2012 TOYOTA HILUX bulb

1
2
3
4
5
6
5
HILUX_EE (OM0K132E)
4-1. Maintenance and care
Cleaning and protecting
the vehicle exterior ........... 462
Cleaning and protecting
the vehicle interior ............ 466
4-2. Maintenance
Maintenance
requirements..................... 470
4-3. Do-it-yourself maintenance
Do-it-yourself service
precautions ....................... 474
Hood ................................... 478
Engine compartment........... 480
Tires .................................... 496
Tire inflation pressure ......... 500
Wheels ................................ 502
Air conditioning filter ........... 504
Wireless remote control
battery............................... 506
Checking and replacing
fuses ................................. 509
Light bulbs .......................... 5255-1. Essential information
Emergency flashers ........... 540
If your vehicle needs to
be towed .......................... 541
If you think something
is wrong............................ 547
Fuel pump shut off
system.............................. 548
5-2. Steps to take in an emergency
If a warning light turns on
or a warning buzzer
sounds ............................. 549
If you have a flat tire ........... 557
If the engine will not
start .................................. 576
If the shift lever cannot be
shifted from P ................... 577
If you lose your keys .......... 578
If the vehicle battery
is discharged .................... 579
If your vehicle overheats .... 584
If you run out of fuel and
the engine stalls ............... 587
If the vehicle becomes
stuck................................. 588
If your vehicle has to be
stopped in an
emergency ....................... 590
4Maintenance and care5When trouble arises

173
2-1. Driving procedures
2
When driving
HILUX_EE (OM0K132E)
Turn signal lever
Turn signals can be operated when
The engine switch is in the “ON” position.
If the indicator flashes faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned
out.
The turn signal lever can be used to show the following intentions
of the driver:
Right turn
Left turn
Lane change to the right
(push and hold the lever
partway)
The right hand signals will
flash until you release the
lever.
Lane change to the left
(push and hold the lever
partway)
The left hand signals will flash
until you release the lever.

4Maintenance and care
461
HILUX_EE (OM0K132E)
4-1. Maintenance and care
Cleaning and protecting
the vehicle exterior ......... 462
Cleaning and protecting
the vehicle interior .......... 466
4-2. Maintenance
Maintenance
requirements................... 470
4-3. Do-it-yourself maintenance
Do-it-yourself service
precautions ..................... 474
Hood ................................. 478
Engine compartment......... 480
Tires .................................. 496
Tire inflation pressure ....... 500
Wheels .............................. 502
Air conditioning filter ......... 504
Wireless remote control
battery............................. 506
Checking and replacing
fuses ............................... 509
Light bulbs ........................ 525

475 4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_EE (OM0K132E)
ItemsParts and tools
Fuses (P. 509)• Fuse with same amperage rating
as original
Light bulbs (P. 525)
• Bulb with same number and watt-
age rating as original
• Phillips-head screwdriver
• Wrench
Radiator, condenser and
intercooler
(P. 488)
Tire inflation pressure (P. 500)• Tire pressure gauge
• Compressed air source
Washer fluid (P. 493)
• Water or washer fluid containing
antifreeze (for winter use)
• Funnel (used only for adding
water or washer fluid)

524 4-3. Do-it-yourself maintenance
HILUX_EE (OM0K132E)
After a fuse is replaced
If the lights do not turn on even after the fuse has been replaced, a bulb
may need replacement. (P. 525)
If the replaced fuse blows again, have the vehicle inspected by any
authorized Toyota dealer or repairer, or another duly qualified and
equipped professional.
If there is an overload in a circuit
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failure to do so may cause damage, and possibly a fire or injury.
Never use a fuse of a higher amperage rating than that indicated, or use
any other object in place of a fuse.
Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
This can cause extensive damage or even fire.
Do not modify the fuses or fuse boxes.
NOTICE
Before replacing fuses
Have the cause of electrical overload determined and repaired by any autho-
rized Toyota dealer or repairer, or another duly qualified and equipped pro-
fessional, as soon as possible.

525
4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_EE (OM0K132E)
Light bulbs
You may replace the following bulbs by yourself. The difficulty level
of replacement varies depending on the bulb. As there is a danger
that components may be damaged, we recommend that replacement
is carried out by any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
Preparing for light bulb replacement
Check the wattage of the light bulb to be replaced. (P. 614)
Front bulb locations
Front fog light*Front position light Side turn signal light
*
(fender-mounted type)
Headlight
Front turn signal light

526 4-3. Do-it-yourself maintenance
HILUX_EE (OM0K132E)
Replacing light bulbs
Headlight
Before replacing the bulbs (right side only):
Release the clips of the air
cleaner filter cover, and remove
the cover to allow easy access to
the light bulbs.
Rear bulb locations
*: If equipped
Rear fog light
(right-hand drive vehicles)
or back-up light Stop/tail lights
Rear turn signal lightLicense plate
lights
Rear fog light
(left-hand drive vehicles)
or back-up light
STEP1

527 4-3. Do-it-yourself maintenance
4
Maintenance and care
HILUX_EE (OM0K132E)Unplug the connector and
remove the rubber cover.
Release the bulb retaining
spring.
Remove the bulb.
To install a new bulb, align the
tabs of the bulb with the cutouts
of the mounting hole.
STEP2
STEP3
STEP4