2012 YAMAHA XVS950 low beam

INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
EAU49391
Indicator lights and warning
lights
EAU11020
Turn signal indicator light“”
This indicator light flashes when the
turn signal switch is pushed to the left or
right.
EAU11060
Neutral indicator light “”
This indicator light comes on when the
transmission is in the neutral position.
EAU11080
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11254
Oil level warning light “”
This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ ON ”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON ”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.TIP

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.


This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection circuit, the following cycle will be
repeated until the malfunction is
corrected: The oil level warning
light will flash ten times, then go off
for 2.5 seconds. If this occurs,
have a Yamaha dealer check the
vehicle.
EAU11365
Fuel level warning light
“”
This warning light comes on when the
fuel level drops below approximately
3.4 L (0.90 US gal, 0.75 Imp.gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ ON ”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON ”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.TIPThis model is also equipped with a self-
diagnosis device for the fuel level de-
tection circuit. If a problem is detected
in the fuel level detection circuit, the fol-
lowing cycle will be repeated until the
1. Neutral indicator light “”
2. Fuel level warning light “”
3. Engine trouble warning light “”
4. Immobilizer system indicator light
5. Oil level warning light “”
6. Turn signal indicator light “”
7. High beam indicator light “”
67
12
4 3
5
U26PE3E0.book Page 4 Tuesday, June 7, 2011 5:19 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3Right
EAU12350
Pass switch
“”
Press this switch to flash the headlight.
EAU12400
Dimmer switch “/”
Set this switch to “” for the high
beam and to “” for the low beam.
EAU12460
Turn signal switch “/”
To signal a right-hand turn, push this
switch to “”. To signal a left-hand
turn, push this switch to “”. When re-
leased, the switch returns to the center position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12500
Horn switch
“”
Press this switch to sound the horn.
EAU12660
Engine stop switch “/”
Set this switch to “” before starting
the engine. Set this switch to “” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12711
Start switch “”
Push this switch to crank the engine
with the starter. See page 5-1 for start-
ing instructions prior to starting the en-
gine.
EAU41700
The engine trouble warning light will
come on when the key is turned to “ON ”
and the start switch is pushed, but this
does not indicate a malfunction.
EAU12733
Hazard switch “”
With the key in the “ON ” or “” posi-
tion, use this switch to turn on the haz-
ard lights (simultaneous flashing of all
turn signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.NOTICE
ECA10061
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-
tery may discharge.
EAU44602
“ SELECT ” switch
This switch is used to perform selec-
tions in the odometer and tripmeters, to
set the clock and to set the brightness
control mode of the multi-function
meter unit.
See “Multi-function meter unit ” on page
3-5 for detailed information.
1. Engine stop switch “/”
2. “SELECT ” switch
3. “RESET ” switch
4. Start switch “”
5. Hazard switch “”
1
5 2
3
4
U26PE3E0.book Page 9 Tuesday, June 7, 2011 5:19 PM

INDEXAAir filter element, replacing ................... 6-12
Auxiliary light bulb, replacing ................ 6-31BBattery................................................... 6-25
Brake and clutch levers, checking and lubricating ........................................... 6-22
Brake and shift pedals, checking and lubricating ........................................... 6-21
Brake fluid, changing ............................ 6-19
Brake fluid level, checking .................... 6-18
Brake lever ............................................ 3-11
Brake lever free play, adjusting............. 6-16
Brake light switches .............................. 6-17
Brake pedal ........................................... 3-11CCables, checking and lubricating .......... 6-21
Care ........................................................ 7-1
Catalytic converter ................................ 3-14
Clutch lever ........................................... 3-10
Clutch lever free play, adjusting ............ 6-15DDimmer switch ........................................ 3-9
Drive belt slack...................................... 6-20EEngine break-in ....................................... 5-3
Engine oil and oil filter cartridge .............. 6-9
Engine stop switch .................................. 3-9
Engine trouble warning light.................... 3-5FFront and rear brake pads, checking .... 6-17
Front fork, checking .............................. 6-24
Fuel ....................................................... 3-12
Fuel consumption, tips for reducing ........ 5-3 Fuel level warning light ........................... 3-4
Fuel tank breather/overflow hose ......... 3-13
Fuel tank cap ........................................ 3-11
Fuses, replacing ................................... 6-26
HHandlebar switches ................................ 3-8
Hazard switch ......................................... 3-9
Headlight bulb, replacing ...................... 6-28
Helmet holder ....................................... 3-15
High beam indicator light ........................ 3-4
Horn switch ............................................. 3-9IIdentification numbers ............................ 9-1
Ignition circuit cut-off system ................ 3-18
Immobilizer system ................................. 3-1
Immobilizer system indicator light........... 3-5
Indicator lights and warning lights .......... 3-4LLicense plate light bulb, replacing ........ 6-30MMain switch/steering lock........................ 3-2
Maintenance and lubrication, periodic .... 6-4
Maintenance, emission control system... 6-3
Matte color, caution ................................ 7-1
Model label ............................................. 9-1
Multi-function meter unit ......................... 3-5NNeutral indicator light .............................. 3-4OOil level warning light.............................. 3-4PPanel, removing and installing................ 6-8
Parking ................................................... 5-4
Part locations .......................................... 2-1Pass switch ............................................. 3-9
RRear suspension, lubricating ................. 6-23
RESET switch ....................................... 3-10
Rider seat .............................................. 3-14SSafety information ................................... 1-1
SELECT switch ....................................... 3-9
Shifting .................................................... 5-2
Shift pedal ............................................. 3-10
Shock absorber assembly, adjusting .... 3-16
Sidestand .............................................. 3-17
Sidestand, checking and lubricating...... 6-23
Spark plugs, checking ............................. 6-8
Specifications .......................................... 8-1
Starting the engine .................................. 5-1
Start switch.............................................. 3-9
Steering, checking................................. 6-24
Storage.................................................... 7-3
Supporting the motorcycle .................... 6-32
Swingarm pivots, lubricating ................. 6-23TTail/brake light bulb, replacing .............. 6-29
Throttle grip and cable, checking and
lubricating ........................................... 6-21
Throttle grip free play, checking ............ 6-13
Tires ...................................................... 6-13
Tool kit..................................................... 6-2
Troubleshooting .................................... 6-33
Troubleshooting chart ........................... 6-34
Turn signal indicator light ........................ 3-4
Turn signal light bulb, replacing ............ 6-30
Turn signal switch ................................... 3-9
U26PE3E0.book Page 1 Tuesday, June 7, 2011 5:19 PM