a n c e P a c k a g e )
Assists you in determining if there are vehicles\3 in your blind spots\b
T u r n i n g B S I O f f / O n
A radar sensor on each corner of the rear \3bumper alerts you to a detected
vehicle in your blind spot\b
Minimum operating speed: 67 mph
When a vehicle is detected in
your blind spot, the blind spot
indicator turns on and stays lit until
the area is clear\b
H o w I t W o r k s
When your turn signal is on and a
vehicle is detected, the blind spot
indicator blinks until the area is
clear or the turn signal is turned off\b
Press and hold
the BSI OFF
button on the
dashboard to
turn BSI off or on\b
A message
briefly appears
on the MID
screen showing
the system status\b
\f8 \f9
1\f
13
Left BSI indicator shown
H O M E L I N K ®
Press and hold
the button on the
remote and the HomeLink button at
the same t ime. Then, whil e
continuing to hold the HomeLink
button, press and release the button
on the remote every 2 seconds.
Does the LED blink at a faster rate within 20
seconds?
Press and hold
the HomeLink
button again. Training
complete
YES
NO
HomeLink indicator
flashes for 2 seconds,
then remains on. HomeLink LED
remains on.YES
NO YES
NO
Position the remote transmitter you
wish to link 1–3 inches from the
HomeLink button you want to program.1
Press and hold the desired
HomeLink button and the button on
the remote transmitter.
Does the HomeLink indicator (LED) blink at a
faster rate after about 10 seconds?
2
a
The remote has a rolling code.
Press the “learn” button on the
remote-controlled device (e.g.,
garage door opener).
Press the programmed HomeLink
button again; the remote-controlled
device should operate. Within 30 seconds, press and
hold the programmed HomeLink
button for 2 seconds.a
Press and hold the programmed
HomeLink button for about a
second.
Does the device (garage door opener) work?
3
b
4
5
T r a i n i n g a B u t t o n
Program your vehicle to operate up to three remo\3tecontrolled devices around your
home, such as garage doors, lighting, or h\3ome security systems\b
If you have any problems programming HomeLink, \3see the owner’s manual
included with the device you are trying to progr\3am, call HomeLink at
(800) 3553515, or visit www.homelink.com.
13 TL ATG_Tech_ATG_\ANEW STYLE 8/14/201\A2 2\f01 PM Page 8