MOTORCYCLE CARE AND STORAGE
7-2
1
2
3
4
5
67
8
9off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield. Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.TIPSalt sprayed on roads in the winter may
remain well into spring. 1. Clean the motorcycle with cold wa- ter and a mild detergent, after the
engine has cooled down.
NOTICE: Do not use warm water
since it increases the corrosive
action of the salt.
[ECA10791]
2. Apply a corrosion protection spray on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
4. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
1DX-9-E0.book 2 ページ 2011年10月10日 月曜日 午後2時14分
MOTORCYCLE CARE AND STORAGE
7-3
2
3
4
5
678
9
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
WARNING
EWA11131
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-nering behavior.
NOTICE
ECA10800
Apply spray oil and wax spar-
ingly and make sure to wipe off any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wearaway the paint.
TIP
Consult a Yamaha dealer for ad-
vice on what products to use.
Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
on for a short period of time will
help remove the moisture from thelens.
EAU43202
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust sys-
tem are cool before covering the motor-
cycle.NOTICE
ECA10810
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-cals are stored.
Long-term
Before storing your motorcycle for sev-
eral months: 1. Follow all the instructions in the “Care” section of this chapter.
2. Fill up the fuel tank and add fuel
1DX-9-E0.book 3 ページ 2011年10月10日 月曜日 午後2時14分
SPECIFICATIONS
8-2
1
2
3
4
5
6
78
9
Gear ratio:1st: 2.417 (29/12)
2nd: 1.733 (26/15)
3rd:
1.313 (21/16)
4th: 1.050 (21/20)
5th: 0.840 (21/25)Chassis:Frame type: Semi double cradle
Caster angle: 27.00
Trail:
115 mm (4.5 in)Front tire:Type: With tube
Size:
80/100-21M/C 51P
Manufacturer/model: BRIDGESTONE/GRITTY-ED03 ERear tire:Type:
With tube
Size: 120/90-18M/C 65P
Manufacturer/model: BRIDGESTONE/GRITTY-ED04 E Maximum load:
90 kg (198 lb)
* (Total weight of rider, cargo and accesso-
ries)
Tire air pressure (measured on cold
tires):Loading condition: 0–90 kg (0–198 lb)
Front: 150 kPa (1.50 kgf/cm
2, 22 psi)
Rear: 200 kPa (2.00 kgf/cm2, 29 psi)
Front wheel:Wheel type: Spoke wheel
Rim size: 21x1.60Rear wheel:Wheel type: Spoke wheel
Rim size: 18x2.15Front brake:Type: Single disc brake
Operation: Right hand operation
Specified brake fluid:
DOT 4Rear brake:Type: Single disc brake
Operation:
Right foot operation Specified brake fluid:
DOT 4
Front suspension:Type: Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel:
300.0 mm (11.81 in)Rear suspension:Type: Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel: 299.0 mm (11.77 in)Electrical system:Ignition system:
TCI
Charging system: AC magnetoBattery:Model:
YTZ7S(F)
Voltage, capacity: 12 V, 6.0 AhHeadlight:Bulb type:
Halogen bulbBulb voltage, wattage quantity:Headlight:
12 V, 35 W/35 W 1
Tail/brake light:
LED
1DX-9-E0.book 2 ページ 2011年10月10日 月曜日 午後2時14分
SPECIFICATIONS
8-3
2
3
4
5
6
789
Front turn signal light: 12 V, 10.0 W 2
Rear turn signal light:
12 V, 10.0 W 2
Auxiliary light: 12 V, 5.0 W 1
License plate light: 12 V, 5.0 W 1
Meter lighting:
EL (Electroluminescent)
Neutral indicator light: 12 V, 1.7 W 1
High beam indicator light: 12 V, 1.7 W 1
Turn signal indicator light:
12 V, 1.7 W 1
Fuel level warning light: LED
Engine trouble warning light: 12 V, 1.7 W 1Fuses:Main fuse:
15.0 A
1DX-9-E0.book 3 ページ 2011年10月10日 月曜日 午後2時14分
INDEX
AAir filter element and check hose,
cleaning ................................................. 6-14
Auxiliary light bulb, replacing ................... 6-35BBattery ..................................................... 6-30
Brake and clutch levers, checking and lubricating .............................................. 6-27
Brake fluid, changing ............................... 6-24
Brake fluid level, checking ....................... 6-23
Brake lever ................................................ 3-8
Brake lever free play, checking ............... 6-21
Brake light switches ................................. 6-22
Brake pedal ............................................... 3-9
Brake pedal, checking and lubricating ..... 6-28CCables, checking and lubricating ............. 6-26
Care ........................................................... 7-1
Catalytic converter ................................... 3-11
Clutch lever................................................ 3-8
Clutch lever free play, adjusting .............. 6-20
Coolant .................................................... 6-12DDimmer switch ........................................... 3-7
Drive chain, cleaning and lubricating ....... 6-26
Drive chain slack ..................................... 6-24EEngine break-in ......................................... 5-4
Engine idling speed ................................. 6-17
Engine oil and oil filter element.................. 6-8
Engine, starting a warm ............................. 5-2
Engine stop switch..................................... 3-7
Engine trouble warning light ...................... 3-2
FFront and rear brake pads, checking ...... 6-22
Front fork, adjusting ................................ 3-14
Front fork, bleeding ................................. 3-15
Front fork, checking................................. 6-29
Fuel ......................................................... 3-10
Fuel consumption, tips for reducing .......... 5-3
Fuel level warning light .............................. 3-2
Fuel tank breather hose .......................... 3-11
Fuel tank cap............................................. 3-9
Fuse, replacing........................................ 6-31HHandlebar switches ................................... 3-7
Headlight bulb, replacing......................... 6-32
High beam indicator light ........................... 3-2
Horn switch ............................................... 3-7IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-19
Indicator lights and warning lights ............. 3-1KKickstarter ............................................... 3-12LLicense plate light bulb, replacing ........... 6-34MMain switch ............................................... 3-1
Maintenance and lubricatio n, periodic....... 6-4
Maintenance, emission control system ..... 6-3
Matte color, caution ................................... 7-1
Model label ................................................ 9-1
Multi-function display................................. 3-2NNeutral indicator light ................................ 3-1
PPanel, removing and installing ...................6-7
Parking.......................................................5-5
Part locations .............................................2-1SSafety information ......................................1-1
Seat ......................................................... 3-13
Shifting .......................................................5-3
Shift pedal ..................................................3-8
Shift pedal, checking................................ 6-22
Shock absorber assembly, adjusting .......3-16
Sidestand .................................................3-18
Sidestand, checking and lubricating ........6-28
Spark plug, checking .................................6-7
Specifications.............................................8-1
Starter knob .............................................3-12
Starting a cold engine ................................5-1
Start switch ................................................3-7
Steering, checking ................................... 6-29
Steering lock ............................................3-13
Storage ......................................................7-3
Supporting the motorcycle .......................6-35
Swingarm pivots, lubricating .................... 6-28TTail/brake light ......................................... 6-33
Throttle grip and cable, checking and lubricating ..............................................6-27
Throttle grip free play, checking............... 6-17
Tires ......................................................... 6-18
Tool kit .......................................................6-2
Troubleshooting ....................................... 6-39
Troubleshooting charts ............................6-40
Turn signal indicator light ...........................3-1
Turn signal light bul b, replacing ............... 6-34
1DX-9-E0.book 2 ページ 2011年10月10日 月曜日 午後2時14分