Page 33 of 84
1
2
3
4
5
6
7
8
9
4-3
EAU15582
FOR YOUR SAFETY - PRE-OPERATION CHECKS
ITEM CHECKS PAGE
Wheels and tires• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.6-17~6-19
Brake levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.3-7~3-8, 6-23
Centerstand• Make sure that operation is smooth.
• Lubricate pivot if necessary.6-23
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.-
Instruments, lights, signals
and switches• Check operation.
• Correct if necessary.3-2~3-7
53B-F8199-E0_CS.indd 4-353B-F8199-E0_CS.indd 4-3
2011/11/01 12:32:092011/11/01 12:32:09
Process BlackProcess Black
Page 41 of 84
1
2
3
4
5
6
7
8
9
6-4
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17717
General maintenance and lubrication chartNO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi)6000 km
(3500 mi)
12000 km
(7000 mi)18000 km
(10500 mi)24000 km
(14000 mi)
1 Air lter element• Replace. Every 20000 km (12500 mi)
2 Air lter check hose• Clean.
√√√√√
3V-belt case air lter ele-
ment• Clean.
√√√√
• Replace. Every 20000 km (12500 mi)
4 * Front brake• Check operation, fl uid level and vehicle for fl uid leakage.
√√√√√ √
• Replace brake pads. Whenever worn to the limit
5 * Rear brake• Check operation and adjust brake lever free play.
√√√√√ √
• Replace brake shoes. Whenever worn to the limit
6 * Brake hose• Check for cracks or damage.
• Check for correct routing and clamping.√√√√ √
• Replace. Every 4 years
7 * Wheels• Check runout and for damage.
√√√√
8 * Tires• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.√√√√ √
9 * Wheel bearings• Check bearing for looseness or damage.
√√√√
10 * Steering bearings• Check bearing play and steering for roughness.
√√√√√
• Lubricate with lithium-soap-based grease. Every 50000 km (30000 mi)
11 * Chassis fasteners• Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
53B-F8199-E0_CS.indd 6-453B-F8199-E0_CS.indd 6-4
2011/11/01 12:32:092011/11/01 12:32:09
Process BlackProcess Black
Page 54 of 84
1
2
3
4
5
6
7
8
9
6-17
EAU1722A
PERIODIC MAINTENANCE AND ADJUSTMENT
proved for this model.
Tire air pressure (measured on cold
tires):
Up to 90 kg (198 lb):
Front:
175 kPa (1.75 kgf/cm
2, 25 psi)
Rear:
200 kPa (2.00 kgf/cm2, 29 psi)
90 kg (198 lb) to maximum load:
Front:
175 kPa (1.75 kgf/cm2, 25 psi)
Rear:
225 kPa (2.25 kgf/cm2, 33 psi)
Maximum load*:
179 kg (395 lb)
*Total weight of rider, passenger,
cargo and accessories
EWA10511
WARNING
Never overload your vehicle. Op-
eration of an overloaded vehicle
could cause an accident.
EAUT2142
TiresTo maximize the performance, dura-
bility, and safe operation of your ve-
hicle, note the following points regard-
ing the specifi ed tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EWA10503
WARNING
Operation of this vehicle with im-
proper tire pressure may cause
severe injury or death from loss of
control.● The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the tempera-
ture of the tires equals the am-
bient temperature).● The tire air pressure must be
adjusted in accordance with
the riding speed and with the
total weight of rider, passen-
ger, cargo, and accessories ap-
EAU21401
Valve clearanceThe valve clearance changes with
use, resulting in improper air-fuel mix-
ture and/or engine noise. To prevent
this from occurring, the valve clear-
ance must be adjusted by a Yamaha
dealer at the intervals specifi ed in the
periodic maintenance and lubrication
chart.
53B-F8199-E0_CS.indd 6-1753B-F8199-E0_CS.indd 6-17
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black
Page 75 of 84
1
2
3
4
5
6
7
8
9
7-4
EAU25991
SCOOTER CARE AND STORAGE
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING!
To prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10951]
4. Lubricate all control cables and
the pivoting points of all levers
and pedals as well as of the
sidestand/centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then
lift the scooter so that both of its
wheels are off the ground. Alter-
natively, turn the wheels a little
every month in order to prevent
the tires from becoming degraded
in one spot.
6. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully
charge it. Store it in a cool,
dry place and charge it once a
month. Do not store the battery
in an excessively cold or warm
place [less than 0 °C (30 °F) or
more than 30 °C (90 °F)]. For
more information on storing the
battery, see page 6-26.
TIPMake any necessary repairs before
storing the scooter.
53B-F8199-E0_CS.indd 7-453B-F8199-E0_CS.indd 7-4
2011/11/01 12:32:102011/11/01 12:32:10
Process BlackProcess Black
Page 77 of 84
1
2
3
4
5
6
7
8
9
8-2
SPECIFICATIONS
Caster angle
23.83 degree
Trail
84 mm (3.3 in)Front tireType
Tubeless
Size
100 / 80 - 16M/C 50P
Manufacturer/model
DURO / DM1157FRear tireType
Tubeless
Size
120 / 80 - 16M/C 60P
Manufacturer/model
DURO / DM1157LoadingMaximum load
179 kg (395 lb)Tire air pressure (measured on cold
tires)Loading condition
90 kg (198 lb)
Front
175 kPa (1.75 kgf/cm
2, 25 psi, 1.75 bar)
Rear
200 kPa (2.00 kgf/cm2, 29 psi, 2.00 bar)
Loading condition
90 kg - maximum load
Front
175 kPa (1.75 kgf/cm2, 25 psi, 1.75 bar)Rear
225 kPa (2.25 kgf/cm
2, 33 psi, 2.25 bar)
Front wheelWheel type
Cast wheel
Rim size
J 16M/C MT2.50Rear wheelWheel type
Cast wheel
Rim size
J 16M/C MT2.75Front brakeType
Single disc brake
Operation
Right hand operation
Specifi ed brake fl uid
DOT 4Rear brakeType
Drum brake
Operation
Left hand operationFront suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
100.0 mm (3.94 in)Rear suspensionType
Unit swingSpring/shock absorber type
Coil spring/gas-oil damper
Wheel travel
92.0 mm (3.62 in)
Electrical systemIgnition system
TCI
Charging system
AC magnetoBatteryModel
GT7B-4
Voltage, capacity
12 V, 6.5 AhHeadlightBulb type
Halogen bulbBulb voltage, wattage x quantityHeadlight
12 V, 55 W x 2
Tail/brake light
12V, 0.25 / 1.4W 1 (LED ASSY)
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 10.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
License plate light
12 V, 5.0 W x 1
Meter lighting
12V,LED 6
High beam indicator light
12V,LED 1
53B-F8199-E0_CS.indd 8-253B-F8199-E0_CS.indd 8-2
2011/11/01 12:32:112011/11/01 12:32:11
Process BlackProcess Black
