Page 330 of 580
330 3-1. Using the air conditioning system and defogger
PRIUS +_OM_OM47821E_(EE)Adjusting the temperature setting
Slide to the left or right to select the temperature set-
ting display ( ).
Turn to the clockwise to raise the temperature, or
counterclockwise to lower.
Changing the air outlets
Slide to the left to select the air outlet display
().
Turn clockwise or counterclockwise.
The air flow shown on the display indicates the following:
Air flows to the upper body.
STEP 1
STEP 2
STEP 1
STEP 2
Page 364 of 580
364
3-5. Other interior features
PRIUS +_OM_OM47821E_(EE)
Clock
The clock is displayed when
The “POWER” switch is in ON mode.
After turning the “POWER” switch off
Even after the “POWER” switch has been turned off, the time will continue to
be displayed for approximately 30 seconds or until a door is locked.
When the 12-volt battery is disconnected
The time display will automatically be set to 1:00.
Adjusts the hours
Adjusts the minutes
Rounds to the nearest
hour
*
*
: e.g. 1:00 to 1:29 1:00
1:30 to 1:59 2:00
Page 406 of 580

406 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47821E_(EE)Make sure to check the oil type and prepare the items needed before
adding oil.
Remove the oil filler cap by turning it counterclockwise.
Add engine oil slowly, checking the dipstick.
Install the oil filler cap by turning it clockwise.
Engine oil selectionP. 544
Oil quantity
(Low Full)1.5 L (1.6 qt., 1.3 Imp.qt.)
Items Clean funnel
Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the follow-
ing situations, oil consumption may increase, and engine oil may need to be
refilled in between oil maintenance intervals.
When the engine is new, for example directly after purchasing the vehicle
or after replacing the engine
If low quality oil or oil of an inappropriate viscosity is used
When driving at high engine speeds or with a heavy load, or when driving
while accelerating or decelerating frequently
When leaving the engine idling for a long time, or when driving frequently
through heavy traffic
STEP 1
STEP 2
STEP 3
Page 442 of 580
442 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47821E_(EE)
FUSEAmpereCircuit
26 WIP 30A Windshield wipers
27 MET 7.5A Gauges and meters
28 IGN 10ABrake system, driver support sys-
tem, multiport fuel injection sys-
tem/sequential multiport fuel
injection system, SRS airbag sys-
tem, smart entry & start system
29 PANEL 10AAir conditioning system, emer-
gency flashers, seat heaters,
transmission, P position switch,
navigation system, intelligent park-
ing assist system, headlight
cleaner, seat belt reminder light,
headlight leveling system, glove
box light, clock, audio system,
head-up display
30 TAIL 10AHeadlight leveling system, front
position lights, tail lights, license
plate lights, front fog lights, rear
fog light
Page 447 of 580
447 4-3. Do-it-yourself maintenance
4
Maintenance and care
PRIUS +_OM_OM47821E_(EE)
Replacing light bulbs
Headlight low beams (halogen headlights)
Turn the bulb base counterclock-
wise.
Unplug the connector while
pressing the lock release.
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb
with the mounting, and insert.
STEP 1
STEP 2
STEP 3
Page 448 of 580
448 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47821E_(EE)Turn and secure the bulb base.
Shake the bulb base gently to
check that it is not loose, turn the
headlights on once and visually
confirm that no light is leaking
through the mounting.
Headlight high beams
Turn the bulb base counterclockwise.
Vehicles with halogen headlights
Vehicles with LED headlights
STEP 4
STEP 1
Page 450 of 580
450 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47821E_(EE)Front position lights
Turn the bulb base counterclockwise.
Vehicles with halogen headlights
Vehicles with LED headlights
Remove the light bulb.
When installing, reverse the steps listed.
STEP 1
STEP 2
STEP 3
Page 452 of 580
452 4-3. Do-it-yourself maintenance
PRIUS +_OM_OM47821E_(EE)Turn the bulb base counterclock-
wise.
When installing, reverse the steps listed.
After installing the bulb base, shake the bulb base gently to check
that it is not loose.
STEP 3
STEP 4