2013 Acura TL key battery

When you lock the doors, some
exterior lights blink and the system
beeps once. If no exterior lights blink
and/or no beeper sounds, check to
see if the trunk or hood is open.
To change the ‘‘KEYLESS
ACCESS LIGHT FLASH’’ setting,
see page.
To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page .
Within 2 seconds of pressing the
door lock button or locking the doors
with the remote, pull the handle to
make sure the doors are actually
locked. The door unlock sensors will
not operate f or about 2 seconds af ter
the doors are locked. The door lock button does not
work if:
Theremoteisnotwithinthe
operating range. If you open the driver’s door, pull its
locktabrearwardonthedoor,and
shutitwhentheremoteisinsidethe
vehicle, the driver’s door will unlock.
Make sure you carry the remote
with you when you lock the doors.
Any door is open.
The power mode is not set to
VEHICLE OFF (LOCK).
The remote is in the keyless
access slot.
The remote is too close to the
vehicle.
Theremotebatteryisdead.
The vehicle battery is dead. This function is also activated on the
f ront passenger’s door. If you open
the f ront passenger’s door, and shut
it af ter pulling its lock tab rearward
whentheremoteisinsidethevehicle,
all doors will unlock.
The door lock prevention will also
activate if you try to lock the doors
with the master door lock switch
whentheremoteisinsidethevehicle.
117
118
K eyless A ccess System
Door L ock Prevent ion
Inst rument s and Cont rols
177
12/07/20 10:52:18 31TK4640_182
2013 TL

´
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal.
Battery type: CR2032 Replace the battery if necessary.
To replace the battery:
Replace the old battery with a new
battery. Place the battery so the
side is f acing up. Snap the two
halvesof theremotecaseback
together.
Remove the built-in key (see page ).
Place a cloth on the edge to
prevent scratches, then remove
the upper half by caref ully prying
on the edge with a coin. This device complies with the
appropriate requirements or the
required standards. See page f or
more inf ormation.
1.
2. 3.
201 628
Replacing the Remote Battery
K eyless A ccess System
Inst rument s and Cont rols
181
12/07/20 10:52:52 31TK4640_186
2013 TL

Af ter entering the vehicle, insert the
keyless access remote into the slot
to start the engine (see page ). If the keyless access remote battery
dies, you may have to use the
built-in key to unlock/lock the
vehicle. The built-in key is stored
inside the keyless access remote
(see page).
If the steering wheel is locked, the
engine cannot start. The multi-
inf ormation display shows you the
above message and the indicator in
the engine start/stop button blinks.
To unlock the steering wheel, apply
f orce by turning it lef t and right
while pressing the engine start/stop
button at the same time.
the multi-
inf ormation display shows the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message, then the ‘‘TO
START ENGINE:’’ message will be
shown af ter you insert the remote
into the slot. Each time you press the
engine start/stop button, the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message is shown on
the multi-information display if the
remote is not in the slot. 201
197
When the keyless access system mainswitch in the glove box is of f , T o unlock t he st eering wheel
K eyless A ccess System
Inst rument s and Cont rols
189
NOTE:
TO UNLOCK WHEEL
12/07/20 10:54:02 31TK4640_194
2013 TL

Thebatteryintheremotenormally
lasts about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘CHANGE KEYLESS REMOTE
BATTERY,’’ replace the battery as
soon as possible (see page ).If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. Af ter
inserting the remote into the slot,
operate the engine start/stop button
as previously described (see pages
and ). For more information
on the keyless access slot, see page .
Inserting the remote does not charge
the remote battery. You should
replace the battery as soon as
possible.
181 184 187
197
K eyless A ccess System
K eyless Remot e L ow Bat t ery
194
12/07/20 10:54:40 31TK4640_199
Inst rument s and Cont rols
2013 TL

