44
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
WINDOW WINDERS
FRONT WINDOW WINDERS
fig. 45
They operate with ignition key on MAR
and for about 2 minutes after positioning
the key on STOPor removed.
The two buttons are located besides the
gear lever (one for each side):
Ato open/close the left front window;
Bto open/close the right front window;
With the ignition key to the MARposi-
tion, press the driver's side window op-
erating button for a few seconds to open
or close the window automatically.
As regards the passenger's side window,
only the opening occurs automatically with
the same procedure.
fig. 44F0S044Ab
IMPORTANT If one of the doors is not
properly closed or if there is a fault in the
system, the central locking will not be ac-
tivated. If the operation is repeated 10/11
times in quick succession, the device is ex-
cluded for approximately 30 seconds.
To lock, insert the key in the lock and
turn it to the position 2-fig. 43. When the
key is turned the doors and the tailgate
are simultaneously locked.
To lock the doors with the remote con-
trol press the button Á.Lock/release from inside
To releasepull lever A-fig. 44.
Operating lever A on the driver's side or
on the passenger side releases both doors.
To lock. Push the control lever A-fig. 44
toward the door
Operating the lever on the driver's side or
on the passenger side locks both doors.
The correct lever position with locked doors
is shown by the red symbol A-fig. 44a
visible on the handles.
fig. 44a
A
A
F0S144Ab
023-045 ABARTH 500 1ed GB:023-045 ABARTH 500 GB 24-05-2012 14:54 Pagina 44
51
SAFETY
DEVICES
CORRECT USE
OF THE
CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
YOUR CAR
BEAM ADJUSTMENT fig. 57
The car is provided with electric adjust-
ment of the beams, operating with ignition
key on MARand low beams on.
The car will slant backwards when it is
loaded, raising the light beam.
In that case, it is necessary to perform
beams adjustment with buttons +and –.
The display provides a visual indication of
the positions during adjustment.
Gas discharge headlights (Xenon head-
lights) are automatically adjusted. The
headlight position is electronic and there-
fore cannot be manually adjusted using the
+and –buttons.
fig. 57
M E N UE S C
F0S057Ab
Correct positions depending
on load
Position 0- one or two passengers on
front seats.
Position 1- 4 passengers.
Position 2- 4 passengers + load in the
boot.
Position 3- driver + maximum admitted
load in the boot.
AIMING THE FRONT
FOG LIGHTS
(for versions/markets, where provided)
Contact Abarth Dealership to have the
headlights properly adjusted.
BEAMS ADJUSTMENT ABROAD
Low beams factory adjustment depends
on the country where the car is pur-
chased. When you travel in countries with
different driving direction, to avoid blind-
ing the drivers who travel in the opposite
direction, it is necessary to cover the ar-
eas of the beam according to the provi-
sions of the Highway Code of the country
where you travel.ABS SYSTEM
(for versions/markets, where provided)
The car is fitted with an ABS braking sys-
tem, which prevents the wheels from lock-
ing when braking, makes the most of road
grip and gives the best control when emer-
gency braking under difficulty road condi-
tions.
The system is completed by EBD (Elec-
tronic Braking Force Distribution), which
distributes the braking action between
front and rear wheels.
IMPORTANT To achieve maximum effi-
ciency of the braking system, a settlement
period of about 500 km is required: dur-
ing this time, avoid sudden, repeated and
prolonged braking.
046-062 ABARTH 500 1ed GB:046-064 ABARTH 500 GB 24-05-2012 9:50 Pagina 51
