Page 18 of 84
1
2
3
4
5
6
7
8
9
3-2
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAU49391
Indicator lights and warning
lights
SELECT
RESET
ODOOIL
TRI P 1 BE
L
T TRIP 2
OIL CHANGECLOOK
OUT TEM
P
3
24
1 1
1. Turn signal indicator lights “4” and “6”
2. Coolant temperature warning light “
”
3. High beam indicator light “&”
4. Engine trouble warning light “
”
EAU11030
Turn signal indicator lights “4”
and “6”
The corresponding indicator light
fl ashes when the turn signal switch is
pushed to the left or right.
EAU11080
High beam indicator light “&”
This indicator light comes on when the
high beam of the headlight is switched
on. To unlock the steering
2
1
1. Turn.
2. Release.Push the key in, and then turn it to
“OFF” while still pushing it.
EAU11446
Coolant temperature warning light
“
”
This warning light comes on if the
engine overheats. If this occurs, stop
the engine immediately and allow the
engine to cool.
The electrical circuit of the warning
light can be checked by turning the
key to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come
on initially when the key is turned to
“ON”, or if the warning light remains
on, have a Yamaha dealer check the
electrical circuit.
ECA10021
NOTICEDo not continue to operate the en-
gine if it is overheating.TIP● For radiator-fan-equipped vehi-
cles, the radiator fan(s) automati-
cally switch on or off according
52S-F8199-E0_CS.indd 3-252S-F8199-E0_CS.indd 3-2
2011/11/16 13:07:002011/11/16 13:07:00
Process BlackProcess Black
Page 23 of 84
1
2
3
4
5
6
7
8
9
3-7
EAU1044E
INSTRUMENT AND CONTROL FUNCTIONS
EAU12349
Handlebar switchesLeft
132
1. Dimmer switch “%/&”
2. Turn signal switch “4/6”
3. Horn switch “*”Right
1
1. Start switch “,”
EAU12400
Dimmer switch “&/%”
Set this switch to “&” for the high
beam and to “%” for the low beam.
EAU12460
Turn signal switch “4/6”
To signal a right-hand turn, push this
switch to “6”. To signal a left-hand
turn, push this switch to “4”. When
released, the switch returns to the
center position. To cancel the turn
signal lights, push the switch in after it
has returned to the center position.
EAU12500
Horn switch “*”
Press this switch to sound the horn.
EAUM1132
Start switch “,”
Push this switch while applying the
front or rear brake to crank the en-
gine with the starter. See page 5-1 for
starting instructions prior to starting
the engine.
EAUS2010
Front brake lever
1
1. Front brake leverThe front brake lever is located on
the right handlebar grip. To apply the
front brake, pull this lever toward the
handlebar grip.
This model is equipped with a unifi ed
brake system.
As this system is mechanical, addi-
tional free play can be felt in the front
brake lever when the rear brake lever
is being applied. See “Rear brake
lever” for detailed information on the
unifi ed brake system.
52S-F8199-E0_CS.indd 3-752S-F8199-E0_CS.indd 3-7
2011/11/16 13:07:002011/11/16 13:07:00
Process BlackProcess Black
Page 66 of 84
1
2
3
4
5
6
7
8
9
6-29
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24181
Tail/brake light
1
1. Tail/brake lightThis model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come
on, have a Yamaha dealer check it.
EAUT3650
Replacing a front turn signal
light bulbIf a front turn signal light burns out, re-
place it as follows.
1. Remove cowling A. (See page
6-7.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
1
1. Turn signal light bulb socket
3. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
4. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
5. Connect the coupler, and then in-
stall the headlight bulb cover.
6. Install the cowling together with
the headlight unit.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
52S-F8199-E0_CS.indd 6-2952S-F8199-E0_CS.indd 6-29
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black
