2012 YAMAHA XENTER 150 change wheel

1
2
3
4
5
6
7
8
9
1-4
Q
SAFETY INFORMATION
Aftermarket Parts, Accessories,
and Modi cations
While you may fi nd aftermarket prod-
ucts similar in design and quality to
genuine Yamaha accessories, recog-
nize that some aftermarket accesso-
ries or modifications are not suitable
because of potential safety hazards
to you or others. Installing aftermarket
products or having other modifi cations
performed to your vehicle that change
any of the vehicle’s design or opera-
tion characteristics can put you and
others at greater risk of serious injury
or death. You are responsible for inju-
ries related to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under
“Loading” when mounting accesso-
ries.●
Never install accessories or carry
cargo that would impair the per-
formance of your scooter. Care-
fully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering travel or control operation, or ob-
scure lights or refl ectors.
• Accessories fitted to the han-
dlebar or the front fork area can
create instability due to improp-
er weight distribution or aerody-
namic changes. If accessories
are added to the handlebar or
front fork area, they must be
as lightweight as possible and
should be kept to a minimum.
• Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to
lift the scooter, or the scooter
may become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
• Certain accessories can dis-
place the operator from his or
her normal riding position. This
improper position limits the
freedom of movement of the
operator and may limit control
ability, therefore, such acces-sories are not recommended.
●
Use caution when adding electri-
cal accessories. If electrical ac-
cessories exceed the capacity of
the scooter’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your
scooter were designed to match the
performance capabilities and to pro-
vide the best combination of handling,
braking, and comfort. Other tires,
rims, sizes, and combinations may not
be appropriate. Refer to page 6-17 for
tire specifications and more informa-
tion on replacing your tires.
Transporting the Scooter
Be sure to observe following instruc-
tions before transporting the scooter
in another vehicle.
●
Remove all loose items from the
scooter.
●
Point the front wheel straight
ahead on the trailer or in the truck
52S-F8199-E0_CS.indd 1-452S-F8199-E0_CS.indd 1-4
2011/11/16 13:06:592011/11/16 13:06:59
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-13
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.2 L (0.21 US qt, 0.18 Imp.qt)8. Install the final transmission oil
fi ller cap and its new O-ring, and
then tighten the oil fi ller cap.
9. Check the fi nal transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAU20070
CoolantThe coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specifi ed in the periodic maintenance
and lubrication chart.
EAUT3690
To check the coolant level
The coolant level should be checked
as follows before each ride. In addi-
tion, the coolant must be changed at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Place the vehicle on the center-
stand.TIP● The coolant level must be
checked on a cold engine since
the level varies with engine tem-
perature.● Make sure that the vehicle is po-
sitioned straight up when check-
ing the coolant level. A slight tilt
to the side can result in a false
1
1. Final transmission oil drain bolt6. Install the final transmission oil
drain bolt and its new gasket, and
then tighten the bolt to the speci-
fi ed torque.Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)7. Refi ll with the specifi ed amount of
the recommended fi nal transmis-
sion oil. WARNING! Make sure
that no foreign material enters
the final transmission case.
Make sure that no oil gets on
the tire or wheel.
[EWA11311]
52S-F8199-E0_CS.indd 6-1352S-F8199-E0_CS.indd 6-13
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
6-19
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22170
Adjusting the rear brake lever
free play11. Rear brake lever free playThe brake lever free play should mea-
sure 10 ~ 15 mm (0.4 ~ 0.6 in) as
shown. Periodically check the brake
lever free play and, if necessary, ad-
just it as follows.
EAUS2001
Checking the front brake le-
ver free play
1
1. Front brake lever free playPeriodically check the brake lever free
play. If the free play exceeds 10 mm
(0.39 in), have a Yamaha dealer ad-
just it.
EWA10641
WARNING
An incorrect brake lever free play
indicates a hazardous condition in
the brake system. Do not operate
the vehicle until the brake system
has been checked or repaired by a
Yamaha dealer.
EAU21962
Cast wheelsTo maximize the performance, dura-
bility, and safe operation of your ve-
hicle, note the following points regard-
ing the specifi ed wheels.● The wheel rims should be
checked for cracks, bends, warp-
age or other damage before each
ride. If any damage is found,
have a Yamaha dealer replace
the wheel. Do not attempt even
the smallest repair to the wheel.
A deformed or cracked wheel
must be replaced.● The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced.
An unbalanced wheel can result
in poor performance, adverse
handling characteristics, and a
shortened tire life.
52S-F8199-E0_CS.indd 6-1952S-F8199-E0_CS.indd 6-19
2011/11/16 13:07:012011/11/16 13:07:01
Process BlackProcess Black

1
2
3
4
5
6
7
8
9
8-1
SPECIFICATIONS SPECIFICATIONS
EAU50910
DimensionsOverall length
1990 mm (78.3 in)
Overall width
690 mm (27.2 in)
Overall height
1135 mm (44.7 in)
Seat height
785 mm (30.9 in)
Wheelbase
1385 mm (54.5 in)
Ground clearance
140 mm (5.51 in)
Minimum turning radius
2100 mm (82.7 in)WeightCurb weight
142 kg (313 lb)EngineEngine type
Liquid cooled 4-stroke, SOHC
Cylinder arrangement
Single cylinder
Displacement
155 cm
3
Bore x stroke
58.0 x 58.7 mm (2.28 x 2.31 in)
Compression ratio
11.00 : 1
Starting system
Electric starter
Lubrication system
Wet sump
Engine oilRecommended brand
YAMALUBE
Type
SAE 10W-40, 10W-50, 15W-40, 20W-40
or 20W-50
–20 –10 0
1020 30 40 50 ˚C 10 30 50 70 90 110 0 130 ˚F
SAE 20W-50SAE 20W-40SAE 15W-40SAE 10W-40SAE 10W-50
Recommended engine oil grade
API service SG type or higher, JASO
standard MAEngine oil quantityPeriodic oil change
1.10 L (1.16 US qt, 0.97 Imp.qt)Final transmission oilType
SAE 10W-30 type SE motor oil
Quantity
0.20 L (0.21 US qt, 0.18 Imp.qt)Cooling systemCoolant reservoir capacity
(up to the maximum level mark)
0.25 L (0.26 US qt, 0.22 Imp.qt)
Air lterAir fi lter element
Oil-coated paper elementFuelRecommended fuel
Regular unleaded gasoline only
Fuel tank capacity
8.0 L (2.11 US gal, 1.76 Imp.gal)Throttle bodyID mark
52S1 01
Manufacturer
AISANSpark plug(s)Manufacturer/model
NGK / CPR9EA-9
Spark plug gap
0.8-0.9 mm (0.031-0.035 in)ClutchClutch type
Dry, centrifugal automaticTransmissionPrimary reduction ratio
1.000
Secondary reduction ratio
10.320 (46 / 13 x 35 / 12)
Final drive
Gear
Transmission type
V-belt automaticChassisFrame type
Underbone
52S-F8199-E0_CS.indd 8-152S-F8199-E0_CS.indd 8-1
2011/11/16 13:07:022011/11/16 13:07:02
Process BlackProcess Black