2012 YAMAHA TZR50 torque

EAU17244
Periodic inspection, adjustment, and
lubrication will keep your vehicle in
the safest and most efficient condi-
tion possible. Safety is an obligation
of the vehicle owner/operator. The
most important points of vehicle ins-
pection, adjustment, and lubrication
are explained on the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a general guide under
normal riding conditions. However,
depending on the weather, terrain,
geographical location, and individual
use, the maintenance intervals may
need to be shortened.
EWA10321
Failure to properly maintain the
vehicle or performing maintenance
activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle
service, have a Yamaha dealer per-
form service.
EWA15122
Turn off the engine when perfor-
ming maintenance unless otherwi-
se specified.
A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Running the engine while servi-
cing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-1 for more
information about carbon
monoxide.
EWA15460
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before tou-
ching them.
EAU17521
Owner’s tool kit
1. Owner’s tool kit
The owner’s tool kit is located inside
the storage compartment under the
seat. (See page 3-12).
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to
assist you in the performance of pre-
ventive maintenance and minor
repairs. However, additional tools
such as a torque wrench may be
necessary to perform certain mainte-
nance work correctly.
WARNING
WARNING
WARNING
PERIODIC MAINTENANCE AND ADJUSTMENT
6-1
6
1HD-F819D-E0 7/3/11 20:27 Página 38
2AS-F819D-E0.indd 3831/07/12 10:09

3. Remove the spark plug asshown, using the spark plug
wrench, which is located in the
storage compartment. (See page
6-1).
1. Spark plug wrench
To check the spark plug1. Check that the porcelain insula- tor around the center electrode of
the spark plug is a medium-to-
light tan (the ideal color when the
vehicle is ridden normally).
TIP
If the spark plug shows a distinctly
different color, the engine could be
operating improperly. Do not attempt
to diagnose such problems yourself. Instead, have a Yamaha dealer check
the vehicle.
2. Check the spark plug for electro-
de erosion and excessive carbon
or other deposits, and replace it if
necessary.
To install the spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if
necessary, adjust the gap to spe-
cification.
1. Spark plug gap
2. Clean the surface of the sparkplug gasket and its mating surfa-
ce, and then wipe off any grime
from the spark plug threads.
3. Install the spark plug with the spark plug wrench, and then
tighten it to the specified torque.
TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4–1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
4. Install the spark plug cap.
5. Install the panel.
Tightening torque:Spark plug: 22.5 Nm (2.2 m•kgf, 16.3 ft•lbf)
Spark plug gap:0.6–0.7 mm (0.024–0.028 in)
1
Specified spark plug:NGK / BR9 ES


PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
6
1HD-F819D-E0 7/3/11 20:27 Página 49
2AS-F819D-E0.indd 4931/07/12 10:09

EAUS1591
Transmission oil
The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Transmission oil filler cap
2. Transmission oil check bolt
1. Remove cowling A. (See page 6-8).
2. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.
TIP
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
3. Remove the oil check bolt, andthen check the oil level.
TIP
The oil should be at the brim of the
check hole.
4. If the oil is below the brim of thecheck hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
5. Install the oil check bolt, and then tighten it to the specified torque. To change the transmission oil
1. Transmission oil check bolt
2. Transmission oil drain bolt
3. Washer
1. Place an oil pan under the trans-
mission oil case to collect the
used oil.
2. Remove the drain bolt and the oil check bolt to drain the oil.
3. Install the drain bolt and the check bolt, and then tighten them
to the specified torques.
Tightening torque:Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-13
6
1HD-F819D-E0 7/3/11 20:27 Página 50
2AS-F819D-E0.indd 5031/07/12 10:09

4. Remove the oil filler cap, refillwith the specified amount of the
recommended transmission oil,
and then install and tighten the oil
filler cap. NOTICE: Make sure
that no foreign material enters
the transmission case.
[ECAM1021]
5. Start the engine and let it idle for several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
EAU20070
Coolant
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU39087
To check the coolant level1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion.
TIP
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in thecoolant reservoir.
TIP
The coolant should be between the
minimum and maximum level marks.
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below theminimum level mark, remove
panel A to access the coolant
reservoir. (See page 6-8).
4. Remove the coolant reservoir cap, add coolant to the maxi-
mum level mark, and then install
the reservoir cap. WARNING!
Remove only the coolant reser-
voir cap. Never attempt to
remove the radiator cap when
the engine is hot.
[EWA15161]
Recommended transmission oil: See page 8-1
Oil change quantity: 0.75 L (0.79 US qt, 0.66 Imp.qt)
Tightening torque:Transmission oil drain bolt: 17.5 Nm (1.7 m•kgf, 12.7 ft•lbf)
Oil check bolt: 6 Nm (0.6 m•kgf, 4.3 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-14
6
1HD-F819D-E0 7/3/11 20:27 Página 51
2AS-F819D-E0.indd 5131/07/12 10:09