If the remote battery becomes
weak and the power door lock/
unlock operation is disabled.When the keyless access remote
system main switch in the glove
box is set to of f .
In the following two cases, you have
to insert the keyless access remote
into the keyless access remote slot
to set the power mode and start the
engine: To remove the keyless access
remote, place the vehicle in the
VEHICLE OFF (LOCK) mode, then
pull out the keyless access remote.
If the keyless access remote has
been inserted into the slot with the
keyless access remote system main
switch in the glove box turned off, it
will lock into place when the power
is on. The slot will unlock when the
power is turned off.
If the keyless access remote
does not come out of the slot
easily,try to push it in before
pulling it out. Make sure the
vehicle is in VEHICLE OFF
(LOCK) mode.
CONT INUED
K eyless A ccess System
K eyless A ccess Remote Slot
Inst rument s and Cont rols
197
NOTE:
KEYLESS ACCESS REMOTE SLOT
12/07/20 10:55:06 31TK4640_202
On automatic transmission models
The multi-information display
shows the ‘‘ACCESSORY MODE’’
or ‘‘TO UNLOCK KEYLESS
REMOTE TURN OFF POWER’’
message to remind you to change
the power mode to VEHICLE OFF
(LOCK).
2013 TL

To insert the keyless access remote:
On all models
On manual transmission models
When you open the driver’s door,
and each time you press the engine
start/stop button, you will see the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message on the multi- inf ormation display in the f ollowing
situations:
When the keyless access system
main switch (see page ) is of f .
The multi-inf ormation display shows
the ‘‘ACCESSORY MODE’’ message
to remind you that the power mode
is in ACCESSORY.
To avoid damaging the slot, do not
insert any other objects into the slot
or put a sticker on the
keyless access remote.
Inserting the remote does not
charge the remote battery. If
necessary, you should replace the
battery as soon as possible.
When the keyless access remote
system main switch in the glove box
issettoON,theremoteremains
unlocked when you insert it into the
keyless access remote slot and the
power mode is turned on. 195
K eyless A ccess System
Operat ion Guidance
Unlocked K eyless A ccess Remot e
198
12/07/20 10:55:16 31TK4640_203
When the keyless access remote
is not in the vehicle.Inst rument s and Cont rols
2013 TL

The trunk and glove box cannot be
opened when you turn the trunk
main switch of f and lock the glove
box and trunk pass-through cover
with the built-in key. Then, the trunk
cannot be opened by using the
remote or the exterior trunk release
switch.
Remove the built-in key from the
remote by pressing the button, then
give that remote to someone else as
a valet key.
To avoid damaging the remote and
the built-in key, never pull on the
built-in key unless you are pressing
the release button.
The keyless access system uses an
electric f ield to identif y the remote.
If you use medical equipment such
as a cardiac pacemaker, ask your
doctor if the electric f ield used by
the remote will af f ect it.
Thebuilt-inkeycanbeusedtolock/
unlock the doors and the trunk when
the remote battery becomes weak
and the power door lock/unlock
operation is disabled.
To remove the built-in key, pull it out
while pressing the release button. To
reinstall the built-in key, push the
key into the remote until it clicks. Valet Function
Built-in key and Remote
K eyless A ccess System
Inst rument s and Cont rols
201
RELEASE BUTTON BUILT-IN KEY
12/07/20 10:55:35 31TK4640_206
2013 TL

You can make calls using any phone
number or a name in the HFL
phonebook. You can also redial the
last number called.
Bluetooth is the wireless technology
that links your phone to HFL. HFL
uses a Class 2 Bluetooth, which
means the maximum range between
yourphoneandvehicleis30feet(10
meters).
During a call, HFL allows you to talk
up to 30 minutes af ter you remove
the key from the ignition switch.
However, this may weaken the
vehicle’s battery.Press and release the HFL Talk
button bef ore a command.
Say ‘‘ ’’ or ‘‘ .’’
Follow the HFL prompts and say
thenamestoredintheHFL
phonebook that you want to call.
Follow the HFL prompts to
conf irm the name and make the
call. Press and release the HFL Talk
button bef ore a command.
Say ‘‘ ’’ or ‘‘ .’’
Follow the HFL prompts and say
the phone number you want to dial.
Follow the HFL prompts to
conf irm the number and say
‘‘ ’’ or ‘‘ .’’
Once connected, you will hear the
person you called through the audio
speakers.
Press and release the HFL Talk
button and say ‘‘ .’’ 1.
2.
3.
1.
2.
3.
Making a Call
Call DialCall Dial
Call Dial
Redial
BluetoothHandsFreeL ink(Models without navigation system)
To make a call using aname in the HFL phonebook: To make a call using a
phone number:
To redial the last numbercalled by HFL:
Features
415
12/07/20 11:23:27 31TK4640_420
2013 TL