2012 YAMAHA VMAX key battery

INSTRUMENT AND CONTROL FUNCTIONS
3-3
3
EAU10683
LOCK
The steering is locked, and all electrical
systems are off. The key can be re-
moved.
To lock the steering1. Turn the handlebars all the way tothe left.
2. Push the key in from the “OFF” po- sition, and then turn it to “LOCK”
while still pushing it.
3. Remove the key. To unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
EAU34341
(Parking)
The steering is locked, and the taillight,
license plate light and auxiliary light are
on. The hazard lights and turn signal
lights can be turned on, but all other
electrical systems are off. The key can
be removed.
The steering must be locked before the
key can be turned to “ ”.
NOTICE
ECA11020
Do not use the parking position for
an extended length of time, other-
wise the battery may discharge.
1. Push.
2. Turn.12
1. Push.
2. Turn.12
U2S3E3E0.book Page 3 Monday, September 19, 2011 8:42 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
6
EAU46555
Battery The battery is located under cowling A.
(See page 6-8.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to be
checked and, if necessary, tightened.
WARNING
EWA10760
●
Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID. EXTERNAL: Flush with plenty of water.
INTERNAL: Drink large quan- tities of water or milk and im-
mediately call a physician.
EYES: Flush with water for 15 minutes and seek prompt
medical attention.
●
Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.
●
KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
To remove the battery1. Remove cowling A. (See page 6-8.)
2. Disconnect the negative battery lead first, then the positive battery
lead by removing their bolt.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive lead.
[ECA16302]
3. Remove the battery cover bolts, lift the battery cover (together with the
ECU), then move the cover to the
side.1. Negative battery lead (black)
2. Positive battery lead (red)
1. Battery cover bolt
2. Battery cover2
1
1
2
U2S3E3E0.book Page 31 Monday, September 19, 2011 8:42 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-32
6
4. Remove the main fuse (together
with the holding band) from its
holder.
5. Disconnect coupler A.
6. Remove the rubber damper. 7. Unfold the heat insulator as
shown.
8. Pull the battery out of its compart- ment.
To charge the battery
Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
NOTICE
ECA16521
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (con-
stant-voltage) battery charger is re-
quired. Using a conventional battery
charger will damage the battery.To store the battery 1. If the vehicle will not be used for more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive lead.
[ECA16302]
2. If the battery will be stored for more than two months, check it at least
once a month and fully charge it if
necessary.
To install the batteryTIPBe sure the battery is fully charged.
1. Main fuse
2. Holding band
3. Coupler A
1. Rubber damper2
1
3
1
1. Heat insulator
2. Battery1
2
U2S3E3E0.book Page 32 Monday, September 19, 2011 8:42 AM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-33
61. Place the battery in its compart-
ment.
2. Fold the heat insulator back to its original position. NOTICE: Make
sure that the heat insulator is in
its original position and it is
properly folded.
[ECA16550]
3. Install the rubber damper.
4. Connect coupler A.
5. Install the main fuse (together with the holding band) on its holder.
6. Place the battery cover (together with the ECU) in the original posi-
tion, and then install the bolts.
7. Connect the positive battery lead first, then connect the negative
battery lead by installing their bolt.
NOTICE: When installing the battery, be sure the key is
turned to “OFF”, then connect
the positive lead before con-
necting the negative lead.
[ECA16840]
8. Install the cowling.NOTICE
ECA16530
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
EAU46453
Replacing the fuses The main fuse and the ABS motor fuse
are located behind cowling A. (See
page 6-8.) Fuse box 1 is located under
the rider seat. (See page 3-25.)
1. Heat insulator1
1. Main fuse
2. ABS motor fuse
3. ABS motor spare fuse
1
3
2
U2S3E3E0.book Page 33 Monday, September 19, 2011 8:42 AM