6. Remove the coolant reservoircap.
1. Coolant reservoir cap
7. Move the hose clamp in thedirection shown, and then dis-
connect the coolant reservoir
hose to drain the reservoir.
1. Hose clamp
2. Coolant reservoir hose
3. Coolant reservoir
8. After the coolant is completely
drained, thoroughly flush the
cooling system with clean tap
water.
9. Connect the coolant reservoir hose, and then move the hose
clamp back to its original posi-
tion.
10. Install the coolant drain bolt and its new gasket, and then tighten
the bolt to the specified torque.
11. Pour the recommended coolant into the reservoir to the maximum
level mark, and then install the
coolant reservoir cap.
12. Pour the recommended coolant into the radiator until it is full. 13. Install the radiator cap, start the
engine, let it idle for several minu-
tes, and then turn it off.
14. Remove the radiator cap to check the coolant level in the
radiator. If necessary, add suffi-
cient coolant until it reaches the
top of the radiator, and then ins-
tall the radiator cap, retainer and
retaining bolt.
15. Check the coolant level in the reservoir. If necessary, remove
the coolant reservoir cap, add
coolant to the maximum level
mark, and then install the cap.Antifreeze/water mixture ratio:1:1
Recommended antifreeze: High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Coolant quantity: Radiator capacity (including all
routes): 0.70 L (0.74 US qt, 0.62 Imp.qt)
Coolant reservoir capacity (up to
the maximum level mark): 0.29 L (0.31 US qt, 0.26 Imp.qt)
Tightening torque:Coolant drain bolt: 9 Nm (0.9 m•kgf, 6.5 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-16
6
1HD-F819D-E0 7/3/11 20:27 Página 53
2AS-F819D-E0.indd 5331/07/12 10:09

1. Brake pad wear indicator groove
2. Install the brake caliper bolt, andthen tighten it to the specified
torque.
EAU22580
Checking the brake fluid
level
Front brake
1. Minimum level mark
Rear brake
1. Minimum level mark
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Before riding, check that the brake
fluid is above the minimum level mark
and replenish if necessary. A low bra-
ke fluid level may indicate worn brake
pads and/or brake system leakage. If
the brake fluid level is low, be sure to
check the brake pads for wear and
the brake system for leakage.
Observe these precautions:
When checking the fluid level,
make sure that the top of the bra-
ke fluid reservoir is level.
Use only the recommended qua-
lity brake fluid, otherwise the rub-
ber seals may deteriorate, cau-
sing leakage and poor braking
performance.
Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performan-
ce.
Recommended brake fluid:DOT 4
Tightening torque:Brake caliper bolt: 30 Nm (3.0 m•kgf, 21.7 ft•lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-24
6
1HD-F819D-E0 7/3/11 20:27 Página 61
2AS-F819D-E0.indd 6131/07/12 10:09

3. Measure the drive chain slack asshown.
4. If the drive chain slack is inco- rrect, adjust it as follows.
TIP
When checking the drive chain slack,
the chain tensioner should not be tou-
ching the drive chain.
EAU22922
To adjust the drive chain slack
Consult a Yamaha dealer before
adjusting the drive chain slack.1. Remove the cotter pin from the axle nut, and then loosen the axle
nut.
2. Loosen the chain puller locknut at each end of the swingarm.
3. To tighten the drive chain, turn the drive chain slack adjusting
nut at each end of the swingarm
in direction (a). To loosen the dri-
ve chain, turn the adjusting nut at
each end of the swingarm in direction (b), and then push the
rear wheel forward.
NOTICE:
Improper drive chain slack will
overload the engine as well as
other vital parts of the
motorcycle and can lead to
chain slippage or breakage. To
prevent this from occurring,
keep the drive chain slack wit-
hin the specified limits.
[ECA10571]
TIP
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
1. Drive chain slack adjusting bolt
2. Drive chain puller locknut
3. Alignment marks
4. Tighten the locknuts, and then tighten the axle nut to the speci-
fied torque.
5. Insert a new cotter pin into the axle nut, and then bend its ends
as shown. WARNING! Always
use a new cotter pin for the
axle nut.
[EWA10701]
1. Axle nut cotter pin
2. Axle nut
3. Drive chain puller locknut
4. Drive chain slack adjusting bolt
5. Alignment marks
Tightening torque:Axle nut: 90 Nm (9.0 m•kgf, 65.1 ft•lbf)
Drive chain slack:20.0–25.0 mm (0.79–0.98 in)
PERIODIC MAINTENANCE AND ADJUSTMENT
6-26
6
1HD-F819D-E0 7/3/11 20:27 Página 63
2AS-F819D-E0.indd 6331/07/12 10:09