2012 YAMAHA XT660Z drain bolt

1
2
3
4
5
6
7
8
9
10
3-2
DESCRIPTIO\f
10. Grab bar
11. Main fuse (\fage 7-31)
12. \battery (\fage 7-30)
13. Rear brake fluid reservoir (\fage 7-22)14. Coolant reservoir (\fage 7-13) 15. Front brake fluid reservoir (\fage 7-22)
16. Coolant drain bolt (\fage 7-12)
17. Engine oil filter element (\fage 7-11)
18. \brake \fedal (\fage 4-11)
EAU10420Righ\b view
XT660Z 01-03 ING-AUS:AUSTRALIA 11-05-2009 9:57 Pagina 15

PERIODIC MAINTENANCE AND ADJUSTMENT
7-10
1
2
3
4
\f
6
7
8
\b
10
To change the engine oil
(with or without oil filter element
replacement)
1. Mounting screw
2. \fngine guard
1. Start t\be engine, warm it up for sev- eral minutes, and t\ben turn it off.
2. To reac\b t\be drain bolt of t\be crankcase and t\be drain bolt of
t\be oil tank, remove t\be engine
guard by removing t\be screws.
3. Place an oil pan under t\be engine to collect t\be used\2 oil.
4. Remove t\be engine oil filler cap and t\be drain bolt to drain t\be oil
from t\be crankcase.
5. Remove t\be drain bolt to drain t\be oil from t\be oil ta\2nk.
1. \fngine oil crankcase drain bolt
1. \fngine oil tank drain bolt
6. Remove t\be oil filter elementdrain bolt to drain t\be oil from t\be
oil filter element\2.
1
\fCA10010
NOTICE
Do not operate the vehicle until you
know that the engine oil level is suf-
ficient.
\fWA10360
WARNING0
Never remove the engine oil tank
cap after high-speed operation,
otherwise hot engine oil could
spout out and cause damage or in-
jury. Always let the engine oil cool
down sufficiently before removing
the oil tank cap.
4. If t\be engine oil is below t\be mini- mum level mark, add sufficient oil
of t\be recommended type to raise
it to t\be correct l\2evel.
5. Install t\be oil fil\2ler cap.
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:09 Pagina 7-10

1
2
3
4
5
6
7
8
9
10
PERIODIC M\fINTEN\fNCE \fND \fDJ\bSTMENT
7-11
Tightening torques:Oil filter element\0 cover bolt:10 \fm (1.0 m·\bgf, 7.2 ft·lbf)
Oil filter element\0 drain bolt: 10 \fm (1.0 m·\bgf, 7.2 ft·lbf)
Tightening torques:Engine oil drain bolt (cran\bcase):30 \fm (3.0 m·\bgf, 22 ft·lbf)
Engine oil drain bolt (oil tan\b)\0: 18 \fm (1.8 m·\bgf, 12.9 ft·lbf)
13. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil filter
cap.
10. Install the oil filter element drain
bolt.
11. Tighten the oil filter element cover bolts and the oil filter element
drain bolt to their specified
torques.1. Engine oil filter element
2. O-rings
12. Install the engine oil drain bolts,and then tighten them to their
specified torques.
TIP
S\bip steps 7-9 if the oil filter element is
not being replaced\0.
7. Remove the oil filter element cov- er by removing the bolts.
8. Remove and replace the oil filter element and O-rings.
9. Install the oil filter element cover by installing the bo\0lts.
TIP
Ma\be sure that the O-rings are proper-
ly seated.
1. Engine oil filter element drain bolt
2. Oil filter element cover bolts
2
1
XT660Z 05-07 ING-AUS:MY03 04-06 ING 11-05-2009 10:09 Pagina 7-11